Page of 228
Also See for TE-7000S:
Service manual - 3 pages
User's manual - 112 pages
TE-7000S/8000F/8500F
Electronic Cash Register
————————————————————————
Programming Manual
Version
1.0 February 2003
Coffee
§∞∏©ºß 12 ST
0.00
R
$8.00
$76.50
0.00
0.00
0.00
c

   Also See for CASIO TE-7000S

   Summary of Contents for CASIO TE-7000S

  • Page 1

    TE-7000S/8000F/8500F Electronic Cash Register ———————————————————————— Programming Manual Version 1.0 February 2003 0.00 0.00 Coffee $8.00 §∞∏©ºß 12 ST $76.50 0.00 0.00...

  • Page 2

    The information contained in this document is subject to change without notice. CASIO Computer Co., Ltd. makes no warranty of any kind with regard to this material, including, but not limited to the implied warranties of marketability and fitness for a particular purpose.

  • Page 3

    Preface TE-7000S/8000F/8500F Programming Manual...

  • Page 4: Table Of Contents

    Contents 1. Machine Initialization ..............P-8 1-1. How to initialize the terminal ..............P-8 1-2. How to initialize the terminal (add / replace one terminal) ....... P-11 1-3. How to flag clear the terminal (or INIT2) ..........P-11 2. Program 5 ................P-14 2-1.

  • Page 5: Table Of Contents

    5-3-3 Programming order character link ............P-155 5-3-4 Programming fixed totalizer descriptors ...........P-156 5-3-5 Programming group character ..............P-157 5-3-6 Programming special characters ..............P-157 5-3-7 Programming report headers ..............P-159 5-3-8 Programming endorsement message ............P-160 5-3-9 Programming GT character ..............P-160 TE-7000S/8000F/8500F Programming Manual...

  • Page 6: Table Of Contents

    Contents 6. Program 1 ................P-162 6-1. Presetting date and time ................P-162 6-2. Programming unit price and rate............P-163 6-2-1 Programming PLU unit price ..............P-163 6-2-2 Programming PLU 2nd unit price .............P-164 6-2-3 Programming PLU unit price and PLU 2nd unit price.......P-165 6-2-4 Programming subdepartment unit price ...........P-166 6-2-5 Programming department unit price ............P-166 6-2-6 Programming PLU / PLU 2nd@ / subdepartment...

  • Page 7: Te-7000s/8000f/8500f Programming Manual

    1. Machine Initialization ..............P-8 1-1. How to initialize the terminal ..............P-8 1-2. How to initialize the terminal (add / replace one terminal) ......P-11 1-3. How to flag clear the terminal (or INIT2) ........... P-11 TE-7000S/8000F/8500F Programming Manual...

  • Page 8: Machine Initialization, How To Initialize The Terminal, Machine Initialization, How To Initialize The Terminal

    Initialization 1. Machine Initialization 1-1. How to initialize the terminal Preparation: 1. All peripheral devices and terminals of this cluster should be turned off. 2. Connect all of the peripheral devices (such as printer, display etc.) to terminal. 3. Connect all terminals by inline. Operation: 4.

  • Page 9

    If you don't need to download any program data, just select “1. No Restore / Receive” and press the <YES> key. If you have another machine to initialize, return to step 4. TE-7000S/8000F/8500F Programming Manual...

  • Page 10

    Initialization Restore from CF card. 15. Insert the CF card into the slot and select the appropriate file and press the <YES> key. 16. After the confirmation window is shown, press the <YES> key to proceed restoring. After completion of downloading, return to step 4 to initialize other terminals.

  • Page 11: How To Initialize The Terminal (add / Replace One Terminal)

    “Copyright” window is shown. 6. After releasing the key, press the <ST> key. 7. Select “1. Flag Clear” and press the <YES> key. 0.00 The flag clear operation is finished. Note: Performing “Init 2” requires password “8888888888” and <YES>. TE-7000S/8000F/8500F Programming Manual P-11...

  • Page 12

    Initialization P-12...

  • Page 13

    2. Program 5 ................. P-14 2-1. Programming memory allocation (daily & program) ......... P-14 2-2. Programming memory allocation (periodic & work) ......... P-15 2-3. Programming memory allocation file by file ..........P-16 TE-7000S/8000F/8500F Programming Manual P-13...

  • Page 14: Program 5, Programming Memory Allocation (daily & Program)

    Program 5 2. Program 5 2-1. Programming memory allocation (daily & program) Operation: 1. Sign on a clerk (if necessary). 2. Press <PGM MODE> repeatedly or “5” <PGM MODE> to assign Program 5 mode. 0.00 3. Press the <YES> key. 0.00 4.

  • Page 15: Programming Memory Allocation (periodic & Work)

    <NO> (not allocate) key. 6. Press the <ESC> key to return to the previous menu. Note: The Flag Clear operation resets “YES” status. However it does not reallocate the files that were already allocated on this screen. TE-7000S/8000F/8500F Programming Manual P-15...

  • Page 16: Programming Memory Allocation File By File

    Program 5 2-3. Programming memory allocation file by file If you want to allocate files file by file, follow the procedures below. Operation: 1. Sign on a clerk (if necessary). 2. Press <PGM MODE> repeatedly or “5” <PGM MODE> to assign Program 5 mode.

  • Page 17

    Buffer Hourly sales Sales (periodic total 1) Sales (periodic total 2) Sales (daily consolidation) for master Sales (periodic 1 consolidation) for master Sales (periodic 2 consolidation) for master Sales (consolidation work) for master Buffer TE-7000S/8000F/8500F Programming Manual P-17...

  • Page 18

    Program 5 File Record Max. No. Default Work Attribu- Allocat- File description Description length of records rec No. size tion able Monthly sales Sales (periodic total 1) Sales (periodic total 2) Sales (daily consolidation) for master Sales (periodic 1 consolidation) for master Sales (periodic 2 consolidation)

  • Page 19

    Graphic logo (internal printer) Program Watermark Program Euro program Program Arrangement Arrange group (1) 9999 Program Arrange group (2) 9999 Program Arrange group (3) 9999 Program Arrange group (4) 9999 Program Arrange group (5) 9999 Program TE-7000S/8000F/8500F Programming Manual P-19...

  • Page 20

    Program 5 P-20...

  • Page 21

    3. Program 4 ................. P-22 3-1. Programming key allocation ..............P-22 3-2. Programming key allocation (key location change) ........P-24 3-3. Programming key allocation ..............P-27 TE-7000S/8000F/8500F Programming Manual P-21...

  • Page 22: Program 4, Programming Key Allocation

    Program 4 3. Program 4 3-1. Programming key allocation Operation: 1. Sign on a clerk (if necessary). 2. Put the first level menu sheet on the keyboard. 3. Press <PGM MODE> repeatedly or “4” <PGM MODE> to assign Program 4 mode . 0.00 ∞...

  • Page 23

    Tax exempt NEW CHK New check Text print CHAR NEW/OLD New / Old check Text recall TRAY TTL NRMRCT Normal receipt Tray total No sale Non-add Validation #/NS Non-add / No sale X/Z MODE X/Z mode TE-7000S/8000F/8500F Programming Manual P-23...

  • Page 24: Programming Key Allocation (key Location Change)

    Program 4 3-2. Programming key allocation (key location change) Operation: 1. Sign on a clerk (if necessary). 2. Press <PGM MODE> repeatedly or “4” <PGM MODE> to assign Program 4 mode. 0.00 3. Press the <YES> key. 0.00 4. Select “2. Key Move” and press the <YES> key. 0.00 5.

  • Page 25

    RECEIPT ON/OFF MODE MODE MODE ON/OFF RECEIPT JOURNAL MENU VOID /SKIP FEED FEED RECEIPT OPEN PRICE LIST# MEDIA TABLE CHK/ COVERS CHANGE TRANS TEND PAGE NEW/OLD % – – HOME SUBTOTAL PAGE • CANCEL DOWN TEND TE-7000S/8000F/8500F Programming Manual P-25...

  • Page 26

    Program 4 TE-8000F CLK1 CLK2 CLK3 CLK4 CLK5 RECEIPT X / Z DISP ON/OFF MODE MODE MODE ON/OFF RECEIPT JOURNAL ESC/ FEED FEED SKIP PAGE RECEIPT OPEN – MENU HOME PAGE % – DOWN VOID CANCEL CHK/ TEND NEW/OLD SUBTOTAL •...

  • Page 27: Programming Key Allocation

    (in 3-digits) and press the corresponding key on the 0.00 appropriate menu sheet. In case of presetting flat-PLU, you can enter random PLU code instead of record No. 6. Press the <ESC> key to return to the previous menu. TE-7000S/8000F/8500F Programming Manual P-27...

  • Page 28

    Program 4 Method 2 Operation: In case of allocating different functions from the functions of the same location on the first level menu sheet, turn the menu sheet or press the <MENU> key and allocate the function on the menu sheet which you want to put. 1.

