NWA1100 QUICK START GUIDE 802.11g Business WLAN Access Point Firmware v1.00 Edition 1, 07/2008 DEFAULT LOGIN DETAILS IP Address: http://192.168.1.2 Password: 1234 CONTENTS ENGLISH DEUTSCH ESPAÑOL FRANÇAIS ITALIANO РУССКИЙ SVENSKA 简体中文 繁體中文 www.zyxel.com Copyright 2008 ZyXEL Communications Corporation...
ENGLISH ENGLISH ENGLISH Overview This Quick Start Guide shows how to set up and configure the NWA1100 (marked Z in the figure) to allow wireless clients to securely access your wired network. See your User’s Guide for more information. You may need your Internet access information. To set up your wireless network you need to: •...
Page 4
ENGLISH Connect the Hardware 1. Using the grey Ethernet cable, connect the ETHERNET port to a computer for initial configuration. 2. Connect the POWER 12VDC socket to a power source using only the included power adaptor. Connect the NWA1100’s ETHERNET port to an Ethernet jack with network access after you have completed the initial configuration.
Page 5
ENGLISH ENGLISH LEDs • The SYS LED blinks amber, then turns steady green when the power is connected. • One of the LEDs by the ETHERNET port turns on if the port is properly connected, and blinks when there is traffic. The amber light shines if the connection is at 100 Mbps.
Page 6
ENGLISH Access the Web Configurator Use Internet Explorer 6.0 and later or Netscape Navigator 7.0 and later versions with JavaScript enabled and pop-up blocking disabled. Set Up Your Computer’s IP Address Note down your computer’s current IP settings before you change them.
Page 7
ENGLISH ENGLISH Log Into the Web Configurator Even though you can connect to the NWA1100 wirelessly, it is recommended that you connect your computer to the ETHERNET port for initial configuration. 1. Launch your web browser. Enter 192.168.1.2 (the NWA1100’s default IP address) as the address.
Page 8
ENGLISH 3. Change the login password by entering a new password and clicking Apply. Be sure to record the new password and keep it in a safe place. If you change the password and then forget it, you will need to reset the NWA1100.
Page 9
ENGLISH ENGLISH Configure the NWA1100 Configure System Settings 1. Click SYSTEM in the navigation panel. 2. The SYSTEM > General screen appears.
Page 10
ENGLISH System Name is for identifying the NWA1100 on your network. Choose a distinctive name, or leave this at its default. DNS Server(s): if your ISP gave you specific DNS (Domain Name System) settings, select User-Defined and enter them here. Otherwise, leave these fields at their defaults.
ENGLISH ENGLISH Configure Wireless Settings 1. Click WIRELESS in the navigation panel. The Wireless Settings screen displays. The wireless stations and the NWA1100 must use the same SSID, channel ID and encryption settings for wireless communication. Operation Mode: Ensure that AP mode is selected. Wireless Mode: Select the wireless standard you want your network to use.
Page 12
ENGLISH 3. Click the Security tab. If you don’t configure wireless security, anyone can access your network. This is where you can enter the security settings for your wireless network. The fields you fill in differ according to the type of security you select in the Security Mode field.
Page 13
ENGLISH ENGLISH Configure IP Settings 1. You need to set your NWA1100’s IP address to be in the same subnet as your network. Click IP in the navigation panel. Select Get automatically from DHCP if you want to have a DHCP server on your network assign an IP address to the NWA1100.
Page 14
ENGLISH If you change the NWA1100’s IP address, you must use the new IP address when you next access the web configurator. If you select Get automatically from DHCP, check your DHCP server to determine the IP address it assigns to the NWA1100. Refer to your DHCP server’s documentation for more information.
ENGLISH ENGLISH Install the Hardware Figures in this section use generic icons. The ZyXEL Device in the picture is not an exact representation of your device. Attaching Antennas Screw the antennas clockwise onto the antenna connectors on the sides of your NWA1100. The antennas should be perpendicular to the ground and parallel to each other.
Page 16
ENGLISH 1. Screw the two screws provided with your NWA1100 into the wall 60mm apart (see the figure in step 3). Use screws with 6mm ~ 8mm (0.24" ~ 0.31") wide heads. Do not screw the screws all the way in to the wall; leave a small gap between the head of the screw and the wall.
Page 17
ENGLISH ENGLISH 2. Adjust the cables. Run the connection cables down the back of the NWA1100 as shown in the following figure. Run the connection cables upward and along the edge of the ceiling. 3. Align the holes on the back of the NWA1100 with the screws on the wall.
Page 18
ENGLISH Set Up Power over Ethernet (Optional) Power over Ethernet (PoE) is the ability to provide power to your NWA1100 via an 8-pin CAT 5 Ethernet cable, eliminating the need for a nearby power source. A PoE injector (not included) is also needed to supply the Ethernet cable with power.
DEUTSCH DEUTSCH ENGLISH Übersicht In dieser Kurzanleitung erfahren Sie, wie das NWA-1100 (im Beispiel unten mit einem Z gekennzeichnet) installiert und konfiguriert wird, damit Wireless- Clients sicher auf Ihr kabelgebundenes Netzwerk zugreifen können. Weitere Informationen finden Sie im Benutzerhandbuch. Halten Sie die Daten für Ihren Internetzugang bereit. Um das Drahtlosnetzwerk einzurichten, müssen Sie: •...
