• This unit requires connection to a grounded (three- Installation of the CLR2060 ..... . 17 prong), polarized receptacle that has been placed by a qualified electrician in accordance with applicable Installation Troubleshooting .
Page 3
2 Inspect and Plan Use this appliance for its intended purpose only and follow these general precautions along with those listed You have received a carton containing your CLR2060 Clear throughout this guide: Ice Maker with a package inside containing a User Manual, a Product Registration Card and water connection parts.
™ CLR2060 — Clear Ice Maker Product Dimensions 3 Prepare Site 24" 26-1/8" Your U-Line product has been designed for either free- Including Including standing or built-in installation. When built-in, your unit Handle Handle does not require additional air space for top, sides or rear.
™ CLR2060 — Clear Ice Maker Reversing the Door 4. Remove the two door closer inserts from the existing bottom hinge and install as shown on the new bottom (Black and White Units Only) hinge (see Figure 8). All U-Line units (except...
For more information see Page 15. For example: Drain Placing a CLR2060 Clear Ice Maker next to a 2015R The unit’s generous 7-inch drain connection height Refrigerator would require a cut-out width of: extends the distance the unit can be located from a 15-3/16"...
™ CLR2060 — Clear Ice Maker 4 Prepare and Install Door Panel (Black and White Units Only) Two types of custom door panels can be installed on your Black or White unit to harmonize with or accent the surrounding décor: a Custom 1/4" Insert or a Full Overlay.
3/8" A full overlay door panel completely covers the 3/8" doorframe and handle to give a built-in appearance. See your U-Line dealer for the optional Full Overlay Door Door Bottom: 13/16" 5/16" Dia. x 1/4" Deep Panel Kit (P/N U-OL2015B — Black or P/N U-OL2015W —...
Page 9
™ CLR2060 — Clear Ice Maker 4. Drill hole for upper door hinge (top of panel) (see 4. Remove the top handle and discard. (This handle will be Figure 16, Top View). replaced with the Modified Handle included in the Full Overlay Door Panel Kit.)
Page 10
™ CLR2060 — Clear Ice Maker Typical Door Panel Tape Back of Wood Panel Removed Wood Door Panel Panel Pivot Plate #10 x 5/8" Round Head Screw Six Required Plastic Spacer Six Required Side of Wood Panel Bottom of Figure 22 Wood Panel 5/16"...
™ CLR2060 — Clear Ice Maker 5 Adjust Door Pivot Post Wood Panel Top Hinge Plate (5/8" Longer than Existing Top Hinge Plate) Checking Door Alignment The unit’s door is aligned at the factory before shipment. However, its alignment could have been disturbed during #8-32 x 1/2"...
3. See Figure 28. If the top far edge of the door needs to The CLR2060 can be installed using a Gravity Drain, a move UP, move the hinge plate toward the outside of Factory-Installed Drain Pump (U-Line P60) or a Locally- the door and retighten screws.
Page 13
Gravity Drain, you may have ordered the CLR2060 with a U-Line P60 Drain Pump. See Figure 34 Figures 32, 33 and 34 for typical installations requiring a Drain Pump.
Page 14
CLR2060 with factory-installed pump, touch any components except the discharge tube we strongly recommend the use of the U-Line P60 drain during testing. Failure to follow this warning pump. The U-Line P60 drain pump is available through could result in serious personal injury or death.
Avoid kinking the water supply line. In the event of a power outage, restricted drain or pump failure, the failure to use the U-Line P60 drain pump or a pump with the above listed specifications, could result in substantial water leakage and pooling with severe and costly water damage and related consequential damages and harm.
1. Use a level to check the Plugging the unit into a receptacle located behind an levelness of the ice maker adjacent cabinet will allow the CLR2060 to be more easily from front to back and serviced with self-diagnostics without disturbing your from side to side.
™ CLR2060 — Clear Ice Maker 2. If the ice maker is not level, adjust the feet on the 9 Install the Unit corners of the unit as necessary (see Figure 44). Installation of the CLR2060 1. Open the water supply valve in the main water source.
™ CLR2060 — Clear Ice Maker Installation Troubleshooting 10 Start-Up for the First Time Problem Initial Start-Up Water is leaking under the unit. Once installation and leveling is complete, the unit is ready for initial start-up and operation. The cycle selector Solution switch is located in the front grille (see Figure 45).
™ CLR2060 — Clear Ice Maker 4. Watch the water flow over the evaporator assembly (ice Start-Up Troubleshooting cube tray) to familiarize yourself with the operation. Upon initial start-up, water flow over the evaporator Problem may be uneven. This may cause uneven sized cubes or water spilling into the ice storage bin.
For more than four decades, U-Line has distinguished itself as the leader in built-in undercounter ice making, refrigeration and wine storage appliances. U-Line Corporation, located in Milwaukee, WI, is a family operated manufacturer of built-in undercounter icemakers, Combo ®...