  • Page 29

    Programming auto program control .............. P-77 4-1-20 Programming LCD color control..............P-78 4-1-21 Programming Australian GST control ............P-81 4-2. Programming clerks ................. P-82 4-2-1 Programming clerk features ................P-82 4-2-2 Programming operation ................P-84 4-2-2-1 Programming clerk control ................P-84 TE-7000S/8000F/8500F Programming Manual P-29...

  • Page 30

    Program 3 4-2-2-2 Programming menu shift / 2nd@ ..............P-85 4-2-2-3 Programming mode control................P-86 4-2-2-4 Programming function control 1 ..............P-87 4-2-2-5 Programming function control 2 ..............P-88 4-2-2-6 Programming function control 3 ..............P-89 4-2-2-7 Programming function control 4 ..............P-90 4-2-2-8 Programming function control 5 ..............

  • Page 31

    4-3-7-44 Worksheet for recall ..................P-136 4-3-7-45 Worksheet for menu shift ................P-136 4-3-8 Programming shift PLU program ..............P-137 4-3-9 Programming scanning PLU link program ..........P-138 4-3-10 Programming PLU by Pulldown group ............P-140 TE-7000S/8000F/8500F Programming Manual P-31...

  • Page 32: Program 3, Programming Machine Features

    Program 3 Program 3 4-1. Programming machine features Preparation: 1. Sign on a clerk (if necessary). 2. Press <PGM MODE> repeatedly or “3” <PGM MODE> to assign Program 3 mode. 0.00 3. Select “1. Machine Feature” and press the <YES> key. 4-1-1 Programming pulldown group (adding / modifying / deleting group item) Operation...

  • Page 33

    Press <. (decimal point)> key, enter a few characters and press the <YES> key. 0.00 The terminal searches the item begins with these characters. After character search, press <RIGHT ARROW> / <LEFT ARROW> shows the next/previous candidate. TE-7000S/8000F/8500F Programming Manual P-33...

  • Page 34: Programming Set Menu Table

    Program 3 Deletion 0.00 7. Select the first record of items you want to delete and press the <NO> key. 0.00 8. Press the <YES> key. The selected item and followings are deleted. 9. Press the <ESC> key to return to the previous menu. 4-1-2 Programming set menu table Operation...

  • Page 35

    11. Press the <YES> key to show the PLU / List table list. 12. Select the main PLU/LIST by pressing the appropriate <Flat PLU>, entering PLU code and <PLU>, pressing <LIST> or entering List No. and <LIST-#>. 13. Press the <ESC> key to terminate this procedure. 0.00 TE-7000S/8000F/8500F Programming Manual P-35...

  • Page 36: Programming Arrangement

    Program 3 Deletion 0.00 6. Select the first record of items you want to delete and press the <NO> key. 0.00 7. Press the <YES> key. 8. Press the <ESC> key to return to the previous menu. 4-1-3 Programming arrangement Operation 0.00 4.

  • Page 37: Programming Batch X/z Report

    4. Select “4. Batch X/Z” and press the <YES> key. 5. Select an appropriate record, enter the report code (refer to 0.00 the next page) and press the <YES> key. 6. Press the <ESC> key to return to the previous menu. TE-7000S/8000F/8500F Programming Manual P-37...

  • Page 38

    Program 3 Worksheet for batch X/Z report program Description Choice Program code Yes = 0 Allow to issue read report. No = 1 Yes = 0 Allow to issue reset report. (a+b+c) No = 2 Read = 0 Read / Reset selection (direct issuance) Reset = 4 Reported area: Significant...

  • Page 39: Programming The General Feature

    You can choose VAT / Single tax, US, Canada, Singapore tax system. 6. VLD compulsory and drawer open: You can choose “At once” and “After compulsory.” 7. Money-in-drawer limit alarm: (sentinel amount) You can enter “Maximum value of left-most digit” and “ The number of zeros.” TE-7000S/8000F/8500F Programming Manual P-39...

  • Page 40

    Program 3 4-1-5-2 Programming the machine control 2 Operation 0.00 5. Select “2. Machine Control2” and press the <YES> key. 0.00 0.00 0.00 0.00 6. Select the field you want to change and press the <YES>/ <NO> key or enter the numeric value and press the <YES> key.

  • Page 41

    If you select “YES”, you must press the <YES> key when you select an item in pulldown group. If you select “No”, it is not necessary to press the <YES> key, you can designate an item in a pulldown group by entering 1 thru 9. TE-7000S/8000F/8500F Programming Manual P-41...

  • Page 42

    Program 3 4-1-5-3 Programming the machine control 3 Operation 0.00 5. Select “3. Machine Control3” and press the <YES> key. 0.00 0.00 0.00 6. Select the field you want to change and press the <YES>/ <NO> key. 7. After programming, you should press the <ESC> key to return to the previous menu.

  • Page 43

    1. Compulsory drawer control for multiple drawers: You can choose “All drawers” / “Drawer assigned to the clerk”. 2. Scan link start record No.: The PLU items that are set after this record number are treated as scanning PLU items. TE-7000S/8000F/8500F Programming Manual P-43...

  • Page 44

    Program 3 4-1-5-5 Programming the print control Operation 0.00 5. Select “5. Print Control” and press the <YES> key. 0.00 0.00 0.00 6. Select the field you want to change and press the <YES> / <NO> key. 7. After programming, you should press the <ESC> key to return to the previous menu.

  • Page 45

    6. Select the field you want to change and press the <YES> / <NO> key. 7. After programming, you should press the <ESC> key to return to the previous menu. Field meaning These items are included in the fixed totalizer report. TE-7000S/8000F/8500F Programming Manual P-45...

  • Page 46

    Program 3 4-1-5-7 Programming the report control 2 Operation 0.00 5. Select “7. Report Control2” and press the <YES> key. 0.00 0.00 0.00 0.00 0.00 6. Select the field you want to change and press the <YES> / <NO> key. 7.

  • Page 47

    Broadcast the programmed data in PGM 1 ~ 4 mode after completion of a program. 2. Origin of reset data to be sent to the master: You can choose “Own data file” or “Consolidation file.” 3. Stock result copy: Copy stock quantity to master daily file after Z consolidation. TE-7000S/8000F/8500F Programming Manual P-47...

  • Page 48

    Program 3 4-1-5-9 Programming the hourly sales Operation 0.00 5. Select “9. Hourly Sales” and press the <YES> key. 6. Select the field you want to change and press the <YES> / <NO> key. 0.00 7. After programming, you should press the <ESC> key to return to the previous menu.

  • Page 49

    2. Generate E-Journal full error: Alert when the electronic journal memory becomes full/Not alert even if the electronic journal memory becomes full. 3. Journal Compression Print: Print journal by normal height character (“NO”), or by half height character (“YES”). TE-7000S/8000F/8500F Programming Manual P-49...

  • Page 50

    Program 3 4-1-5-12 Programming the message control Operation 0.00 5. Select “12. Message Control” and press the <YES> key. 0.00 0.00 6. Select the field you want to change and press the <YES> / <NO> key. 7. After programming, you should press the <ESC> key to return to the previous menu.

  • Page 51

    Allow to enter the number of the condiment, and not follow the quantities of main PLU. Fine Dining QTY: Not allow to enter the number of the condiment but allow to select the condiment by LIST staydown within the quantities of main PLU. TE-7000S/8000F/8500F Programming Manual P-51...

  • Page 52

    Program 3 4-1-5-15 Programming the check tracking Operation 0.00 5. Select “15. CHK Tracking” and press the <YES> key. 0.00 0.00 6. Select the field you want to change and press the <YES> / <NO> key or enter the numeric value and press the <YES> key.

  • Page 53

    6. Select the field you want to change and press the <YES> key. 0.00 7. After programming, you should press the <ESC> key to return to the previous menu. Field meaning 1. Backlight Off Timer: 0 - 59. (Minute) TE-7000S/8000F/8500F Programming Manual P-53...

  • Page 54

    Program 3 4-1-5-18 Programming the menu shift 1 Operation 0.00 5. Select “18. Menu Shift 1” and press the <YES> key. 0.00 6. Select the field you want to change and press the <YES> / <NO> key. 7. After programming, you should press the <ESC> key to return to the previous menu.

  • Page 55

    6. Select the field you want to change and enter the numeric 0.00 value and press the <YES> key. 7. After programming, you should press the <ESC> key to return to the previous menu. Field meaning Define start PLU No. of each menu shift. TE-7000S/8000F/8500F Programming Manual P-55...

  • Page 56: Programming Scheduler

    Program 3 4-1-6 Programming scheduler Operation 0.00 4. Select “6. Scheduler” and press the <YES> key. 0.00 5. Enter schedule (refer to the next page) and press the <YES> key. 6. Press the <ESC> key to return to the previous menu. P-56...

  • Page 57

    : : : : Significant Interval time (00:00 ~ 23:59) numbers Always “0” : : : : Significant Arrangement table No. numbers : : : Significant Arrangement file No. numbers ; ; ; ; Always “0000” TE-7000S/8000F/8500F Programming Manual P-57...