Page 20
ENGLISH Anschließen der Hardware 1. Verbinden Sie für die Erstkonfiguration den ETHERNET-Anschluss mit dem grauen Ethernet-Kabel mit dem Computer. 2. Verbinden Sie die 12VDC-Netzanschlussbuchse POWER des Geräts mit dem mitgelieferten Netzadapter mit dem Stromnetz. Nachdem Sie die Erstkonfiguration durchgeführt haben, verbinden Sie den ETHERNET-Anschluss des NWA-1100s mit einem Ethernetanschluss mit Netzwerkverbindung.
Page 21
DEUTSCH ENGLISH LED-Anzeigen • Die LED-Anzeige SYS blinkt zunächst gelb und beginnt grün zu leuchten, sobald das Gerät mit Strom versorgt wird. • Eine der LEDs am ETHERNET-Port beginnt zu leuchten, wenn der Anschluss richtig verbunden ist. Bei Datenverkehr blinkt sie. Die gelbe LED leuchtet, bei einer 100-Mbps-Verbindung.
Page 22
ENGLISH Zugreifen auf den Web- Konfigurator Verwenden Sie den Internet Explorer 6.0 oder den Netscape Navigator 7.0 und neuere Versionen davon mit aktiviertem JavaScript und aktivierter Pop-up-Funktion. Einrichten der IP-Adresse des Computers Notieren Sie sich die aktuellen IP-Einstellungen des Computers, bevor Sie sie ändern.
Page 23
DEUTSCH ENGLISH 2. Geben Sie 1234 (das Standardkennwort) in das Feld Password (Kennwort) ein, und klicken Sie auf Login (Anmelden). 3. Ändern Sie das Kennwort, indem Sie ein neues Kennwort eingeben und auf Apply (Übernehmen) klicken. Notieren Sie sich das neue Kennwort und bewahren Sie die Notiz an einem sicheren Ort auf.
Page 24
ENGLISH Konfigurieren des NWA-1100s Konfigurieren der Systemeinstellungen 1. Klicken Sie in der Navigationsleiste auf SYSTEM. 2. Das Fenster SYSTEM > General (System > Allgemein) erscheint.
Page 25
DEUTSCH ENGLISH Der System Name (Systemname) identifiziert das NWA-1100 in Ihrem Netzwerk. Wählen Sie einen Namen oder belassen Sie diesen als Standard. DNS Server(s) (DNS-Server): Wenn Ihnen Ihr Internetdienstanbieter bestimmte DNS-Einstellungen (Domain Name System) vorgegeben hat, wählen Sie die Option User-Defined (Benutzerdefiniert), und geben Sie sie hier ein.
Page 26
ENGLISH Konfigurieren der Drahtloseinstellungen 1. Klicken Sie in der Navigationsleiste auf WIRELESS (Drahtlos). Das Fenster Wireless Settings (Drahtloseinstell ungen) wird angezeigt. Die Drahtlosstationen und das NWA-1100 müssen für die Drahtloskommunikation dieselbe SSID, dieselbe Kanal-ID und dieselben Verschlüsselungseinstellungen verwenden. Operation Mode (Betriebsmodus): Wählen Sie als Betriebsmodus die Option Access Point.
Page 27
DEUTSCH ENGLISH 3. Klicken Sie auf die Registerkarte Security (Sicherheit). 4. Hier können Sie die Sicherheitseinstellungen für Ihr Drahtlosnetzwerk eingeben. Je nachdem, welchen Sicherheitstyp Sie im Feld Security Mode (Sicherheitsmodus) wählen, werden andere Felder angezeigt. Wählen Sie None (Keine), wenn Sie keinen Sicherheitsmodus verwenden möchten.
Page 28
ENGLISH 5. Klicken Sie in der Navigationsleiste auf IP. Wenn Sie eine IP-Adresse haben, wählen Sie die Option Use fixed IP address (Feste IP-Adresse verwenden) und geben Sie sie zusammen mit der Subnetz- Maske und der Gateway-IP- Adresse ein. Anderenfalls wählen Sie Get automatically from DHCP...
Page 29
DEUTSCH ENGLISH Konfigurieren der IP-Einstellungen 1. Wählen Sie die IP- Adresse des NWA-1100s so, dass sie im selben Subnetz liegt wie das Netzwerk. Klicken Sie in der Navigationsleiste auf Wenn Sie möchten, dass ein DHCP-Server des Netzwerks dem NWA- 1100 eine IP-Adresse zuweist, wählen Sie Get automatically from DHCP (Automatisch vom...
Page 30
ENGLISH Wenn Sie die IP-Adresse des NWA-1100s ändern, müssen Sie beim nächsten Zugriff auf den Web-Konfigurator die neue IP-Adresse verwenden. Wenn Sie Get automatically from DHCP (Automatisch vom DHCP beziehen) wählen, müssen Sie beim DHCP-Server nachsehen, welche IP-Adresse er dem NWA-1100 zuweist. Weitere Informationen dazu finden Sie in der Dokumentation des DHCP-Servers.
Page 31
DEUTSCH ENGLISH Installieren der Hardware Anschließen der Antennen Führen Sie die nachfolgend beschriebenen Schritte aus, um die mitgelieferten Antennen anzuschließen. 1. Die Antennenanschlüsse befinden sich an beiden Seiten des NWA- 1100s. 2. Schrauben Sie die Antennen im Uhrzeigersinn in die Antennenanschlüsse.
