Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for TRENDnet TEW-210APB
Summary of Contents for TRENDnet TEW-210APB
-
Page 1: User Manual
TEW-210APB Wireless Multi-mode AP User Manual Version 1.7.4.5 – Apr 2002... -
Page 2: Table Of Contents
Managing Security ..........9 4.4 Advanced Setting..........10 4.5 Access Control………………………………………12 Change community string ........13 4.7 Reset device …..…………………………………..14 5 Technical Specifications TEW-210APB..15 Standard Specifications ........15 Environmental ............. 15 Power Specifications........... 15 Radio Specifications ........... 15 Specific Features ..........15... -
Page 3: Introduction
These Access Points are connected to a wired network to communicate with each other and with servers and clients on that network. The TEW-210APB Access Point can be connected to a 10/100 Mbps Ethernet network through a RJ45 (UTP) connector. Notice: This version of the TEW-210APB supports AP and Bridging features. -
Page 4: Installation
3. Installation 1. Mount the Access Point firmly to the wall or proper location that is determined during the site survey. 2. Make sure the antennas are in a vertical position (if not, rotate over 90 degrees). 3. Insert the power connector. 4. -
Page 5: Snmp Features
4. SNMP Features You can make use of SNMP utility software for connect TEW-210APB which you want to manage. Supported features: • Restrict the authority of user to access WLAN and this unit. • Support IEEE 802.11 WEP encryption. • Optimizing the radio configuration via assign the independent spectrum. -
Page 6: How To Install And Launch The Snmp Manager
IP address of your pc into 192.168.5.xxx subnet for TEW-210APB configuration. The default IP of TEW-210APB is 192.168.5.100. To make sure your pc and TEW-210APB whether in a same subnet and the connection is well, you can do a test via “ ping “ command. For example, you can employ the following command “... - Page 7 4.1-2 When you got the available AP and press the connect button, there is a pop out window will come out. You should import the community string and assign a role for administration. The default community string is “ public “ and the Authority need to be a “...
-
Page 8: How To Change The Ip Address
4.2 How to change the IP Address If you wish to change the default IP address of TEW-210APB, please click the tab “ Setup “ “ Bridge “ “ IP configuration “ as Figure3. With this table, please change the IP address what you expected. -
Page 9: Managing Security
4.3 Managing Security Maintaining security in a wireless LAN environment is somewhat different from a wired network, because the radio waves do not stop at your office walls. Eavesdropping or unauthorized access from outside and your building can be a serious threat. If you wish to enable the Privacy Options function, please click the “... -
Page 10: Advanced Setting
4.4 Advanced setting You can change the settings such as ESSID, channel, operational mode and so on via the advanced setting. To click the “ Setup ” ” Wireless LAN “ “ Operational Settings “ . Regarding the detail setting and parameters, it will show on the following table. - Page 11 may decline to authenticate with any particular other STA. Shared Key: Shared Key is only available if the WEP option is implemented. Shared Key authentication supports authentication of STAs as either a member of those who know a shared secret key or a member of those who do not.
-
Page 12: Access Control
4.5 Access Control ( Authorized MAC Address ) The IEEE 802.11 standard allows for Access Control rules based on the client station’s hardware address, and is fully implemented by the TEW-210APB. The Mac address table can be specified with a text file format. Then using the “... -
Page 13: Change Community String
4.6 Change community string The default community string is ”public”. All of the setting can be changed only the import string is fit with system. There are two kind of authorities can connect to this unit. One is Administrator the other is general user. The community string can be changed by this pop out window. -
Page 14: Reset Device
4.7 Reset device This unit can be reset to factory defaults by reset hole and the procedure can be done with the following steps. 1.You can reset the Access Point’s settings to factory defaults by pushing a paperclip in the little hole next to the UTP port while the Access Point is on and do not release it right away. -
Page 15: Technical Specifications Tew-210Apb
5 Technical specifications of TEW-210APB 5.1Standards supported − IEEE 802.11 standard for Wireless LAN − All major networking standards (including TCP/IP, NetBEUI, IPX) 5.2 Environmental − Operating temperature (ambient): − 0 ~ 55°C Humidity: − Max. 95% Non-condensing 5.3 Power Specifications −... -
Page 16: Physical Dimensions
Data encryption: − 40-bits WEP Encryption − 128-bits WEP Encryption Utility Software: − SNMP Manager to manage wireless LAN, network connection and client access control 5.6 Physical Dimensions - 103mm x 145mm x 30mm...