  • Page 58: Programming Check Print

    Program 3 4-1-7 Programming check print Operation 0.00 4. Select “7. Check Print” and press the <YES> key. 0.00 5. Enter value (below) and press the <YES> key. 6. Press the <ESC> key to return to the previous menu. Worksheet for check print program Description Choice Program code...

  • Page 59: Programming Table Analysis

    Minimum check No. of the group Significant (“0” means “1.”) numbers :::::: Maximum check No. of the group Significant (“000000” means no programming.) numbers Note: This programming is only effective, if the check-# is 6-digit long. TE-7000S/8000F/8500F Programming Manual P-59...

  • Page 60: Programming Tax Table

    Program 3 4-1-9 Programming tax table Operation 0.00 4. Select “9. Tax Table” and press the <YES> key. 0.00 5. Select an appropriate table and press the <YES> key. 6. Select an appropriate row and press the <YES> key. 0.00 7.

  • Page 61

    • Non-cyclic values and one set of cyclic values (actual values): 7, 14, 14, 14, 15, 14, 14, 15 • Maximum taxable amount in table calculation: $20.07 • Tax system: Tax table with rate • Tax rate: 7.000% • Rounding method: Cut off to two decimal places TE-7000S/8000F/8500F Programming Manual P-61...

  • Page 62

    Program 3 Explanation of VAT & VAT Example 1: Share the amount Tax table programming Tax rate Calculation Primary Secondary (Share rate) type tax status tax status Table 1 10.0000% Table 2 20.0000% 33.3333% for taxable 1 Table 4 33.3333% VAT &...

  • Page 63: Programming Void Table

    8. Enter value (below) and press the <YES> key. 9. Press the <ESC> key to return to the previous menu. Worksheet for void table program Description Choice Program code Yes = 0 Return stock value. No = 1 TE-7000S/8000F/8500F Programming Manual P-63...

  • Page 64: Programming System Connection

    Program 3 4-1-11 Programming system connection Operation 0.00 4. Select “11. System Connection” and press the <YES> key. 5. Select the record with “*” and press the <YES> key. 6. Enter the logical ID character within 12 characters and press the <YES>...

  • Page 65: Programming I/o Parameter

    38400bps = 3, 19200bps = 4, 9600bps = 5, number 4800bps = 6, 2400bps = 7 Activation signal (trigger): Significant DR = 0, CI = 1 number Third record (not used) Description Choice Program code Always “0” TE-7000S/8000F/8500F Programming Manual P-65...

  • Page 66

    Program 3 Note: Besides flag clear, please turn off and on Fourth record (Printer 1) the printer. Description Choice Program code Using RS-232C port for printer: Significant COM2 = 2, COM3 = 3, COM4 = 4 (0, 1, 5 ~ 9: no connection) number Baud rate of the RS-232C port for printer: Significant...

  • Page 67

    Program code Always “0” Thirteenth record (Menu sheet) Description Choice Program code Significant Internal default number of menu shift number (menu shift 1 = 0, 1, menu shift 2 = 2 .., menu shift 8 = 8) TE-7000S/8000F/8500F Programming Manual P-67...

  • Page 68: Programming Printer Connection

    Program 3 4-1-13 Programming printer connection Operation 0.00 4. Select “13. Printer Connection” and press the <YES> key. 5. Select an appropriate record and press the <YES> key. 0.00 6. Select the printer type, “1. No, 2. Rct, 3. Report, 4 ~ 10.

  • Page 69: Programming Time Zone

    00 ~ 59 Zone End Time (Hour) (00~23) 00 ~ 23 Zone End Time (Minute) (00~59) 00 ~ 59 Zone Cycle (Hour) (00~23) 00 ~ 23 Zone Cycle (Minute) (00, 15, 30, 45) 00, 15, 30, 45 TE-7000S/8000F/8500F Programming Manual P-69...

  • Page 70: Programming Time & Attendance

    Program 3 4-1-15 Programming time & attendance Preparation 0.00 4. Select “15. Time & Attendance” and press the <YES> key. 4-1-15-1 Programming time & attendance (general) Operation 0.00 5. Select “1. General” and press the <YES> key. 0.00 6. Select an appropriate record and choose options. 7.

  • Page 71

    5. Select “2. Job Code” and press the <YES> key. 0.00 6. Select an appropriate job code and press the <YES> key. 0.00 7. Select an appropriate record to enter the character or number and press the <YES> key, or choose option. TE-7000S/8000F/8500F Programming Manual P-71...

  • Page 72

    Program 3 4-1-15-3 Programming time & attendance (employee & schedule) Operation 0.00 5. Select “3. Employee&Schedule” and press the <YES> key. 0.00 6. Select an appropriate employee file, and press the <YES> key. 0.00 0.00 7. Select an appropriate record to enter the character or choose options.

  • Page 73

    0.00 9. Select an appropriate day, and press the <YES> key. 0.00 10. Select an appropriate record to enter the appropriate job and time. TE-7000S/8000F/8500F Programming Manual P-73...

  • Page 74: Programming Hourly Item Link

    Program 3 4-1-16 Programming hourly item link Operation 0.00 4. Select “16. Hourly/Item Link” and press the <YES> key. 0.00 5. Select an appropriate record, and press the <YES> key. 6. Select an appropriate record, and choose the items from PLU, subdepartment, department, function, fixed totalizer, group, and void reason.

  • Page 75: Programming Idc Link

    To clear the record, enter “0” and then press the <YES> key. 2. Store File: Specify the option for the Store File; “NO / IDC(1) / IDC(2) / IDC(3)”. 3. Store Data: Specify the option for the store file; “Item only / Whole Transaction”. TE-7000S/8000F/8500F Programming Manual P-75...

  • Page 76: Programming Euro

    Program 3 4-1-18 Programming Euro Operation 0.00 4. Select “18. EURO (sub currency ” and press the <YES> key. 0.00 0.00 5. Select the field you want to change and press the <YES> / <NO> key or enter the numeric value and press the <YES> key.

  • Page 77: Programming Auto Program Control

    : : : : Significant File No. numbers No = 0 Broadcast this file (designated by D ) only. Yes = 1 No = 0 Ignore to receive this file (designated by D Yes = 1 TE-7000S/8000F/8500F Programming Manual P-77...

  • Page 78: Programming Lcd Color Control

    Program 3 4-1-20 Programming LCD color control This program controls color LCD. Operation 0.00 4. Select “20. LCD Color” and press the <YES> key. 0.00 5. Select an appropriate record, and enter the program code. 6. Press the <ESC> key to return to the previous menu. Worksheet for LCD color control 0001-906 (Color pattern selection) Description...

  • Page 79

    9th record Guidance area 0 000 000 000 253 198 0 000 000 000 256 230 0 000 000 000 253 198 Note: These images are printing samples. The displaying color images are different from above samples. TE-7000S/8000F/8500F Programming Manual P-79...

  • Page 80

    Program 3 Field area / window meaning Color code table Main window (Header, Scroll, Entry, Status/ST area) (256) (255) (254) (253) (252) (251) (250) (249) (248) (247) (246) (245) (244) (243) (242) (241) Header area character back ground (240) (239) (238) (237) (236) (235) (234) (233) (232) (231) (230) (229) (228) (227) (226) (225) (224) (223) (222) (221) (220) (219) (218) (217) (216) (215) (214) (213) (212) (211) (210) (209) Scroll area...

  • Page 81: Programming Australian Gst Control

    4. Select “21. Aust Features” and press the <YES> key. 5. Select the field you want to change and press the <YES> / 0.00 <NO> key. 6. Press the <ESC> key to return to the previous menu. TE-7000S/8000F/8500F Programming Manual P-81...

  • Page 82: Programming Clerks, Programming Clerk Features

    Program 3 4-2. Programming clerks Preparation: 1. Sign on a clerk (if necessary). 2. Press <PGM MODE> repeatedly or “3” <PGM MODE> to assign Program 3 mode. 0.00 3. Select “2. Clerk” and press the <YES> key. 4-2-1 Programming clerk features Operation 0.00 4.

  • Page 83

    1. Type of operator: Choose “Cashier/Clerk/Manager.” 2. Void operation: Choose “Current only/Complete void/Not allowed.” 3. Descriptor (16 digits) 4. Secret code (1 ~ 9999) 5. Check number for clerk interrupt (1 ~ 999999) 6. Drawer number (1 ~ 4) TE-7000S/8000F/8500F Programming Manual P-83...

  • Page 84: Programming Operation

    Program 3 4-2-2 Programming operation Preparation 0.00 4. Select “2. Operation” and press the <YES> key. 4-2-2-1 Programming clerk control Operation 0.00 5. Select “1. Clerk Control” and press the <YES> key. 0.00 6. Select an appropriate clerk and press the <YES> key. 0.00 7.

  • Page 85

    Price shift after sign on: (1 ~ 2) Default No. of each subject after signing on. 3. Menu shift status/stay down: Price shift status/stay down: Not maintain/Maintain menu sheet No./@ menu sheet No. after item registration. TE-7000S/8000F/8500F Programming Manual P-85...