Page 32
ENGLISH An einer Wand montiert Führen Sie die nachfolgenden Schritte aus, um das NWA-1100 an einer Wand zu montieren. 1. Schrauben Sie zwei Schrauben (nicht mitgeliefert) in einem Abstand von 60 mm in die Wand. Sie können die Zeichnung am Ende dieses Handbuchs verwenden, damit die Schraublöcher den richtigen Abstand haben.
Page 33
DEUTSCH ENGLISH 2. Richten Sie die Kabel. Führen Sie die Anschlusskabel entlang der Rückseite des NWA-1100s (siehe Abbildung). ODER: Führen Sie die Anschlusskabel nach oben entlang der Decke. 3. Richten Sie die Montagelöcher an der Rückseite des NWA- 1100s an den Schrauben in der Wand aus.
Page 34
ENGLISH Power-over-Ethernet (PoE) Einrichten (Optional) Power over Ethernet (PoE) ist die Fähigkeit, das NWA-1100 über ein 8- poliges CAT 5 Ethernet-Kabel mit Strom zu versorgen, sodass keine zusätzliche Stromquelle benötigt wird. Um das Ethernet-Kabel (A) mit Strom (C) zu versorgen, wird zudem ein Einspeise- oder PoE-Gerät (B) (nicht im Lieferumfang enthalten) benötigt.
ESPAÑOL ESPAÑOL ENGLISH Vista previa Esta Guía de instalación rápida le muestra cómo instalar y configurar el NWA1100 (marcado como Z en el ejemplo de abajo) para permitir a los clientes inalámbricos acceder de forma segura a su red inalámbrica. Vea su Guía del usuario para más información.
Page 36
ENGLISH Conectar el hardware 1. Con el cable Ethernet gris, conecte el puerto ETHERNET en un ordenador para la configuración inicial. 2. Conecte el zócalo POWER 12VDC a una toma de corriente utilizando únicamente el adaptador de corriente incluido. Conecte el puerto ETHERNET del NWA1100 a una clavija Ethernet con acceso a la red tras haber completado la configuración inicial.
Page 37
ESPAÑOL ENGLISH LEDs • El LED SYS parpadea en ámbar, luego se vuelve fijo cuando se conecta la corriente. • Uno de los LEDs del puerto ETHERNET se enciende si el puerto está correctamente conectado y parpadea cuando hay tráfico. La luz se enciende si la conexión es a 100 Mbps.
Page 38
ENGLISH Acceder al Configurador Web Utilice Internet Explorer 6.0 o superior o Netscape Navigator 7.0 o una versión superior con JavaScript activado y el bloqueo de anuncios desactivado. Configurar la dirección IP de su ordenador Apunte la configuración IP actual de su ordenador antes de cambiarla. Primero, ajuste su ordenador para utilizar una dirección IP estática dentro del rango 192.168.1.3 - 192.168.1.254 con una máscara de subred 255.255.255.0.
Page 39
ESPAÑOL ENGLISH 2. Escriba 1234 (contraseña predeterminada) en el campo Password (Contraseña) y haga clic en Login (Iniciar sesión). 3. Cambie la contraseña de acceso introduciendo una nueva contraseña y haciendo clic en Apply (Aplicar). Asegúrese de grabar la nueva contraseña y guardarla en un lugar seguro.
Page 40
ENGLISH Configure el NWA1100 Ajustar la configuración del sistema 1. Haga clic en SYSTEM (SISTEMA) en el panel de navegación. 2. Aparecerá la pantalla SYSTEM > General.
Page 41
ESPAÑOL ENGLISH System Name (Nombre del sistema) es para identificar el NWA1100 en su red. Elija un nombre identificativo o deje el predeterminado. DNS Server(s) (Servidor(es) DNS): Si su ISP le ha facilitado una configuración DNS (Domain Name System) específica, seleccione User- Defined (Definido por el usuario) y escríbala aquí.
Page 42
ENGLISH Ajustar la configuración inalámbrica 1. Haga clic en WIRELESS (INALÁMBRICO ) en el panel de navegación. Aparecerá la pantalla Wireless Settings (Configuración inalámbrica). Las estaciones inalámbricas y el NWA1100 deben utilizar la misma configuración SSID, ID de canal y cifrado para la comunicación inalámbrica.
Page 43
ESPAÑOL ENGLISH 3. Haga clic en la ficha Security (Seguridad). Aquí es donde puede introducir la configuración de seguridad para su red inalámbrica. Los campos que rellene se diferencian según el tipo de seguridad que seleccione en el campo Security Mode (Modo de seguridad).
Page 44
ENGLISH Ajustar la configuración IP 1. Necesita configurar la dirección IP de su NWA1100 para que estén en la misma subred que su red. Haga clic en IP en el panel de navegación. Seleccione Get automatically from DHCP (Obtener automáticamente de DHCP) si desea que un servidor DHCP de su red asigne una dirección IP al...
Page 45
ESPAÑOL ENGLISH Si cambia la dirección IP de su NWA1100, deberá utilizar la nueva dirección IP la próxima vez que acceda al configurador Web. Si selecciona Get automatically from DHCP (Obtener automáticamente de DHCP) compruebe que su servidor DHCP determina la dirección IP que asigna al NWA1100.
Page 46
ENGLISH Instalar el Hardware Conectar las antenas Siga estos pasos para conectar las antenas incluidas. 1. Localice los conectores de la antena en los laterales de su NWA1100. 2. Atornille las antenas en sentido horario en los conectores para antenas. Las antenas deberían estar perpendiculares al suelo y paralelas entre ellas.
Page 47
ESPAÑOL ENGLISH Siga estos pasos para montar su NWA1100 en una pared. 1. Localice una posición alta en la pared libre de obstáculos. 2. Conecte dos tornillos (no incluidos) en la pared separados por 60mm. Puede usar el diagrama al final de esta guía para ayudarle a marcar los agujeros de los tornillos correctamente.
Page 48
ENGLISH 3. Ajuste los cables. Pase los cables de conexión por la parte posterior del NWA1100 hacia abajo como aparece en la siguiente figura. Pase los cables de conexión por la parte posterior hacia arriba o por el borde del techo. 4.
Page 49
ESPAÑOL ENGLISH Corriente sobre Ethernet (opcional) La Corriente sobre Ethernet (PoE) es la capacidad de suministrar alimentación a su NWA1100 a través de un cable Ethernet CAT 5 de 8 contactos, eliminando la necesidad de una toma de corriente cercana. También necesitará...
FRANÇAIS FRANÇAIS ENGLISH Présentation Ce guide de mise en route rapide indique comment installer et configurer le NWA1100 (marqué d'un Z dans l'exemple ci-dessous) pour permettre aux clients sans fil d’accéder en toute sécurité à votre réseau câblé. Consultez votre Guide de l'utilisateur pour plus d'informations. Vous aurez peut-être besoin de vos informations d'accès à...
Page 52
ENGLISH Connecter le matériel 1. Utilisez le câble Ethernet gris, connectez le port ETHERNET à un ordinateur pour effectuer la configuration initiale. 2. Connectez la prise POWER 12VDC à une source de courant en utilisant uniquement l’adaptateur d’alimentation fourni. Connectez le port ETHERNET du NWA1100 à une prise Ethernet avec accès au réseau après avoir terminé...
Page 53
FRANÇAIS ENGLISH • La LED SYS clignote couleur ambre, puis reste allumée en vert quand l'alimentation est connectée. • Une des LED par port le ETHERNET s'allume si le port est correctement connecté, et clignote quand il y a du trafic. Le voyant ambre s'allume si la connexion est à...
Page 54
ENGLISH Accéder au configurateur Web Utilisez Internet Explorer 6.0 et plus récent ou Netscape Navigator 7.0 et des versions plus récentes avec JavaScript activé et le bloqueur de fenêtres publicitaires intempestives désactivé. Paramétrez l'adresse IP de votre ordinateur Notez les paramètres IP actuels de votre ordinateur avant de les modifier.
Page 55
FRANÇAIS ENGLISH 2. Cliquez sur Login (Ouvrir une session) (le mot de passe par défaut 1234 est déjà entré). 3. Changez le mot de passe d'ouverture de session en entrant un nouveau mot de passe et cliquez sur Apply (Appliquer). Prenez soin d'enregistrer le nouveau mot de passe et conservez-le dans un endroit sûr.
Page 56
ENGLISH Configurer le NWA1100 Configurer les paramètres du système 1. Cliquez sur System (SYSTÈME) dans le panneau de navigation. 2. L'écran System (SYSTÈME) > General (Général) apparaît.
Page 57
FRANÇAIS ENGLISH System Name (Nom du système) sert à identifier le NWA1100 sur votre réseau. Choisissez un nom distinctif, ou laissez celui-ci à sa valeur par défaut. DNS Server(s) (Serveur(s) DNS): Si votre FAI vous a attribué des paramètres DNS (Domain Name System) spécifiques, sélectionnez User-Defined (Personnalisé) et entrez-les ici.
Page 58
ENGLISH Configurer les paramètres sans fil 1. Cliquez sur WIRELESS (SANS FIL) dans le panneau de navigation. L'écran Wireless Settings (Paramètres sans fil) s'affiche. Les stations sans fil et le NWA1100 doivent utiliser le même SSID, ID de canal et paramètres de cryptage pour la communication sans fil. Operation Mode (Mode de fonctionnement): Vérifiez que Access Point (le mode Point d'accès) est sélectionné.
Page 59
FRANÇAIS ENGLISH 3. Cliquez sur l’onglet Security (Sécurité). 4. C'est l'endroit où vous pouvez enter les paramètres de sécurité pour votre réseau sans fil. Les champs que vous avez remplis diffèrent en fonction des types de sécurité que vous sélectionnez dans le champ Security Mode (Mode Sécurité).
Page 60
ENGLISH Configurer les paramètres IP 1. Vous devez paramétrer l'adresse IP de votre NWA1100 afin qu'elle se trouve dans le même masque de sous-réseau que votre réseau. Cliquez sur IP dans le panneau de navigation. Sélectionnez Get automatically from DHCP (Obtenir automatiquement à...
Page 61
FRANÇAIS ENGLISH Si vous changez l’adresse IP du NWA1100, vous devrez utiliser la nouvelle adresse IP la prochaine fois que vous accéderez au configurateur web. Si vous sélectionnez Get automatically from DHCP (Obtenir automatiquement à partir de DHCP), consultez votre serveur DHCP pour déterminer l'adresse IP qu'il a attribuée au NWA1100.