  • Page 86

    Program 3 4-2-2-3 Programming mode control Operation 0.00 5. Select “3. Mode Control” and press the <YES> key. 0.00 6. Select an appropriate clerk and press the <YES> key. 0.00 0.00 7. Select an appropriate record and choose options. 8. After programming, press the <ESC> key to return to the previous menu.

  • Page 87

    6. Select an appropriate clerk and press the <YES> key. 0.00 0.00 0.00 7. Select an appropriate record and press the <YES> / <NO> key. 8. After programming, press the <ESC> key to return to the previous menu. TE-7000S/8000F/8500F Programming Manual P-87...

  • Page 88

    Program 3 4-2-2-5 Programming function control 2 Operation 0.00 5. Select “5. Allowed function 2” and press the <YES> key. 0.00 6. Select an appropriate clerk and press the <YES> key. (not used) 0.00 0.00 0.00 7. Select an appropriate record and press the <YES> / <NO> key.

  • Page 89

    6. Select an appropriate clerk and press the <YES> key. 0.00 0.00 7. Select an appropriate record and press the <YES> / <NO> key. 8. After programming, press the <ESC> key to return to the previous menu. TE-7000S/8000F/8500F Programming Manual P-89...

  • Page 90

    Program 3 4-2-2-7 Programming function control 4 Operation 0.00 5. Select “7. Allowed function 4” and press the <YES> key. 0.00 6. Select an appropriate clerk and press the <YES> key. 0.00 0.00 7. Select an appropriate record and press the <YES> / <NO> key.

  • Page 91

    6. Select an appropriate clerk and press the <YES> key. 0.00 7. Select an appropriate record and press the <YES> / <NO> key. 8. After programming, press the <ESC> key to return to the previous menu. TE-7000S/8000F/8500F Programming Manual P-91...

  • Page 92

    Program 3 4-2-2-9 Programming arrangement control Operation 0.00 5. Select “9. Arrangement” and press the <YES> key. 0.00 6. Select an appropriate clerk and press the <YES> key. 0.00 7. Select an appropriate record and press the <YES> / <NO> key.

  • Page 93

    6. Select an appropriate clerk and press the <YES> key. 0.00 0.00 0.00 7. Select an appropriate record and press the <YES> / <NO> key. 8. After programming, press the <ESC> key to return to the previous menu. TE-7000S/8000F/8500F Programming Manual P-93...

  • Page 94: Programming Commission Rate

    Program 3 4-2-3 Programming commission rate Operation 0.00 4. Select “3. Commission Rate” and press the <YES> key. 0.00 5. Select an appropriate clerk and press the <YES> key. 0.00 7. Select an appropriate record and enter value (0 ~ 99.99), and then press the <YES>...

  • Page 95: Programming Table Range

    5. Select an appropriate clerk and press the <YES> key. 0.00 7. Select an appropriate record and enter values (0 ~ 999999), and then press the <YES> key. 8. After programming, press the <ESC> key to return to the previous menu. TE-7000S/8000F/8500F Programming Manual P-95...

  • Page 96: Programming Clerk Control By Range

    Program 3 4-2-5 Programming clerk control by range Preparation 0.00 4. Select “5. Range” and press the <YES> key. 4-2-5-1 Programming clerk control by range Operation 0.00 5. Select “1. Clerk Control” and press the <YES> key. 6. Select an appropriate record and choose options. 0.00 7.

  • Page 97

    Then enter the end range No. and press the <YES> key. (It ends the last record if you skip to enter the end range.) 9. Press the <YES> key. 10. Press the <ESC> key to return to the previous menu. TE-7000S/8000F/8500F Programming Manual P-97...

  • Page 98

    Program 3 4-2-5-3 Programming mode control by range Operation 0.00 5. Select “3. Mode Control” and press the <YES> key. 0.00 0.00 6. Select an appropriate record and choose options. 7. After programming, press the <ESC> key to proceed to the next step.

  • Page 99

    Then enter the end range No. and press the <YES> key. (It ends the last record if you skip to enter the end range.) 9. Press the <YES> key. 10. Press the <ESC> key to return to the previous menu. TE-7000S/8000F/8500F Programming Manual P-99...

  • Page 100

    Program 3 4-2-5-5 Programming function control 2 by range Operation 0.00 5. Select “5. Allowed function 2” and press the <YES> key. 0.00 0.00 0.00 6. Select an appropriate record and press the <YES> / <NO> key. 7. After programming, press the <ESC> key to proceed to the next step.

  • Page 101

    Then enter the end range No. and press the <YES> key. (It ends the last record if you skip to enter the end range.) 9. Press the <YES> key. 10. Press the <ESC> key to return to the previous menu. TE-7000S/8000F/8500F Programming Manual P-101...

  • Page 102

    Program 3 4-2-5-7 Programming function control 4 by range Operation 0.00 5. Select “7. Allowed function 4” and press the <YES> key. 0.00 0.00 6. Select an appropriate record and press the <YES> / <NO> key. 7. After programming, press the <ESC> key to proceed to the next step.

  • Page 103

    Then enter the end range No. and press the <YES> key. (It ends the last record if you skip to enter the end range.) 9. Press the <YES> key. 10. Press the <ESC> key to return to the previous menu. TE-7000S/8000F/8500F Programming Manual P-103...

  • Page 104

    Program 3 4-2-5-9 Programming arrangement control by range Operation 0.00 5. Select “9. Arrangement” and press the <YES> key. 0.00 6. Select an appropriate record and press the <YES> / <NO> key. 7. After programming, press the <ESC> key to proceed to the next step.

  • Page 105

    Then enter the end range No. and press the <YES> key. (It ends the last record if you skip to enter the end range.) 9. Press the <YES> key. 10. Press the <ESC> key to return to the previous menu. TE-7000S/8000F/8500F Programming Manual P-105...

  • Page 106

    Program 3 4-2-5-11 Programming commission rate by range Operation 0.00 5. Select “11. Commission Rate” and press the <YES> key. 0.00 6. Select an appropriate record, enter the rate and press the <YES> key. 7. After programming, press the <ESC> key to proceed to the next step.

  • Page 107

    Then enter the end range No. and press the <YES> key. (It ends the last record if you skip to enter the end range.) 9. Press the <YES> key. 10. Press the <ESC> key to return to the previous menu. TE-7000S/8000F/8500F Programming Manual P-107...

  • Page 108: Programming Clerk Detail

    Program 3 4-2-6 Programming clerk detail Operation 0.00 4. Select “6. Clerk Detail” and press the <YES> key. Addition/Modification 0.00 7. Select a record you want to add an item or modify the item and press the <YES> key. 0.00 8.

  • Page 109: Programming Clerk Key Id

    5. Touch the Dallas key with the receiver, and press the <YES> key. 6. Select the appropriate clerk. 7. Repeat step 5 to 6, until completing this procedure. 8. Press <ESC> key to terminate the program and return to the previous menu. TE-7000S/8000F/8500F Programming Manual P-109...

  • Page 110: Programming Key Features, Programming Plu Features

    Program 3 4-3. Programming key features Preparation: 1. Sign on a clerk (if necessary). 2. Press <PGM MODE> repeatedly or “3” <PGM MODE> to assign Program 3 mode. 0.00 3. Select “3. Key Feature” and press the <YES> key. 4-3-1 Programming PLU features Operation 0.00...

  • Page 111

    “0” and press the <YES> key. • If you designate PLU by random code instead of memory number, set “Use random code” in the machine control 2 of general features in PGM 3. (refer to page 40.) TE-7000S/8000F/8500F Programming Manual P-111...

  • Page 112: Programming Plu 2nd@ Features

    Program 3 4-3-2 Programming PLU 2nd@ features Operation 0.00 4. Select “2. PLU 2nd@” and press the <YES> key. 5. Select an appropriate item directly, by entering record No. or by entering PLU No. and press the <YES> key. In this step, 0.00 you can use “Character search”...

  • Page 113: Programming Subdepartment Features

    1. Descriptor: 0 - 16 character, Price: 0 - 999999, Number of Bon: 1 - 9, High amount limit: 0 - 999999, Low digit limit: 0, 1 - 7, (8, 9; prohibit entry) 2. Refer to 4-3-1. PLU features for other field meanings. TE-7000S/8000F/8500F Programming Manual P-113...

  • Page 114: Programming Department Features

    Program 3 4-3-4 Programming department features Operation 0.00 4. Select “4. Department” and press the <YES> key. 0.00 5. Select an appropriate item directly or by entering record No. and press the <YES> key. 0.00 0.00 0.00 6. Select an appropriate record and press the <YES> / <NO> key or enter the numeric value and press the <YES>...

  • Page 115: Programming By Range

    Programming by range Operation 0.00 4. Select “5. Range” and press the <YES> key. Select the subject you want to program 0.00 0.00 0.00 0.00 5. Select “1. PLU/2. PLU 2nd@/3. Sub-Department/4. Department” and press the <YES> key. TE-7000S/8000F/8500F Programming Manual P-115...