Page 62
ENGLISH Installer le matériel Connecter les antennes 1. Localisez les connecteurs des antennes sur les côtés de votre NWA1100. 2. Vissez les antennes dans le sens des aiguilles d’une montre sur les connecteurs de l’antenne. Les antennes doivent être perpendiculaires au sol et parallèles entre elles.
Page 63
FRANÇAIS ENGLISH 1. Installez deux vis (non fournies) dans le mur à 60 mm l’une de l’autre. Vous pouvez utiliser le schéma à la fin de ce guide pour vous aider à marquer correctement les trous de vis. Utilisez des vis de 6mm ~ 8mm (0,24"...
Page 64
ENGLISH 2. Ajustez les câbles. Faites passer les câbles de connexion derrière le dos du NWA1100 comme indiqué sur l’image suivante. OU : Faites passer les câbles de connexion vers le haut et le long du bord du plafond. 3. Alignez les trous au dos du NWA1100 avec les vis sur le mur.
Page 65
FRANÇAIS ENGLISH Installer l’Alimentation Électrique par Câble Ethernet (PoE) (Facultative) PoE (Power over Ethernet) est la possibilité de fournir l’alimentation à votre NWA1100 via un câble Ethernet CAT 5 8 broches, éliminant la nécessité d’une prise courant proche. Un injecteur ou matériel PoE (B) (non fourni) est aussi requis pour alimenter (C) le câble Ethernet (A).
ITALIANO ITALIANO ENGLISH Cenni generali La presente guida introduttiva fornisce informazioni sull'impostazione e la configurazione di NWA1100 (contrassegnato Z nell'esempio sotto) per consentire ai clienti wireless di accedere in modo sicuro alla rete cablata. Consultare la propria Guida utente per ulteriori informazioni. È...
Page 68
ENGLISH Collegamento dell'hardware 1. Per mezzo del cavo Ethernet grigio, collegare la porta ETHERNET ad un computer per la configurazione iniziale. 2. Collegare la porta POWER 12VDC a una sorgente di alimentazione utilizzando esclusivamente l'alimentatore fornito in dotazione. Collegare la porta ETHERNET di NWA1100 a un jack Ethernet con accesso alla rete dopo aver completato la configurazione iniziale.
Page 69
ITALIANO ENGLISH • Quando l'alimentazione è collegata, il LED SYS lampeggia di colore arancione e resta acceso di colore verde. • Uno dei LED sulla porta ETHERNET di accende se la porta è correntemente collegata, lampeggiando quando c'è traffico dati. La luce arancione si accende se la connessione è...
Page 70
ENGLISH Accedere allo strumento di configurazione Web Utilizzare Internet Explorer 6.0 o versione successiva oppure Netscape Navigator 7.0 o versione successiva con JavaScript abilitato e bloccaggio dei pop-up disabilitato. Impostare l'indirizzo IP del computer Annotare le impostazioni IP correnti del computer prima di cambiarle. Configurare dapprima il computer a utilizzare un indirizzo IP statico nell'intervallo 192.168.1.3 - 192.168.1.254 con una subnet mask uguale a 255.255.255.0.
Page 71
ITALIANO ENGLISH 2. Immettere 1234 (la password predefinita) nel campo Password e scegliere Login (accedi). 3. Cambiare la password di accesso immettendo una nuova password e facendo clic su Appy (applica). Registrare la nuova password e conservarla in un luogo sicuro. Se la password viene cambiata e la si dimentica, sarà...
Page 72
ENGLISH Configurare NWA1100 Configura le impostazioni del sistema 1. Fare clic su SYSTEM (SISTEMA) nel pannello di navigazione. 2. Appare la schermata SYSTEM (SISTEMA) > Genera (Generale).
Page 73
ITALIANO ENGLISH System Name (nome sistema) consente di identificare NWA1100 sulla rete. Scegliere un nome distintivo o lasciare quello predefinito. DNS Server(s) (Server DNS): se l'ISP fornisce impostazioni DNS (Domain Name System) specifiche, scegliere User-Defined (definite dall'utente) ed immettere qui tali impostazioni. 3.
Page 74
ENGLISH Configura impostazioni Wireless 1. Fare clic su WIRELESS (WIRELESS) nel pannello di navigazione. Viene visualizzata la schermata Wireless Settings (impostazioni wireless). Le stazioni wireless e NWA1100 devono utilizzare lo stesso SSID, ID di canale e impostazione di crittografia per consentire la comunicazione wireless.
Page 75
ITALIANO ENGLISH 3. Fare clic sulla scheda Security (Sicurezza). In questo campo è possibile immettere le impostazioni di sicurezza della rete wireless. I campi compilati variano a seconda del tipo di sicurezza selezionata nel campo Security Mode (Modalità di sicurezza). Selezionare None (Nessuno) se non si desidera utilizzare la sicurezza wireless.
Page 76
ENGLISH Configura impostazioni IP 1. È necessario impostare l'indirizzo IP di NWA1100 per essere nella stessa subnet della rete. Fare clic su IP nel pannello di navigazione. Selezionare Get automatically from DHCP (ottieni automaticamente da DHCP) per consentire a un server DHCP presente in rete di assegnare un indirizzo IP a NWA1100.
Page 77
ITALIANO ENGLISH Se si cambia l'indirizzo IP di NWA1100, è necessario utilizzare il nuovo indirizzo IP quando si desidera accedere allo strumento di configurazione Web. Selezionando Get automatically from DHCP (ottieni automaticamente da DHCP), controllare il server DHCP per determinare l'indirizzo IP assegnato a NWA1100. Per ulteriori informazioni vedere la documentazione del server DHCP.
Page 78
ENGLISH Installazione dell'hardware Collegamento delle antenne Seguire le istruzioni presentate di seguito per eseguire il collegamento alle antenne in dotazione. 1. Individuare le prese delle antenne presso i lati di NWA1100. 2. Individuare le prese delle antenne presso i lati di NWA1100. Le antenne devono essere perpendicolari al suolo e parallele una con l’altra.
Page 79
ITALIANO ENGLISH Seguire i seguenti punti per applicare NWA1100 ad una parete. 1. Individuare una posizione elevata sul muro che sia esente da ostacoli. 2. Inserire due viti (non in dotazione) nella parete a 60 mm si distanza. È possibile utilizzare lo schema al termine della presente guida per facilitare il contrassegno dei fori delle viti.
Page 80
ENGLISH 3. Regolare i cavi. Far scorrere i cavi di collegamento lungo la parte posteriore di NWA1100 come mostrato nella figura seguente. oppure far scorrere i cavi di collegamento verso l’alto e lungo il bordo della parte superiore. 4. Allineare i fori presso la parte posteriore di NWA1100 con le viti sulla parete.
Page 81
ITALIANO ENGLISH Configurazione di Power over Ethernet (opzionale) Power over Ethernet (PoE) consente di fornire elettricità a NWA1100 per mezzo di un cavo Ethernet CAT 5 a 8 poli, eliminando la necessità di disporre di una sorgente di alimentazione nelle vicinanze. Un iniettore o un dispositivo PoE (B) (non in dotazione) è...
РУССКИЙ РУССКИЙ ENGLISH Обзор В кратком руководстве пользователя будет рассказано, как подключить и настроить NWA1100 (помеченный Z в приведенном ниже примере) для безопасного доступа беспроводных клиентов к проводной сети. Обратитесь к полной версии руководства для получения дополнительной информации. Вам может понадобиться ваша информация для доступа к сети Интернет.
Page 84
ENGLISH Подключение оборудования 1. При помощи кабеля Ethernet подключите порт ETHERNET к вашему компьютеру, чтобы получить возможность конфигурировать устройство. 2. Подключите питание к разъему POWER 12VDC, используя для этого входящий в комплект поставки сетевой адаптер. После выполнения начальной настройки подключите порт ETHERNET вашего...
Page 85
РУССКИЙ ENGLISH Светодиодные индикаторы • При подключении питания индикатор SYS должен вначале мигать желтым светом, а затем постоянно светиться зеленым светом. • Один из индикаторов на порте ETHERNET включается при правильном подключении и начинает мигать при передаче данных. Желтый индикатор светится при подключении на скорости 100 Мбс. Зеленый...
Page 86
ENGLISH Доступ к веб-конфигуратору Используйте Internet Explorer версии 6.0 и выше или Netscape Navigator версии 7.0 и выше с активированным JavaScript и отключенной блокировкой всплывающих окон. Установка IP-адреса вашего компьютера Запишите текущие настройки IP вашего компьютера перед их изменением. Вначале установите на вашем компьютере использование статического IP-адреса...
Page 87
РУССКИЙ ENGLISH 2. Введите 1234 (пароль по умолчанию) в поле Password (Пароль) и щелкните на кнопке Login (Вход). 3. Измените пароль входа в систему, введя новый, и нажмите на Apply (Применить). Запишите новый пароль и храните его в надежном месте. Если...
Page 88
ENGLISH Конфигурирование NWA1100 Настройка системных параметров 1. Щелкните на SYSTEM (СИСТЕМА) на панели навигации. 2. Появится окно SYSTEM (СИСТЕМА) > General (Общие).
Page 89
РУССКИЙ ENGLISH System Name (Системное имя) используется для идентификации NWA1100 в вашей сети. Введите необходимое имя устройства, или оставьте предложенное по умолчанию. DNS Server(s) (DNS сервер(ы)): Если ваш провайдер предоставил вам определенную настройку DNS (Система доменных имен), выберите User-Defined (Определяется пользователем) и введите предоставленное...
Page 90
ENGLISH Настройка параметров беспроводной сети 1. Щелкните на WIRELESS (БЕСПРОВОДН АЯ СЕТЬ) на панели навигации. Появится окно Wireless Settings (Настройки беспроводной сети). Для успешного соединения беспроводная станция и NWA1100 должны иметь одинаковые SSID, идентификатор канала и настройки шифрования. Operation Mode (Режим работы): Убедитесь, что выбран режим AP (Точка...
Page 91
РУССКИЙ ENGLISH 3. Щелкните на вкладке Security (Безопасность) Здесь вы можете ввести настройки безопасности вашей беспроводной сети. Вносимые вами изменения в настройки должны соответствовать типу безопасности, выбранному в поле Security Mode (Режим безопасности). Выберите None (Нет) если вы не хотите использовать беспроводную безопасность. В...