  • Page 116

    Program 3 4-3-5-1 General procedure of PLU, PLU 2nd@, subdepartment, department by range 0.00 6. Select an appropriate job (refer to the next page) and press the <YES> key. 0.00 7. Select an appropriate type and press the <YES> key. 8.

  • Page 117

    24. High Amount Limit 32. Low Digit Limit 26. Low Digit Limit 25. Low Digit Limit 33. Multiple VLD 27. Multiple VLD 26. Multiple VLD 34. Use main Item Amt Only 35. Use Premium Item of Set TE-7000S/8000F/8500F Programming Manual P-117...

  • Page 118: Programming Individual Program

    Program 3 4-3-6 Programming individual program Operation 0.00 4. Select “6. Individual PGM” and press the <YES> key. Select the job you want to program 5. Select jobs listed below. 1. Receipt Type 19. Unit Stock: 0.001 - 99.9999 2. Item Type 20.

  • Page 119: Programming Key Function Program

    5. Enter program code (refer to the worksheet on the following pages) and press the function key. Key descriptor 6. Press the <ESC> key to return to the previous menu. NOTE: Press an appropriate function key without number entry on the keyboard, it shows current setting. TE-7000S/8000F/8500F Programming Manual P-119...

  • Page 120

    Program 3 4-3-7-1 Worksheet for cash, charge, credit and check Description Choice Program code No = 0 Restriction (to 0, 5) on last digit for amount tendered. Yes = 1 Significant Allowable number of validation printing (“0” means no limitation) *1 *2 *3 *4 number (0 ~9) No = 0...

  • Page 121

    Yes = 1 (a+b) Amount = 0 Service charge 1 Use an amount 2 Use a rate Rate = 2 Yes = 0 Issue receipt while check tracking/clerk interrupt. No = 2 ; ; ; ; Always “0000” TE-7000S/8000F/8500F Programming Manual P-121...

  • Page 122

    Program 3 4-3-7-3 Worksheet for text print, text recall Description Choice Program code Start record number of displaying “TEXT RECALL WINDOW” Significant (“00” means “01”.) numbers Allow clerk change or mode change after pressing <TEXT RE- Yes = 0 No = 1 CALL>...

  • Page 123

    If “No”, only one validation printing is possible.) ; ; ; ; Always “0000” ; ; ; Always “000” Significant High digit limitation (HDL) for manually entered unit price number (“9” means NOT allow manual entry) Always “00” TE-7000S/8000F/8500F Programming Manual P-123...

  • Page 124

    Program 3 4-3-7-8 Worksheet for loan, pick up Description Choice Program code Significant Allowable number of validation printing (“0” means no limitation) number (0 ~9) No = 0 Force validation operation. (only effective after receipt issuance) Yes = 1 ; ; ; ; ; Always “00000”...

  • Page 125

    Significant High digit limitation (HDL) for manually entered unit price number (“9” means NOT allow manual entry.) No = 0 Commission 1 Yes = 1 (a+b) No = 0 Commission 2 Yes = 2 Always “0” TE-7000S/8000F/8500F Programming Manual P-125...

  • Page 126

    Program 3 4-3-7-11 Worksheet for deposit+, deposit– Description Choice Program code No = 0 Force validation operation. Yes = 1 (a+b) Yes = 0 Multiple validation (If “No”, only one validation is possible.) No = 4 Always “00” DEPO+ = 0 Key attribution DEPO–...

  • Page 127

    No = 1 (a+b) Yes = 0 Allow key operation after item registration. No = 4 Always “0” No = 0 Commission 1 Yes = 1 (a+b) No = 0 Commission 2 Yes = 2 Always “0” TE-7000S/8000F/8500F Programming Manual P-127...

  • Page 128

    Program 3 4-3-7-15 Worksheet for receipt Description Choice Program code Significant Maximum number of post receipts (0 ~ 9) number (“0” means 1 post receipt.) ; ; ; ; Always “0000” 1 = 0 Electronic journal is printed by the printer: 2 = 1 1 Defined in printer connection table, 2 Internal 1 = 0...

  • Page 129

    Enable operation in Manager mode. No = 2 (a+b+c) Yes = 0 Enable operation in Collection / Consolidation mode. No = 4 : : : Significant Arrangement file number numbers : : : : Significant Arrangement table number numbers TE-7000S/8000F/8500F Programming Manual P-129...

  • Page 130

    Program 3 4-3-7-19 Worksheet for currency exchange Description Choice Program code Significant Define amount symbol. (1 ~ 4) number Significant Define foreign currency totalizer. (1 ~ 3) number Significant Rounding: number Round off = 0, cut off = 1, round up = 2 Always “0”...

  • Page 131

    No = 1 (a+b) Yes = 0 Release seat number compulsory. No = 4 Yes = 0 Release tip declaration compulsory. No = 1 (a+b) Yes = 0 Release eat-in / takeout compulsory. No = 2 Always “0” TE-7000S/8000F/8500F Programming Manual P-131...

  • Page 132

    Program 3 4-3-7-24 Worksheet for clerk number Description Choice Program code : : : : Clerk secret number (0000 ~ 9999) Significant numbers (“0000” means no secret number.) 4-3-7-25 Worksheet for operator X/Z Description Choice Program code 1 = 0 1 Issue stand-alone report./2 Issue consolidation report.

  • Page 133

    Significant Record No. of linking pulldown menu group (3). numbers : : : Significant Record No. of linking pulldown menu group (2). numbers : : : Significant Record No. of linking pulldown menu group (1). numbers TE-7000S/8000F/8500F Programming Manual P-133...

  • Page 134

    Program 3 4-3-7-32 Worksheet for tax exempt Description Choice Program code Yes = 0 U.S., Singapore: No = 1 Exempt tax 1 Yes = 0 Exempt tax 2 No = 2 (a+b+c) Yes = 0 Exempt tax 3 No = 4 Significant Canada: number...

  • Page 135

    4-3-7-39 Worksheet for round repeat Description Choice Program code Yes = 0 Perform new balance after round repeat. No = 1 (a+b) Include plus/minus, premium/discount result to round Yes = 0 repeat amount. No = 2 TE-7000S/8000F/8500F Programming Manual P-135...

  • Page 136

    Program 3 4-3-7-40 Worksheet for shift PLU Description Choice Program code 2 = 0 Shift: 1 = 1 1 Status, 2 Staydown Significant Define assigning shift PLU number. (0, 1 ~ 8) (“0” means “1”.) number 4-3-7-41 Worksheet for old check Description Choice Program code...

  • Page 137: Programming Shift Plu Program

    “Character search” to select the item. (Refer to page 33 of this manual.) 0.00 6. Select an appropriate price and enter the unit price. 7. Press the <ESC> key to return to the previous menu. TE-7000S/8000F/8500F Programming Manual P-137...

  • Page 138: Programming Scanning Plu Link Program

    Program 3 4-3-9 Programming scanning PLU link program Operation 0.00 4. Select “9. Scanning PLU Link” and press the <YES> key. 0.00 5. If you append a new PLU or modify an existing PLU, select “Append/Mod PLU”. If you delete an existing PLU, select “Delete PLU”.

  • Page 139

    Delete PLU 0.00 6. Scanning the barcode or enter the PLU code and press the <OBR> key. After this step, go to the step 5 automatically. TE-7000S/8000F/8500F Programming Manual P-139...

  • Page 140: Programming Plu By Pulldown Group

    Program 3 4-3-10 Programming PLU by Pulldown group Operation 0.00 4. Select “10. Pulldown group” and press the <YES> key. 0.00 5. Select the LIST directly, or by entering record No. and press the <YES> key. 6. Select the PLU and press the <YES> key. 0.00 In case of selecting the child LIST, press the <YES>...

  • Page 141

    7. Select an appropriate record and press the <YES>/<NO> key or enter the numeric value and press the <YES> key. 8. Press the <ESC> key to return to the previous menu. Field meaning Please refer to the “4-3-1. Programming PLU Features”. TE-7000S/8000F/8500F Programming Manual P-141...

  • Page 142

    Program 3 P-142...

  • Page 143

    Programming fixed totalizer descriptors ............P-156 5-3-5 Programming group character ..............P-157 5-3-6 Programming special characters ..............P-157 5-3-7 Programming report headers ..............P-159 5-3-8 Programming endorsement message ............P-160 5-3-9 Programming GT character ................ P-160 TE-7000S/8000F/8500F Programming Manual P-143...

  • Page 144: Program 2, Character Programming, Character Programming Keyboard

    (menu sheet) for direct input, or using character codes to specify the characters. 5-1-1 Character programming keyboard When you enter the Program 2 mode, the keyboard becomes a character programming keyboard (shown below). TE-7000S character keyboard ESC/ RECEIPT JOURNAL SKIP...

  • Page 145

    The < > and < > key moves the insertion/deletion point. π ∫ ª º <SHIFT> ∫ π º ª <CAP> ∫ º π ª <DBL> <INS> <DEL> PLU0001 0.00 ∞ ©º Icon (It shows a sort of the character input) TE-7000S/8000F/8500F Programming Manual P-145...