Page 92
ENGLISH Конфигурирование настроек IP 1. Вы должны установить на вашем NWA1100 IP- адрес с маской подсети вашей сети. Щелкните на IP на навигационной панели. Выберите Get automatically from DHCP (Получать автоматически от DHCP) если вы хотите, чтобы IP-адрес для вашего NWA1100 предоставлял...
Page 93
РУССКИЙ ENGLISH Если вы изменяете IP-адрес NWA1100, следует использовать именно его для дальнейшего конфигурирования. Если вы выбираете Get automatically from DHCP (Получать автоматически от DHCP), проверьте назначение DHCP- сервером IP-адреса для NWA1100. Дополнительные сведения приведены в документации к серверу DHCP. 2.
Page 94
ENGLISH Установка оборудования Подключение антенн 1. Закручивайте антенны по часовой стрелке в разъемы по бокам NWA1100. Антенны должны располагаться вертикально и параллельно друг одругу. Убедитесь, что они закреплены надежно. Монтаж оборудования Лучше всего устанавливать точку доступа в центре зоны, в которой необходимо...
Page 95
РУССКИЙ ENGLISH 1. Ввинтите в стену два шурупа (не поставляются) на расстоянии 60 мм друг от друга (см. схему в шаге 3). Используйте шурупы с шириной головки 6мм ~ 8мм. Не вкручивайте шурупы до упора, оставьте промежуток между головкой шурупа и стеной. Этот...
Page 96
ENGLISH 2. Подключите кабели. Пропустите соединительные кабели сзади NWA1100 как показано на иллюстрации ниже. ЛИБО: Пропустите соединительные кабели вверх и проложите их вдоль потолка. 3. Совместите отверстия на задней части NWA1100 с шурупами в стене. Подвесьте NWA1100 на шурупах.
Page 97
РУССКИЙ ENGLISH Настроить подачу питания через Ethernet (при необходимости) Питание через Ethernet (PoE) - это возможность обеспечения вашего NWA1100 питанием через 8-жильный кабель CAT 5 Ethernet, при использовании которого нет необходимости в источнике питания. Для подведения питания к кабелю Ethernet вам также понадобится инжектор...
SVENSKA SVENSKA ENGLISH Översikt Denna snabbstartguide visar hur du installerar och konfigurerar NWA1100 (märkt Z i exemplet nedan) så att trådlösa klienter kan få åtkomst till ditt nätverk på ett säkert sätt. Se bruksanvisningen för mer information. Eventuellt behöver ha tillgång till uppgifterna för din Internet uppkoppling.
Page 100
ENGLISH Ansluta maskinvara 1. Använd den grå Ethernet-kabeln och anslut ETHERNET-porten till en dator för inledande konfiguration. 2. Anslut uttaget POWER 12VDC till en strömkälla. Använd enbart den medföljande strömadaptern. Anslut NWA1100s ETHERNET-port till ett Ethernet-uttag med nätverksåtkomst när du har slutfört den inledande konfigurationen.
Page 101
SVENSKA ENGLISH Indikatorlampor • SYS-lampan blinkars orange, och lyser sedan stadigt grön när strömmen är ansluten. • En av indikatorlamporna vid porten ETHERNET tänds om porten är rätt ansluten, och blinkar vid trafik. Den orange lampan lyser om anslutningen sker med 100 Mbps. Den gröna lampan lyser om anslutningen sker med 10 Mbps.
Page 102
ENGLISH Få åtkomst till webbkonfigurator Använd Internet Explorer version 6.0 eller senare eller Netscape Navigator version 7.0 eller senare med JavaScript aktiverat och popup- blockering inaktiverad. Ställa in datorns IP-adress Skriv ner datorns befintliga IP-inställningar innan du ändrar dem. Först måste du ställa in datorn att använda en statisk IP-adress i intervallet 192.168.1.3 - 192.168.1.254 och sätt subnetmask på...
Page 103
SVENSKA ENGLISH 2. Ange 1234 (standardlösenordet) i fältet Password (lösenord) och klicka på Login (logga in). 3. Ändra inloggningslösenordet genom att ange ett nytt lösenord och klicka på Apply (verkställ). Var noga med att anteckna det nya lösenordet och att förvara det på ett säkert ställe.
Page 104
ENGLISH Konfigurera NWA1100 Konfigurera systeminställningar 1. Klicka på SYSTEM i navigationspanelen. SYSTEM > General (system - allmänt) visas. Skärmbilden...
Page 105
SVENSKA ENGLISH System Name (systemnamn) identifierar NWA1100 i ditt nätverk. Välj ett namn, eller låt standardnamnet stå kvar. beskrivande Domain Name (domännamn): Ange ett domännamn om din Internet- leverantör (ISP) fordrar ett sådant för autentisering. I annat fall kan du låta detta vara tomt eller ställa in det på...
Page 106
ENGLISH Konfigurera trådlösa inställningar 1. Klicka på WIRELESS (trådlös) i navigationspanel en. Följande skärm visas. Alla fält är inte tillgängliga för alla modeller. De trådlösa stationerna och NWA1100 måste använda samma SSID, kanal-ID och krypteringsinställningar för trådlös kommunikation. Operation Mode (driftläge): Kontrollera att läget Access Point (accesspunkt) är valt.
Page 107
SVENSKA ENGLISH 3. Klicka på fliken Security (säkerhet). Kontrollera att Security01 är valt och klicka på Edit (redigera). Här kan du ange säkerhetsinställningar för ditt trådlösa nätverk. Vilka fält du fyller i beror på vilken typ av säkerhet du valt i fältet Security Mode (säkerhetsläge).
Page 108
ENGLISH Konfigurera IP-inställningar 1. Du måste ställa in NWA1100s IP-adress på samma subnet som ditt nätverk. Klicka på IP i navigationspanelen. Välj Get automatically from DHCP (hämta automatiskt från DHCP) om du vill låta en DHCP- server i ditt nätverk tilldela en IP-adress till NWA1100.
Page 109
SVENSKA ENGLISH Om du ändrar NWA1100s IP-adress, måste du använda den nya IP- adressen nästa gång du vill få åtkomst till webbkonfiguratorn. Om du väljer Get automatically from DHCP (hämta automatiskt från DHCP), kontrollera din DHCP-server för att avgöra vilken IP-adress den tilldelar till NWA1100.
Page 110
ENGLISH Installera maskinvaran Ansluta antenner 1. Skruva fast antennerna medsols på antennanslutningarna på sidorna av NWA1100. Antennerna ska placeras lodrätt mot marken och vara parallella med varandra. Kontrollera att antennerna är säkert fastskruvade på antennanslutningarna. Montera maskinvara I allmänhet ligger den bästa placeringen för åtkomstpunkten i centrum av det avsedda trådlösa täckningsområdet.
Page 111
SVENSKA ENGLISH 1. Skruva in två skruvar (medföljer inte) i väggen med 60 mm avstånd (se figuren i steg 3). Använd skruvar med 6-8 mm breda huvuden. Skruva inte in skruvarna hela vägen i väggen; lämna kvar ett litet utrymme mellan skruvhuvud och vägg.
Page 112
ENGLISH 2. Justera sladdarna. Dra anslutningssladdarna nerför baksidan på NWA1100 enligt följande figur. ELLER: Dra anslutningssladdarna uppåt och längs innertakets kant. 3. Passa in hålen på baksidan av NWA1100 med skruvarna i väggen. Häng NWA1100 på skruvarna.
Page 113
En PoE-injektor (medföljer inte) behövs också för att förse Ethernet-kabeln med ström. Denna funktion ger ökad flexibilitet vid placering av NWA1100. I följande figur är Z din NWA1100, A är CAT 5 Ethernet-sladden, B är PoE- injektorn och C är strömsladden. Mer produkthjälp finns på http://www.support.zyxel.se.
Page 117
简体中文 ENGLISH 指示灯 • 当连接电源时,SYS LED 呈琥珀色闪烁,然后保持在绿色。 • 如果以太网端口连接正确,端口旁的 LED 之一会亮起,并且在有流量时 闪烁。如果连接处于 100 Mbps 下,琥珀色灯发光。如果连接处于 10 Mbps 下,绿色灯发光。 如果以太网端口附近无 LED 亮起,请检查端口电缆连接。确定您 的计算机网卡工作正常。...
Page 118
ENGLISH 访问 Web 配置程序 请使用 Internet Explorer 6.0 以上版本或 Netscape Navigator 7.0 以上版 本,并启动 JavaScript 和关闭弹出窗口阻止功能。 设置计算机的 IP 地址 更改计算机目前的 IP 设置之前,请先将其记下。 首先,设置计算机使用介于 192.168.1.3 - 192.168.1.254 之间的静态 IP 地 址,并将子网掩码设为 255.255.255.0。这项操作可以确保您的计算机和 NWA1100 设备通讯。请参阅 《使用手册》 ,获得设置计算机 IP 地址的相关 信息。 登录到 Web 配置程序 尽管也可以无线连接到...
Page 124
ENGLISH 配置 设置 1. 您需要将NWA1100的 IP 地址设置为与您的网络位 于相同子网络。单击导航 窗格中的 IP。 如果您要让网络上的 DHCP 服务器为 NWA1100 配置 IP 地址, 请选择 Get automatically from DHCP ( 自动从 DHCP 获 得 )。 如果已有预定要使用的特 定 IP 地址,请选择 Use fixed IP address ( 使用 固定 IP 地址 ),并输入 该...
Page 137
繁體中文 ENGLISH 設定 IP 設定 1. 您需要將NWA1100的 IP 位址設定為與您的網路位 在相同子網路。按一下導 覽面板中的 IP。 如果您要讓網路上的 DHCP 伺服器為 NWA1100 配置 IP 位址, 請選取 Get automatically from DHCP ( 自動從 DHCP 取 得 )。 如果已有預定要使用的特 定 IP 位址,請選取 Use fixed IP address ( 使用固 定...
Page 138
ENGLISH NWA1100 現已準備就緒,可以連接至交換器或路由器。您可以立即進行此項 作業,或是等安裝天線掛載 NWA1100 之後再進行。 NWA1100 NWA1100 使用的 IP 位址 如果 無法與網路通訊 , 請確定 與交換器 / 路由器位於相同的子網路。...
Page 143
• Select your product from the drop-down list • Gehen Sie auf www.zyxel.com. • Vaya a www.zyxel.com. box on the ZyXEL home page to go to that • Wählen Sie Ihr Produkt aus der Auswahlliste • Seleccione el producto que desea en el product's page.