  • Page 146: Inputting Characters By Code, After Completing To Input Characters

    Program 2 5-1-2 Inputting characters by code You can also program text by inputting codes that correspond to the characters you want to input. A list of character codes is given in the table below. You must also use the <B> key on the 10-key pad during character code programming to fix character codes for the last input character.

  • Page 147: Programming Item Descriptors, Programming Plu Item Descriptors

    6. After pressing the <YES> key again, the original descriptors are shown in the lower column of the display. Then enter PLU0001 characters (max. 24 characters) and press the <YES> key to fix them. 7. Press the <ESC> key to return to the previous menu. TE-7000S/8000F/8500F Programming Manual P-147...

  • Page 148: Programming Plu 2nd Unit Price Descriptors, Programming Subdepartment Descriptors

    Program 2 5-2-2 Programming PLU 2nd unit price descriptors Operation 0.00 4. Select “2. PLU 2nd@” and press the <YES> key. 5. Select the PLU directly, or by entering record No. and press the <YES> key or by entering random code and press the 0.00 <PLU No.>...

  • Page 149: Programming Department Descriptors

    7. Press the <ESC> key to return to the previous menu. 5-2-4 Programming department descriptors Operation 0.00 4. Select “4. Department” and press the <YES> key. 0.00 5. Select the <DEPARTMENT> directly, by entering depart- ment No. and press the <YES> key. TE-7000S/8000F/8500F Programming Manual P-149...

  • Page 150: Programming Plu/subdepartment/department Descriptors By Range

    Program 2 6. After pressing the <YES> key again, the original descriptors DEPT01 are shown in the lower column of the display. Then enter characters and press the <YES> key to fix them. 7. Press the <ESC> key to return to the previous menu. 5-2-5 Programming PLU/subdepartment/department descriptors by range Operation...

  • Page 151: Copying Plu Descriptors To Plu 2nd Unit Price

    (It starts “0001” if you skip to enter the start range.) 0.00 Then enter the end range No. and press the <YES> key. (It ends the last record if you skip to enter the end range.) TE-7000S/8000F/8500F Programming Manual P-151...

  • Page 152: Programming Function Key Descriptors

    Program 2 0.00 6. Press the <YES> key and return to the previous menu. 5-2-7 Programming function key descriptors Operation 0.00 4. Select “7. Char & Press Key” and press the <YES> key. 5. a) Function keys (max. 16 characters) Enter characters, press the <YES>...

  • Page 153: Programming Plu Descriptors By Pulldown Group

    6. Select the PLU directly and enter character and press the 0.00 <YES> key. 7. In case of selecting the child LIST, press the <YES> key will 0.00 show the contents of the child LIST. 8. Press the <ESC> key to return to the previous menu. TE-7000S/8000F/8500F Programming Manual P-153...

  • Page 154: Programming Characters And Messages

    Program 2 5-3. Programming characters and messages Preparation: 1. Sign on a clerk (if necessary). 2. Press <PGM MODE> repeatedly or “2” <PGM MODE> to assign Program 2 mode. 0.00 3. Select “2. Char & Message” and press the <YES> key. 5-3-1 Programming receipt message, slip message and guest receipt message Operation...

  • Page 155: Programming Text Recall Message, Programming Order Character Link

    4. Select “3. Order Char Link” and press the <YES> key. 0.00 5. Select the appropriate record, press the <YES> key, enter characters (Maximum 16 characters) and press the <YES> key. 6. Press the <ESC> key to return to the previous menu. TE-7000S/8000F/8500F Programming Manual P-155...

  • Page 156: Programming Fixed Totalizer Descriptors

    Program 2 5-3-4 Programming fixed totalizer descriptors Operation 0.00 4. Select “4. Fixed Totalizer” and press the <YES> key. 5. Select the appropriate record, press the <YES> key, enter characters (Maximum 16 characters) and press the <YES> key. 0.00 6. Press the <ESC> key to return to the previous menu. Rec No.

  • Page 157: Programming Group Character, Programming Special Characters

    4. Select “6. Special Character” and press the <YES> key. 0.00 5. Select the appropriate record, press the <YES> key, enter characters and press the <YES> key. 6. Press the <ESC> key to return to the previous menu. TE-7000S/8000F/8500F Programming Manual P-157...

  • Page 158

    Program 2 Rec No. Contents Descriptor Amount symbol (3), @(2), No (2), not used (1), Split pricing (1), U.S. not used (1), Training filler (1) Others No. of item sold (2), Customer count (2), Square (6), Double sized customer count(6) Multiplication (6) U.S.

  • Page 159: Programming Report Headers

    Flash (Financial) report Open check report Table analysis report PLU stock report Void causal report Electronic journal report Time & Attendance Hourly labor Hourly item not used IDC (1) reset IDC (2) reset IDC (3) reset not used TE-7000S/8000F/8500F Programming Manual P-159...

  • Page 160: Programming Endorsement Message, Programming Gt Character

    Program 2 5-3-8 Programming endorsement message Operation 0.00 4. Select “8. Endorse Message” and press the <YES> key. 0.00 5. Select the appropriate record, press the <YES> key, enter characters (Maximum 40 characters) and press the <YES> key. 6. Press the <ESC> key to return to the previous menu. 5-3-9 Programming GT character Operation...

  • Page 161

    Copying PLU unit price to PLU 2nd unit price ..........P-169 6-2-8 Programming amount or rate to keys ............. P-170 6-2-9 Programming unit price of shift PLU............... P-171 6-2-10 Programming unit price of Pulldown group ............ P-172 TE-7000S/8000F/8500F Programming Manual P-161...

  • Page 162: Program 1, Presetting Date And Time

    Program 1 6. Program 1 6-1. Presetting date and time Preparation: 1. Sign on a clerk (if necessary). 2. Press <PGM MODE> repeatedly or “1” <PGM MODE> to assign Program 1 mode. 0.00 Presetting time: 10-10-01 12:34 00 3. Enter the current time in four (hour, minute) digits or in five (hour, minute, ten second) and press the <X>...

  • Page 163: Programming Unit Price And Rate, Programming Plu Unit Price

    6. Enter unit price and press the <YES> key to fix them. 0.00 Pressing <YES> twice programs the same unit price to the next record. 7. Press the <ESC> key to return to the previous menu. TE-7000S/8000F/8500F Programming Manual P-163...

  • Page 164: Programming Plu 2nd Unit Price

    Program 1 6-2-2 Programming PLU 2nd unit price Operation 0.00 4. Select “2. PLU 2nd@” and press the <YES> key. 5. Select the PLU directly, or by entering record No. and press the <YES> key or by entering random code and press the 0.00 <PLU>...

  • Page 165: Programming Plu Unit Price And Plu 2nd Unit Price

    6. Select “Qty” or “Price” field by the cursor keys and enter the unit q’ty/unit price and press the <YES> key to fix them. Pressing <YES> twice programs the same unit q’ty/unit price to the next record. 7. Press the <ESC> key to return to the previous menu. TE-7000S/8000F/8500F Programming Manual P-165...

  • Page 166: Programming Subdepartment Unit Price, Programming Department Unit Price

    Program 1 6-2-4 Programming subdepartment unit price Operation 0.00 4. Select “4. Sub-Department” and press the <YES> key. 0.00 5. Select the subdepartment directly or by entering record No. and press the <YES> key. 6. Enter the unit price and press the <YES> key to fix them. 0.00 Pressing <YES>...

  • Page 167: Programming Plu / Plu 2nd@ / Subdepartment Department Unit Price By Range

    Programming PLU / PLU 2nd@ / subdepartment / department unit price by range Operation 0.00 4. Select “6. Range” and press the <YES> key. 0.00 5. Select the subject you want to modify, “PLU / PLU 2nd@ / Sub-Department / Department” and press the <YES> key. TE-7000S/8000F/8500F Programming Manual P-167...

  • Page 168

    Program 1 0.00 0.00 6. Enter the unit price (and Qty for PLU 2nd@) and press the <YES> key. 7. Enter the start range No. and press the <YES> key. (It starts “0001” if you skip to enter the start range.) 0.00 Then enter the end range No.

  • Page 169: Copying Plu Unit Price To Plu 2nd Unit Price

    Then enter the end range No. and press the <YES> key. (It ends the last record if you skip to enter the end range.) 0.00 6. Press the <YES> key to return to the previous menu. TE-7000S/8000F/8500F Programming Manual P-169...

  • Page 170: Programming Amount Or Rate To Keys

    Program 1 6-2-8 Programming amount or rate to keys Operation 0.00 4. Select “8.AMT/Rate to Key” and press the <YES> key. 5. a) Function keys Enter the unit price or rate and press the corresponding key. (CA, CHK, NB, +, –, CPN, %+, %–, CE) b) PLU Enter the PLU No., press the <PLU>...

  • Page 171: Programming Unit Price Of Shift Plu

    7. Enter unit price and press the <YES> key to fix them. 0.00 Pressing <YES> twice programs the same unit price to the next record. 8. Press the <ESC> key to return to the previous menu. TE-7000S/8000F/8500F Programming Manual P-171...

  • Page 172: Programming Unit Price Of Pulldown Group

    Program 1 6-2-10 Programming unit price of Pulldown group Operation 0.00 4. Select “10. Pulldown group” and press the <YES> key. 0.00 5. Select the LIST directly, or by entering record No. and press the <YES> key. 6. Select the PLU directly and enter the unit price and press the 0.00 <YES>...

  • Page 173

    7-2-1 Unit Price / Qty .................... P-175 7-2-2 Item Descriptor.................... P-176 7-2-3 Character and Message................P-176 7-2-4 Machine feature ..................P-178 7-2-5 Clerk......................P-202 7-2-6 Key feature....................P-214 7-2-7 Keyboard..................... P-219 7-2-8 Memory allocation ..................P-219 TE-7000S/8000F/8500F Programming Manual P-173...

  • Page 174: Program 6, Program Read General Procedure

    Program 6 7. Program 6 7-1. Program read general procedure Operation: 1. Sign on a clerk (if necessary). 2. Press <PGM MODE> repeatedly or “6” <PGM MODE> to assign Program 6 mode. 0.00 3. Press the <YES> key. 0.00 4. Select an appropriate job and press the <YES> key. 5.

  • Page 175: Program Read Report Sample, Unit Price / Qty

    Note: No subdepartment file is allocated after initialization. 7-2-1-4. Department — Department descriptor — Record No. / File No. / Unit Price 7-2-1-5. Function key — Function key descriptor / Record No. / File No. — Unit Price, percent rate or conversion rate TE-7000S/8000F/8500F Programming Manual P-175...

  • Page 176: Item Descriptor, Character And Message

    Program 6 7-2-2 Item Descriptor 7-2-2-1. PLU — PLU descriptor — Record No. / File No. 7-2-2-2. PLU 2nd unit price — PLU 2nd descriptor — Record No. / File No. 7-2-2-3. Subdepartment — Subdepartment descriptor / Record No. / File No. 7-2-2-4.

  • Page 177

    — Report header * / Record No. / File No. * Report header: Refer to page 159 in PGM 2 mode. 7-2-3-9. Endorse message — Record No. / File No. — Endorse message 7-2-3-10. GT character — GT character / Record No. / File No. TE-7000S/8000F/8500F Programming Manual P-177...

  • Page 178: Machine Feature

    Program 6 7-2-4 Machine feature 7-2-4-1. Pulldown group — Record No. / File No. — 0000D — Link PLU record No. / File No. / Descriptor Description Choice Program code Maximum number of stay down Status = 0 Significant The number of stay down = 1 ~ 8, number No limit = 9 Minimum number of stay down...

  • Page 179

    Year/Month/Day = 0/1, Day/Month/Year = 2, Month/Day/Year = 3 Significant Monetary mode: 0 = 0, º0 = 1, º00 = 2, º000 = 3 number (0 ~ 3) ; ; ; ; ; Always “00000” ; ; ; ; ; Always “00000” TE-7000S/8000F/8500F Programming Manual P-179...

  • Page 180

    Program 6 Record 0002-022 Description Choice Program code : : : : Significant Machine number number Record 0003-022 Description Choice Program code No = 0 Reset consecutive number after daily fixed totalizer reset report Yes = 1 is issued. Always “0” : : : : : : Consecutive number start value: (Consecutive number starts this value +1.)

  • Page 181

    Print clear key operation. Yes = 1 Yes = 0 Print number of customers on header. No = 2 (a+b+c) No = 0 Print PLU No. on receipt. (REG / REF / REG- mode only) Yes = 4 TE-7000S/8000F/8500F Programming Manual P-181...

  • Page 182

    Program 6 Record 0006-022 Description Choice Program code Yes = 0 Take over the taxable status and commission status of the No = 1 previous item to + / – key. No = 0 Restrict 0 or 5 on the last digit. (a+b+c) Yes = 2 Yes = 0...

  • Page 183

    Print discount/coupon total. No = 1 Yes = 0 Print refund total. (a+b+c) No = 2 Yes = 0 Print clear counter. No = 4 Yes = 0 Print rounding total. No = 2 Always “00” TE-7000S/8000F/8500F Programming Manual P-183...

  • Page 184

    Program 6 Record 0009-022 Description Choice Program code Yes = 0 Print taxable amount 1. No = 1 Yes = 0 Print tax 1. (a+b+c) No = 2 Yes = 0 Print tax exempt 1. No = 4 Yes = 0 Print taxable amount 2.

  • Page 185

    1 while all drawers open, 2 while clerk’s own drawer opens. (a+b) No = 0 Ignore compulsory drawer sensor. Yes = 2 Significant Till timer (00 ~ 59 minutes) numbers Significant Till timer (00 ~ 59 seconds) numbers TE-7000S/8000F/8500F Programming Manual P-185...

  • Page 186

    Program 6 Record 0012-022 Description Choice Program code Yes = 0 Print grand total 1 (periodic 1 & 2 reset report only). No = 1 Yes = 0 Print grand total 2 (periodic 1 & 2 reset report only). No = 2 (a+b+c) Yes = 0 Print grand total 3 (periodic 1 &...

  • Page 187

    No = 0 Display hourly / labor read report. Yes = 4 ;;;;;; Always “000000”. No = 0 Display employee activity read report. Yes = 2 (a+b) No = 0 Display financial report. Yes = 4 TE-7000S/8000F/8500F Programming Manual P-187...

  • Page 188

    Program 6 Record 0015-022 Description Choice Program code Yes = 0 Zero-skip department / subdepartment report. No = 1 (a+b) Yes = 0 Zero-skip clerk report. No = 2 Yes = 0 Zero-skip transaction report. No = 1 Yes = 0 Zero-skip PLU report.

  • Page 189

    Interval time of hourly report (00 ~ 59 minutes): (“0000” means 01:00.) Start time of hourly report (00 ~ 23 hours) : : : : Significant number Start time of hourly report (00 ~ 59 minutes) TE-7000S/8000F/8500F Programming Manual P-189...

  • Page 190

    Program 6 Record 0017-022 Description Choice Program code No = 0 Money declaration compulsory (cash). (not used) Yes = 1 No = 0 Money declaration compulsory (charge). (not used) (a+b+c) Yes = 2 No = 0 Money declaration compulsory (check). (not used) Yes = 4 No = 0 Money declaration compulsory (credit).

  • Page 191

    Merge the same department / subdepartment / PLU registration No = 0 on slip & guest receipt. (Item consolidation) Yes = 4 Significant Slip auto feed lines. numbers * These programs are only effective for SP-1300. TE-7000S/8000F/8500F Programming Manual P-191...

  • Page 192

    Program 6 Record 0019-022 Description Choice Program code No = 0 Journal compressed print (print journal in half height character.) Yes = 1 Always “0” Yes = 0 Record operations in training mode on journal / electronic journal. No = 2 Yes = 0 Alert electronic journal memory near-end / full error.

  • Page 193

    No = 0 Print “TAX INVOICE” on receipts. Yes = 1 No = 0 Print “DUPLICATE” on receipts. (a+b+c) Yes = 2 No = 0 Print rounding amount on receipts. Yes = 4 ; ~ ; Always “00000000000” TE-7000S/8000F/8500F Programming Manual P-193...

  • Page 194

    Program 6 Record 0024-022 Description Choice Program code No = 0 Restriction (to 0, 5) on last digit for check cashing. Yes = 1 ; ~ ; Always “000000000” Restriction (to 0, 5) on last digit for RC, PD, LOAN, PICK UP, No = 0 DEPOSIT.

  • Page 195

    : : : : Significant Start PLU number of 1st menu sheet numbers : : : : Significant Start PLU number of 2nd menu sheet numbers : : : : Significant Start PLU number of 3rd menu sheet numbers TE-7000S/8000F/8500F Programming Manual P-195...

  • Page 196

    Program 6 Record 0033-022 Description Choice Program code : : : : Significant Start PLU number of 4th menu sheet numbers : : : : Significant Start PLU number of 5th menu sheet numbers : : : : Significant Start PLU number of 6th menu sheet numbers Record 0034-022 Description...

  • Page 197

    7-2-4-8.Table analysis — Table analysis descriptor / Record No. / File No. — Parameter * (Minimum check No.) — Parameter * (Maximum check No.) * Parameter: Refer to the worksheet on page 59 in PGM 3 mode. TE-7000S/8000F/8500F Programming Manual P-197...

  • Page 198

    Program 6 7-2-4-9.Tax table — Record No. / File No. — Tax rate — Table maximum value / maximum amount limit — Rounding code — Table attribution 7-2-4-10. Void table — Void reason character / Record No. / File No. —...

  • Page 199

    Significant Job code 3 (00 ~ 99) number (“00” means no select number) Significant Job code 4 (00 ~ 99) number (“00” means no select number) Significant Cashier / clerk record number (00 ~ 99) number TE-7000S/8000F/8500F Programming Manual P-199...

  • Page 200

    Program 6 7-2-4-16. Job Code — Character / Record No. / File No. — Programming (D ) / Pay rate/Overtime pay ratio Wages = Pay rate Working time (exclude overtime) + Overtime pay ratio Pay rate Overtime Description Choice Program code Significant Character (within a 16-digit) (No character means no setting.) character...

  • Page 201

    * Parameter: Refer to the worksheet on page 77 in PGM 3 mode. 7-2-4-20. LCD color — Record No. / File No. / Parameter * * Parameter: Refer to the worksheet on page 78 in PGM 3 mode. TE-7000S/8000F/8500F Programming Manual P-201...

  • Page 202

    Program 6 7-2-5 Clerk 7-2-5-1. Clerk feature — Clerk name / Record No. / File No. — Clerk secret code — Drawer No. — Check No. for clerk interrupt † — Refer to the record 01-067 † — Refer to the record 02-067 —...

  • Page 203

    No = 0 Seat number compulsory Yes = 1 (a+b) No = 0 Eat-in / Takeout compulsory Yes = 2 Always “0” Void operation: Significant Complete void = 0, Current transaction = 1, Not allowed = 2 number TE-7000S/8000F/8500F Programming Manual P-203...

  • Page 204

    (Do not set the disabled sheet No.) Significant (“0” means depending on setting sheet holder; TE-8000F) number (“0” means the first sheet number; TE-7000S and TE-8500F) Default @ menu sheet number after sign on. (0 ~ 2) Significant (Do not set the disabled sheet No.) number (“0”...

  • Page 205

    No = 1 (a+b) Yes = 0 Enable to operate in CF card Auto-PGM mode No = 2 Always “00” Significant Default mode after sign on: REG = 0, PGM1 = 1, X/Z = 2 number TE-7000S/8000F/8500F Programming Manual P-205...

  • Page 206

    Program 6 Record 04-067 Description Choice Program code Yes = 0 Enable to operate cash. No = 1 Yes = 0 Enable to operate charge. No = 2 (a+b+c) Yes = 0 Enable to operate check. No = 4 Yes = 0 Enable to operate credit.

  • Page 207

    Enable to operate open. No = 1 Yes = 0 Enable to operate preset open. No = 2 (a+b+c) Yes = 0 Enable to operate 1st@. No = 4 Yes = 0 Enable to operate 2nd@. No = 1 TE-7000S/8000F/8500F Programming Manual P-207...

  • Page 208

    Program 6 Record 06-067 Description Choice Program code Yes = 0 Enable to operate operator X/Z. No = 1 Yes = 0 Enable to tray total. (a+b+c) No = 2 Yes = 0 Enable to operate subtotal. No = 4 Yes = 0 Enable to operate receipt on / off.

  • Page 209

    No = 4 Always “0” Yes = 0 Enable to operate all void of this transaction. No = 4 Yes = 0 Enable to operate all void from the top of this receipt. No = 1 TE-7000S/8000F/8500F Programming Manual P-209...

  • Page 210

    Program 6 Record 08-067 Description Choice Program code Yes = 0 Enable to operate price. No = 1 Yes = 0 Enable to operate PLU No. (a+b+c) No = 2 Yes = 0 Enable to operate subdepartment No. No = 4 Yes = 0 Enable to operate department No.

  • Page 211

    Enable to operate arrange group 4. No = 1 (a+b+c) Yes = 0 Enable to operate arrange group 5. No = 2 ; ; ; ; ; Always “00000” ; ; ; ; ; Always “00000” TE-7000S/8000F/8500F Programming Manual P-211...

  • Page 212

    Program 6 Record 10-067 Description Choice Program code Yes = 0 Enable to issue daily X report. No = 1 (a+b) Yes = 0 Enable to issue daily Z report. No = 2 Yes = 0 Enable to issue periodic 1 X report. No = 1 (a+b) Yes = 0...

  • Page 213

    — Record No. / File No. — Detailed total record No. / File No. / Character 7-2-5-3. Clerk key ID (Dallas key ID) — Key ID. / Record No. / File No. — Clerk name / Clerk record No. TE-7000S/8000F/8500F Programming Manual P-213...

  • Page 214: Key Feature

    Program 6 7-2-6 Key feature 7-2-6-1. PLU — PLU descriptor † — Record No. / File No. / Elementary program † — Refer to the field 11-066 — Refer to the field 12-066 † † — Refer to the field 13-066 †...

  • Page 215

    (Not effective for PLU 2nd@) number Always “0” No = 0 Commission 1 (Not effective for PLU 2nd@) Yes = 1 (a+b) No = 0 Commission 2 (Not effective for PLU 2nd@) Yes = 2 Always “0” TE-7000S/8000F/8500F Programming Manual P-215...

  • Page 216

    Program 6 Field 11-066 Description Choice Program code Significant Link subdepartment record number (for PLU and PLU 2nd@) numbers Link department record number Significant (for PLU, PLU 2nd@ and subdepartment) numbers Significant Link group record number numbers Field 12-066 Description Choice Program code ::::::...

  • Page 217

    Pulldown group record number (2) Significant (not for PLU 2nd@) numbers : : : Pulldown group record number (3) Significant (not for PLU 2nd@) numbers : : : Pulldown group record number (4) Significant (not for PLU 2nd@) numbers TE-7000S/8000F/8500F Programming Manual P-217...

  • Page 218

    Program 6 7-2-6-5. Function key — Record No. / Key descriptor / Parameter * * Parameter: Refer to the worksheet of each function key on page 120 ~ 136 in PGM 3 mode. 7-2-6-6. Scanning PLU link — Header — Used record No. / Allocated record No. —...

  • Page 219: Keyboard, Memory Allocation

    DL: Daily total / PGM / work area, P1: Periodic 1 total P2: Periodic 2 total, WK: Consolidation work CL: Consolidation area of above file “--” means no file allocation. “*” means the file allocated in the flash memory. — Remaining RAM capacity TE-7000S/8000F/8500F Programming Manual P-219...

  • Page 220

    Program 6 P-220...

  • Page 221

    Index ....................... P-222 Program 3 mode Hierarchy ..................P-225 Program 1 mode Hierarchy ..................P-226 Program 2 mode Hierarchy ..................P-226 Program 6 mode Hierarchy ..................P-227 TE-7000S/8000F/8500F Programming Manual P-221...

  • Page 222: Clerk P, Index

    Index Index delete RF items from guest receipt P-41 department descriptors P-149 department features P-114 department unit price P-166 deposit+ P-126 add mode P-39 deposit- P-126 allow numeric entries (compulsory drawer) P-41 display control P-53 allow to operate n-th menu P-85 display report P-46 allow two consecutive receipts in REF mode P-41 double size letter key P-145...

  • Page 223

    P-136 open 2 P-131 operator X/Z P-132 order character link P-155 order color P-111 order control P-50 order print #1 ~ #7 P-111 origin of reset data to be sent to the master P-47 TE-7000S/8000F/8500F Programming Manual P-223...

  • Page 224

    Index scanning PLU link P-138 schedule P-72, P-200 scheduler P-56 selective item subtotal P-133 sentinel amount P-39 set menu table P-34 set menu/condiment P-51 shift key P-145 shift PLU P-136, P-137 slip P-130 slip/guest P-48 sort by department P-42 sort by group P-42 sort by group/dept with detail P-42 space key P-145 special characters P-157...

  • Page 225: Program 3 Mode Hierarchy

    Full hash item ————————— High amount limit ——————— Low digit limit ————————— Multiple validation ——————— Use main item Amount ————— Use Premium item of set ———— Function key ———————————————————————————— Shift PLU —————————————————————————————— Scanning PLU Link ————————————————————————— Pulldown Group ——————————————————————————— TE-7000S/8000F/8500F Programming Manual P-225...

  • Page 226: Program 1 Mode Hierarchy, Program 2 Mode Hierarchy

    Index Program 1 mode Hierarchy PLU —————————————————————————————————— Unit price/Q’ty ————— Program 1 PLU 2nd @ ————————————————————————————— PLU & PLU 2nd @ ————————————————————————— Subdepartment ——————————————————————————— Department ————————————————————————————— PLU by range ——————————————— Range ————————— PLU 2nd @ by range ———————— Subdepartment by range ——————— Department by range ————————...

  • Page 227: Program 6 Mode Hierarchy

    Clerk detail ——————————— Clerk Key ID —————————— PLU feature PLU 2nd @ feature ————————— Key feature ————————— Subdepartment feature —————— Department feature ——————— Function key feature ——————— Scanning PLU Link ——————— Keyboard —————————————————————————————— Memory allocation —————————————————————————— TE-7000S/8000F/8500F Programming Manual P-227...

  • Page 228

    IR0302-A CASIO COMPUTER CO., LTD. Printed in Japan 6-2, Hon-machi 1-chome Shibuya-ku, Tokyo 151-8543, Japan TE-7000S PGM*E...

This manual also for:

Te-8000f, Te-8500f

Comments to this Manuals

Symbols: 0
Latest comments: