1. Manuals
  2. Brands
  3. TRENDnet Manuals
  4. Switch
  5. TEG-S811Fi
  6. User manual

TRENDnet TEG-S811FI User Manual

Hide thumbs Also See for TEG-S811FI:
Table of Contents

Advertisement

Quick Links

Download this manual

Advertisement

Table of Contents
loading

Related Manuals for TRENDnet TEG-S811FI

Summary of Contents for TRENDnet TEG-S811FI

  • Page 2 Notice This manual contents are based on the below table listing software kernel version, hardware version, and firmware version. If your switch functions have any different from the manual contents description, please contact the local sale dealer for more information. Firmware Version V1.08 Kernel Version...

  • Page 3: Fcc Warning

    FCC Warning This Equipment has been tested and found to comply with the limits for a Class-A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

  • Page 4: Table Of Contents

    Content FCC Warning..................i CE Mark Warning ...................i Introduction ................1 Features ....................1 Software Feature.................. 2 Package Contents ................5 Hardware Description .............7 Physical Dimension ................7 Front Panel................... 7 LED Indicators..................8 Rear Panel ................... 9 Desktop Installation ................10 Attaching Rubber Pads ..................10 Power On ...................
  • Page 5 Trunk Commands Set ..................23 VLAN Commands Set ..................24 Spanning Tree Commands Set ................26 QOS Commands Set ..................29 IGMP Commands Set ..................30 Mac / Filter Table Commands Set..............30 SNMP Commands Set ..................31 Port Mirroring Commands Set................34 802.1x Commands Set..................34 TFTP Commands Set ..................37 SystemLog, SMTP and Event Commands Set..........37 SNTP Commands Set ..................39 X-ring Commands Set ..................40...
  • Page 6 SNTP Configuration ................53 IP Security ..................56 User Authentication ................57 Port Statistics ..................58 Port Control ..................59 Port Trunk................... 60 Aggregator setting ....................60 Aggregator Information ..................62 State Activity .......................63 Port Mirroring..................63 Rate Limiting ..................64 VLAN configuration ................66 VLAN configuration - Port-based VLAN ..............66 802.1Q VLAN......................68 802.1Q VLAN......................69...
  • Page 7 X-Ring ....................84 802.1X/Radius Configuration ................86 System Configuration ..................86 802.1x Per Port Configuration ................87 Misc Configuration ...................88 MAC Address Table....................89 Static MAC Address ..................89 MAC Filtering ....................90 All MAC Addresses ..................91 Factory Default ................... 92 Save Configuration ................92 System Reboot................... 93 Troubleshooting ..............94 Incorrect connections .................

  • Page 8: Introduction

    Introduction The 8 10/100TX plus 1 10/100/1000T + 1 MINI GBIC Managed Switch is a multi-port switch that can be used to build high-performance switched workgroup networks. This switch is a store-and-forward device that offers low latency for high-speed networking. The switch is targeted at workgroup, department or backbone computing environment.

  • Page 9: Software Feature

    Support Per port band width control Support Management IP address security Support System Event log Support Port Based VLAN /802.1Q VLAN Support IEEE802.3ad Port trunk with LACP Support Spanning tree protocol STP / Rapid STP QoS method: Port based / Tag based IPv4 ToS/ Ipv4, IPv6 DiffServe Support IEEE 802.1x user authentication Support Broadcast storm filter...
  • Page 10 RFC2233 MIBII RFC 1157 SNMP MIB RFC 1493 Bridge MIB RFC 2674 VLAN MIB RFC 2665 Ethernet like MIB RFC1215 Trap MIB RFC standard RFC 2819 RMON MIB Private MIB RFC2030 SNTP RFC 2821 SMTP RFC 1757 RMON1 MIB RFC 1215 Trap IEEE802.3ad with LACP function Port Trunk Up to 3 trunk groups...
  • Page 11 Port based Quality of Tag based IPv4 Type of service service IPv6 Different service IGMP v1 and v2 compliance IGMP 256 IGMP groups query mode 3 mirroring types: “RX, TX and Both packet” Port Mirror Maximum of port mirror entries is up to 8. ingress and egress MAC address filter Port Security Static source MAC address lock...

  • Page 12: Package Contents

    DHCP Client DHCP DHCP Server Software TFTP firmware upgrade Upgrade Broadcast storm packet filter Packet filter Support 100 entries of MAC address for static MAC Port security and another 100 for MAC filter Support System log record and remote system log System log server Support SNTP to synchronize system clock in...
  • Page 13 Unpack the contents of the 8 10/100TX plus 1 10/100/1000T + 1 MINI GBIC Managed and verify them against the checklist below: Switch 8 10/100TX plus 1 10/100/1000T + 1 MINI GBIC Managed Switch Four Rubber Pads RS-232 cable Power Cord User Manual 8 10/100TX + 1 10/100/1000T Four Rubber Pads...

  • Page 14: Hardware Description

    Hardware Description This section mainly describes the hardware of the 8 10/100TX plus 1 10/100/1000T + 1 MINI GBIC Managed Switch and gives a physical and functional overview on the certain switch. Physical Dimension 8 10/100TX plus 1 10/100/1000T + 1 MINI GBIC Managed Switch’s physical dimensions is 217mm(W) x 140mm(D) x 43mm(H).

  • Page 15: Led Indicators

    connecting to a workstation or PC. Therefore, Auto MDI/MDIX would allow connecting to another switch or workstation without changing non-crossover or crossover cabling. 1 Giga port: 1x 10/100/1000TX N-Way auto-sensing for 10/100/1000 connection. 1 Mini GBIC port: one optional mini GBIC module port LED Indicators The LED Indicators display real-time information of systematic operation status.

  • Page 16: Rear Panel

    No device attached. The port is operating in Full-duplex mode Orange FDX/COL Collision of packets occurs Blinks In half-duplex mode In 1000Mbps connection speed Green In 100Mbps connection speed 1000M (G1 port) Orange No device attached The port is connecting with the device Green LNK/ACT (G1 port) The port is receiving or transmitting data...

  • Page 17: Desktop Installation

    AC in the voltage range of AC 100-240V and Frequency of 50-60Hz. The Rear Panel of the 8 10/100TX plus 1 10/100/1000T + 1 MINI GBIC Managed Switch Desktop Installation Set the switch on a sufficiently large flat space with a power outlet nearby. The surface where you put the switch should be clean, smooth, level and sturdy.

  • Page 18: Network Application

    Network Application This section provides a few samples of network topology in which the switch is used. In general, the 8 10/100TX plus 1 10/100/1000T + 1 MINI GBIC Managed Switch is designed as a segment switch which with its large address table (8k MAC address) and high performance, it is ideal for interconnecting networking segments.

  • Page 19: Segment Bridge

    Small Workgroup application Segment Bridge For enterprise networks where large data broadcasts are constantly processed, this switch is an ideal solution for department users to connect to the corporate backbone. In the illustration below, two Ethernet switches with PCs, print server, and local server attached, are both connect to the switch.
  • Page 20 Segment Bridge application...

  • Page 21: Console Management

    Console Management Login in the Console Interface When the connection between switch and PC is ready, and then turn on the PC and run a terminal emulation program or Hyper Terminal and configure its communication parameters to match the following default characteristics of the console port: Baud Rate: 9600 bps Data Bits: 8 Parity: none...

  • Page 22: Cli Management

    Console login screen CLI Management The system supports console management – CLI command. After you login to the system, you will see a command prompt. To enter CLI management interface, enter “enable” command. The following table lists the CLI commands and description.

  • Page 23: Commands Level

    CLI command interface Commands Level Access Exit Modes Prompt About This Mode1 Method Method The user commands available at the user level are a subset of Begin a Enter those available at the User session with switch> logout or privileged level. EXEC your switch.
  • Page 24 EXEC mode. • Display advance function status • Save configures Enter the To exit to configure Use this mode to Global privileged command switch configure parameters Configura EXEC while in (config)# that apply to your tion mode, enter privileged switch as a whole. exit or end EXEC mode.

  • Page 25: Commands Set List

    Commands Set List System Commands Set Trendnet Commands Level Description Example show config Show switch switch>show config configuration show terminal Show console switch#show terminal information write memory Save user switch#write memory configuration into permanent memory (flash rom) system name Configure system...
  • Page 26 reload Halt and perform a cold switch(config)#reload restart default Restore to default switch(config)#default admin username Changes a login switch(config)#admin username [Username] username. xxxxxx (maximum 10 words) admin password Specifies a password switch(config)#admin password (maximum 10 words) [Password] xxxxxx show admin Show administrator switch#show admin information...

  • Page 27: Port Commands Set

    Disable IP security of switch(config)#no security http HTTP server no security telnet Disable IP security of switch(config)#no security telnet telnet server Port Commands Set Trendnet Commands Level Description Example interface fastEthernet Choose the port for switch(config)#interface [Portid] modification. fastEthernet 2...
  • Page 28 operation for Fast Ethernet. speed Use the speed switch(config)#interface [10|100|1000|auto] configuration fastEthernet 2 command to specify switch(config-if)#speed 100 the speed mode of operation for Fast Ethernet., the speed can’t be set to 1000 if the port isn’t a giga port.. Disable flow control of switch(config-if)#no flowcontrol no flowcontrol...
  • Page 29 multicast frame” broadcast-multicast bandwidth type Set interface ingress switch(config)#interface broadcast-only limit frame type to “only fastEthernet 2 accept broadcast switch(config-if)#bandwidth type frame” broadcast-only Set interface input switch(config)#interface bandwidth in [Value] bandwidth. Rate fastEthernet 2 Range is from 100 switch(config-if)#bandwidth in 100 kbps to 102400 kbps or to 256000 kbps for giga ports,...

  • Page 30: Trunk Commands Set

    2 (config-if)#show interface accounting no accounting Clear interface switch(config)#interface accounting information fastEthernet 2 switch(config-if)#no accounting Trunk Commands Set Trendnet Commands Level Description Example aggregator priority Set port group system switch(config)#aggregator priority priority [1~65535] aggregator activityport Set activity port switch(config)#aggregator...

  • Page 31: Vlan Commands Set

    [GroupID] function of trunk group no aggregator group Remove a trunk group switch(config)#no aggreator [GroupID] group 2 VLAN Commands Set Trendnet Commands Level Description Example vlan database Enter VLAN configure switch#vlan database mode Vlanmode To set switch VLAN...
  • Page 32 [portbase| 802.1q | mode. gvrp] switch(vlan)#vlanmode 802.1q switch(vlan)#vlanmode gvrp No VLAN Switch(vlan)#no vlan no vlan Ported based VLAN configuration vlan port-based Add new port based switch(vlan)#vlan port-based VALN grpname grpname test grpid 2 port 2-4 [Group Name] grpid switch(vlan)#vlan port-based [GroupID] grpname test grpid 2 port 2,3,4 port...

  • Page 33: Spanning Tree Commands Set

    Show VLAN switch(vlan)#show vlan 23 information show vlan no vlan group Delete port base group switch(vlan)#no vlan group 2 [GroupID] Spanning Tree Commands Set Trendnet Commands Level Description Example spanning-tree enable Enable spanning tree switch(config)#spanning-tree enable spanning-tree priority Configure spanning switch(config)#spanning-tree...
  • Page 34 [seconds] max-age global max-age 15 configuration command to change the interval between messages the spanning tree receives from the root switch. If a switch does not receive a bridge protocol data unit (BPDU) message from the root switch within this interval, it recomputed the Spanning Tree Protocol (STP)
  • Page 35 forwarding time determines how long each of the listening learning states last before the port begins forwarding. stp-path-cost Use the spanning-tree switch(config)#interface [1~200000000] cost interface fastEthernet 2 configuration switch(config-if)#stp-path-cost 20 command to set the path cost for Spanning Tree Protocol (STP) calculations.

  • Page 36: Qos Commands Set

    False show spanning-tree Displays a summary of switch>show spanning-tree the spanning-tree states. no spanning-tree Disable spanning-tree. switch(config)#no spanning-tree QOS Commands Set Trendnet Commands Level Description Example qos policy Select QOS policy switch(config)#qos policy [weighted-fair|strict] scheduling weighted-fair Setting of QOS priority...

  • Page 37: Igmp Commands Set

    Disable QoS function switch(config)#no qos IGMP Commands Set Trendnet Commands Level Description Example igmp enable Enable IGMP switch(config)#igmp enable snooping function Igmp-query auto Set IGMP query to switch(config)#Igmp-query auto auto mode Igmp-query force Set IGMP query to switch(config)#Igmp-query force...

  • Page 38: Snmp Commands Set

    [MAC] (filter) 000012348678 no mac-address-table Remove dynamic entry switch(config)#no of MAC address table mac-address-table SNMP Commands Set Trendnet Commands Level Description Example snmp system-name Set SNMP agent switch(config)#snmp [System Name] system name system-name l2switch Set SNMP agent...
  • Page 39 community and community string trap-version v1 [Community-string] (remove) trap-version Switch(config)# [v1|v2c] no snmp-server host 192.168.1.50 snmpv3 context-name Configure the context switch(config)#snmpv3 [Context Name ] name context-name Test snmpv3 user Configure the switch(config)#snmpv3 user [User Name] userprofile for test01 group G1 password SNMPV3 agent.
  • Page 40 [Excluded|Included] sub-oid [OID] show snmp Show SNMP switch#show snmp configuration no snmp Remove the specified switch(config)#no snmp community-strings community. community-strings public [Community] no snmp-server host Remove the SNMP switch(config)#no snmp-server [Host-address] server host. 192.168.1.50 no snmpv3 user Remove specified user switch(config)#no snmpv3 user [User Name] of SNMPv3 agent.

  • Page 41: Port Mirroring Commands Set

    [OID] Port Mirroring Commands Set Trendnet Commands Level Description Example monitor rx Set RX destination port switch(config)#monitor rx of monitor function monitor tx Set TX destination port switch(config)#monitor tx of monitor function show monitor Show port monitor switch#show monitor information...
  • Page 42 8021x system serverport Use the 802.1x system switch(config)# 8021x system [port ID] server port global serverport 1815 configuration command to change the radious server port 8021x system Use the 802.1x system switch(config)# 8021x system accountport account port global accountport 1816 [port ID] configuration command to change...
  • Page 43 supportimeout [sec.] supp timeout global supportimeout 20 configuration command to set the supplicant timeout. Use the 802.1x misc switch(config)#8021x misc 8021x misc servertimeout [sec.] server timeout global servertimeout 20 configuration command to set the server timeout. Use the 802.1x misc switch(config)# 8021x misc 8021x misc maxrequest [number]...

  • Page 44: Tftp Commands Set

    TFTP Commands Set Trendnet Commands Level Description Defaults Example backup Save configuration to switch(config)#backup flash:backup_cfg TFTP and need to flash:backup_cfg specify the IP of TFTP server and the file name of image. restore flash:restore_cfg Get configuration from switch(config)#restore TFTP server and need to...
  • Page 45 [IP address] server IP 192.168.1.5 smtp authentication Enable SMTP switch(config)#smtp authentication authentication smtp account Configure switch(config)#smtp account User [account] authentication account smtp password Configure switch(config)#smtp password [password] authentication password smtp rcptemail Configure Rcpt e-mail switch(config)#smtp rcptemail 1 [Index] [Email address] Address Alert@test.com show smtp...

  • Page 46: Sntp Commands Set

    SMTP fastethernet 3 switch(config-if)#no event smtp show systemlog Show system log client switch#show systemlog & server information SNTP Commands Set Trendnet Commands Level Description Example sntp enable Enable SNTP function switch(config)#sntp enable Enable daylight saving switch(config)#sntp daylight sntp daylight time, if SNTP function is inactive, this command can’t be...

  • Page 47: X-Ring Commands Set

    Disable SNTP function switch(config)#no sntp no sntp daylight Disable daylight saving switch(config)#no sntp daylight time X-ring Commands Set Trendnet Commands Level Description Example Xring enable Enable X-ring switch(config)#Xring enable Enable ring master switch(config)#Xring master Xring master...
  • Page 48 [Coupling Port] Port Xring controlport Configure Control Port switch(config)#Xring controlport 2 [Control Port] Xring homingport Configure Dual switch(config)#Xring homingport [Dual Homing Port] Homing Port show Xring Show the information switch#show Xring of X - Ring Disable X-ring switch(config)#no X ring no Xring no Xring master Disable ring master...

  • Page 49: Web-Based Management

    Web-Based Management This section introduces the configuration and functions of the Web-Based management. About Web-based Management On the CPU board of the switch, there is an embedded HTML web site residing in flash memory, which offers advanced management features and allow users to manage the switch from anywhere on the network through a standard browser such as Microsoft Internet Explorer.

  • Page 50: System Information

    Click “Enter” or” OK”, then the home screen of the Web-based management appears right after Main interface System Information Assign the system name and location and view the system information System Name: Assign the system name of the switch (The maximum length is 64 bytes) System Description: Displays the description of switch(Read only cannot be modified)

  • Page 51: Ip Configuration

    And than, click Apply System Information interface IP Configuration User can configure the IP Settings and DHCP client function DHCP: To disable or enable the DHCP client function IP Address: Assign the switch IP address. The default IP is 192.168.16.1 Subnet Mask: Assign the switch IP subnet mask Gateway: Assign the switch gateway.

  • Page 52: Dhcp Configuration

    Reboot the switch after reset the IP address IP Configuration interface DHCP Configuration It short for Dynamic Host Configuration Protocol that is a protocol for assigning dynamic IP addresses to devices on a network. With dynamic addressing, a device can have a different IP address every time it connects to the network.

  • Page 53: Dhcp Client Entries

    will be the DHCP server on your local network Low IP Address: The dynamic IP range. Low IP address is the beginning of the dynamic IP range. For example: dynamic IP range is from 192.168.1.100 ~ 192.168.1.200. 192.168.1.100 will be the Low IP address High IP Address: The dynamic IP range.

  • Page 54: Port And Ip Bindings

    DHCP Client Entries interface Port and IP Bindings Assign the dynamic IP address to the port. When the device is connecting to the port and asking for IP assigning, the system will assign the IP address that has been assigned before to the connected device.

  • Page 55: Tftp - Update Firmware

    TFTP - Update Firmware It provides the functions to allow you to update the switch firmware. Before updating, make sure the TFTP server is ready and the firmware image is on the TFTP server. TFTP Server IP Address: Key in the TFTP server IP Firmware File Name: The name of firmware image And then, click Apply...

  • Page 56: Tftp - Backup Configuration

    TFTP - Backup Configuration Save current EEPROM value from the switch to TFTP server, then go to the TFTP restore configuration page to restore the EEPROM value. TFTP Server IP Address: Key in the TFTP server IP Backup File Name: Key in the file image name And then, click Apply Backup Configuration interface...

  • Page 57: System Event Log - Smtp Configuration

    (when Email Alert enabled, this function will then be available).. Mail Account: set up the email account, e.g. support@trendnet.com, to receive the alert. It must be an existing email account on the mail server, which you had set up in...

  • Page 58: System Event Log - Event Configuration

    SMTP Server IP Address column. Password: The email account password. Confirm Password: reconfirm the password. Rcpt e-mail Address 1 ~ 6: you can assign up to 6 e-mail accounts also to receive the alert. Click Apply SMTP Configuration interface System Event Log - Event Configuration You can select the system log events and SMTP events.
  • Page 59 System event selection: 4 selections – Device cold start, Device warm start, SNMP Authentication Failure, and X-ring topology change. Mark the checkbox to select the event. When selected events occur, the system will issue the logs. Device cold start: when the device executes cold start action, the system will issue a log event.

  • Page 60: Sntp Configuration

    Event Configuration interface Port event selection: select the per port events and per port SMTP events. It has 3 selections – Link UP, Link Down, and Link UP & Link Down. Disable means no event is selected. Link UP: the system will issue a log message when port connection is up only. Link Down: the system will issue a log message when port connection is down only.
  • Page 61 CDT - Central Daylight CST - Central Standard -6 hours 6 am MDT - Mountain Daylight MST - Mountain Standard -7 hours 5 am PDT - Pacific Daylight PST - Pacific Standard -8 hours 4 am ADT - Alaskan Daylight ALA - Alaskan Standard -9 hours 3 am...
  • Page 62 USSR Zone 7 JST - Japan Standard, +9 hours 9 pm USSR Zone 8 EAST - East Australian Standard GST +10 hours 10 pm Guam Standard, USSR Zone 9 IDLE - International Date Line NZST - New Zealand +12 hours Midnight Standard NZT - New Zealand...

  • Page 63: Ip Security

    SNTP Configuration interface IP Security IP security function allows user to assign 10 specific IP addresses that have permission to access the switch through the web browser for the securing switch management. IP Security Mode: when this option is in Enable mode, the Enable HTTP Server and Enable Telnet Server check boxes will then be available.

  • Page 64: User Authentication

    IP Security interface User Authentication Change web management login user name and password for the management security issue User name: Key in the new user name(The default is “root”) Password: Key in the new password(The default is “root”) Confirm password: Re-type the new password And then, click Apply...

  • Page 65: Port Statistics

    User Authentication interface Port Statistics The following information provides the current port statistic information. Port: The port number. Type: Displays the current speed of connection to the port. Link: The status of linking—‘Up’ or ‘Down’. State: It’s set by Port Control. When the state is disabled, the port will not transmit or receive any packet.

  • Page 66: Port Control

    Port Statistics interface Port Control In Port control, you can view every port status that depended on user setting and the negotiation result. Port: select the port that you want to configure. State: Current port status. The port can be set to disable or enable mode. If the port setting is disable then will not receive or transmit any packet.

  • Page 67: Port Trunk

    Port Control interface Port Trunk The Link Aggregation Control Protocol (LACP) provides a standardized means for exchanging information between Partner Systems on a link to allow their Link Aggregation Control instances to reach agreement on the identity of the Link Aggregation Group to which the link belongs, move the link to that Link Aggregation Group, and enable its transmission and reception functions in an orderly manner.
  • Page 68 System Priority: a value used to identify the active LACP. The switch with the lowest value has the highest priority and is selected as the active LACP. Group ID: There are three trunk groups to provide configure. Choose the "Group ID" and click Select LACP: If enable, the group is LACP static trunk group.

  • Page 69: Aggregator Information

    Port Trunk—Aggregator Setting interface Aggregator Information When you have setup the LACP aggregator, you will see the related information here. Port Trunk – Aggregator Information interface...

  • Page 70: State Activity

    State Activity When you had setup the LACP aggregator, you can configure port state activity. You can mark or un-mark the port. When you mark the port and click button the port state Apply activity will change to Active. Opposite is Passive. Active: The port automatically sends LACP protocol packets.

  • Page 71: Rate Limiting

    The Port mirroring is a method for monitor traffic in switched networks. Traffic through ports can be monitored by one specific port. That means traffic goes in or out monitored (source) ports will be duplicated into mirror (destination) port. Destination Port: There is only one port can be selected to be destination (mirror) port for monitoring both RX and TX traffic which come from source port.
  • Page 72 Ingress Limit Frame type: select the frame type that wants to filter. The frame types have 4 options for selecting: All, Broadcast/Multicast/Flooded Unicast, Broadcast/Multicast and Broadcast only. Broadcast/Multicast/Flooded Unicast, Broadcast/Multicast and Bbroadcast only types are only for ingress frames. The egress rate only supports All type. Rate Limiting interface All the ports support port ingress and egress rate control.

  • Page 73: Vlan Configuration

    [NOTE] Rate Range is from 64 kbps to 102400 kbps (250000 kbps for giga ports) and zero means no limit VLAN configuration A Virtual LAN (VLAN) is a logical network grouping that limits the broadcast domain, which would allow you to isolate network traffic, so only the members of the VLAN will receive traffic from the same members of VLAN.
  • Page 74 VLAN-tagging is ignored. In order for an end station to send packets to different VLAN groups, it itself has to be either capable of tagging packets it sends with VLAN tags or attached to a VLAN-aware bridge that is capable of classifying and tagging the packet with different VLAN ID based on not only default PVID but also other information about the packet, such as the protocol.
  • Page 75 VLAN—Port Based Add interface You will see the VLAN displays. button to delete unwanted VLAN. Delete button to modify existing VLAN group. Edit [NOTE] Remember to execute the “Save Configuration” action, otherwise the new configuration will lose when switch power off.

  • Page 76: 802.1Q Vlan

    802.1Q VLAN Tagged-based VLAN is an IEEE 802.1Q specification standard. Therefore, it is possible to create a VLAN across devices from different switch venders. IEEE 802.1Q VLAN uses a technique to insert a “tag” into the Ethernet frames. Tag contains a VLAN Identifier (VID) that indicates the VLAN numbers.

  • Page 77: 802.1Q Configuration

    802.1Q Configuration Enable GVRP Protocol: check the check box to enable GVRP protocol. Select the port that wants to configure. Link Type: there are 3 types of link type. Access Link: single switch only, allow user to group ports by setting the same VID.
  • Page 78 Group Configuration interface You can Change the VLAN group name and VLAN ID. Click Apply Group Configuration interface...

  • Page 79: Rapid Spanning Tree

    Rapid Spanning Tree The Rapid Spanning Tree Protocol (RSTP) is an evolution of the Spanning Tree Protocol and provides for faster spanning tree convergence after a topology change. The system also supports STP and the system will auto detect the connected device that is running STP or RSTP protocol.

  • Page 80: Rstp - Port Configuration

    RSTP System Configuration interface RSTP - Port Configuration You can configure path cost and priority of every port. 1. Select the port in Port column. 1. Path Cost: The cost of the path to the other bridge from this transmitting bridge at the specified port.

  • Page 81: Snmp Configuration

    allows the P2P status of the link to be manipulated administratively. True is P2P enabling. False is P2P disabling. 4. Edge: The port directly connected to end stations cannot create bridging loop in the network. To configure the port as an edge port, set the port to “True” status. 5.

  • Page 82: System Configuration

    traps or change notices from network devices implementing SNMP. System Configuration Community Strings You can define new community string set and remove unwanted community string. String: fill the name of string. RO: Read only. Enables requests accompanied by this string to display MIB-object information.

  • Page 83: Trap Configuration

    SNMP System Configuration interface Trap Configuration A trap manager is a management station that receives traps, the system alerts generated by the switch. If no trap manager is defined, no traps will issue. Create a trap manager by entering the IP address of the station and a community string. To define management stations as trap manager and enter SNMP community strings and selects the SNMP version.

  • Page 84: Snmpv3 Configuration

    Trap Managers interface SNMPV3 Configuration Configure the SNMP V3 function. Context Table Configure SNMP v3 context table. Assign the context name of context table. Click add context name. Click to remove unwanted context name. Remove User Profile Configure SNMP v3 user table.. User ID: set up the user name.
  • Page 85 SNMP V3 configuration interface...
  • Page 86 Group Table Configure SNMP v3 group table. Security Name (User ID): assign the user name that you have set up in user table. Group Name: set up the group name. Click to add context name. Click to remove unwanted context name. Remove Access Table Configure SNMP v3 access table.

  • Page 87: Qos Configuration

    Click to add context name. Click to remove unwanted context name. Remove QoS Configuration You can configure Qos policy and priority setting, per port priority setting, COS and TOS setting. QoS Policy and Priority Type Qos Policy: select the Qos policy rule. Using the 8,4,2,1 weight fair queue scheme: The switch will follow 8:4:2:1 rate to process priority queue from High to lowest queue.
  • Page 88 rule. TOS first: the port priority will follow the TOS priority first, and the other priority rule. Click Apply QoS Configuration interface...

  • Page 89: Port Base Priority

    Port Base Priority Configure per port priority level. Port 1 ~ Port 8 & G1~G2: each port has 4 priority levels – High, Middle, Low, and Lowest. Click Apply COS Configuration Set up the COS priority level. COS priority: Set up the COS priority level 0~7 –High, Middle, Low, Lowest. Click Apply TOS Configuration...

  • Page 90: Igmp Configuration

    IGMP Configuration The Internet Group Management Protocol (IGMP) is an internal protocol of the Internet Protocol (IP) suite. IP manages multicast traffic by using switches, routers, and hosts that support IGMP. Enabling IGMP allows the ports to detect IGMP queries and report packets and manage IP multicast traffic through the switch.

  • Page 91: X-Ring

    IGMP Configuration interface X-Ring X-Ring provides a faster redundant recovery than Spanning Tree topology. The action is similar to STP or RSTP, but the algorithms not the same. In the X-Ring topology, every switch should enable X-Ring function and assign two member ports in the ring.
  • Page 92 redundant backup function and dual homing function that prevent connection lose between X-Ring group and upper level/core switch. Enable X-Ring: To enable the X-Ring function. Marking the check box to enable the X-Ring function. Enable Ring Master: Mark the check box for enabling this machine to be a ring master.

  • Page 93: 802.1X/Radius Configuration

    [NOTE] When the X-Ring function enable, user must disable the RSTP. The X-Ring function and RSTP function cannot exist at the same time. Remember to execute the “Save Configuration” action, otherwise the new configuration will lose when switch power off. Security In this section, you can configure 802.1x and MAC address table.

  • Page 94: 802.1X Per Port Configuration

    Click Apply 802.1x System Configuration interface 802.1x Per Port Configuration You can configure 802.1x authentication state for each port. The State provides Disable, Accept, Reject and Authorize. Use “Space” key change the state value. Reject: the specified port is required to be held in the unauthorized state. Accept: the specified port is required to be held in the Authorized state.

  • Page 95: Misc Configuration

    802.1x Per Port Setting interface Misc Configuration Quiet Period: set the period during which the port doesn’t try to acquire a supplicant. TX Period: set the period the port wait for retransmit next EAPOL PDU during an authentication session. Supplicant Timeout: set the period of time the switch waits for a supplicant response to an EAP request.

  • Page 96: Mac Address Table

    Click Apply 802.1x Misc Configuration interface MAC Address Table Use the MAC address table to ensure the port security. Static MAC Address You can add a static MAC address; it remains in the switch's address table, regardless of whether the device is physically connected to the switch. This saves the switch from having to re-learn a device's MAC address when the disconnected or powered-off device is active on the network again.

  • Page 97: Mac Filtering

    If you want to delete the MAC address from filtering table, select the MAC address and click Delete Static MAC Addresses interface MAC Filtering By filtering MAC address, the switch can easily filter pre-configure MAC address and reduce the un-safety. You can add and delete filtering MAC address.

  • Page 98: All Mac Addresses

    MAC Filtering interface MAC Address: Enter the MAC address that you want to filter. Click If you want to delete the MAC address from filtering table, select the MAC address and click Delete All MAC Addresses You can view the port that connected device’s MAC address and related devices’ MAC address.

  • Page 99: Factory Default

    All MAC Address interface Factory Default Reset switch to default configuration. Click Reset to reset all configurations to the default value. Factory Default interface Save Configuration Save all configurations that you have made in the system. To ensure the all configuration...

  • Page 100: System Reboot

    will be saved. Click to save the all configuration to the flash memory. Save Save Configuration interface System Reboot Reboot the switch in software reset. Click to reboot the system. Reboot System Reboot interface...

  • Page 101: Troubleshooting

    Troubleshooting This section is intended to help solve the most common problems on the 8 10/100TX plus 1 10/100/1000T + 1 MINI GBIC Managed Switch. Incorrect connections The switch port can automatically detect straight or crossover cable when you link switch with other Ethernet device.

  • Page 102: Improper Network Topologies

    Improper Network Topologies It is important to make sure that you have a valid network topology. Common topology faults include excessive cable length and too many repeaters (hubs) between end nodes. In addition, you should make sure that your network topology contains no data path loops. Between any two ends nodes, there should be only one active cabling path at any time.

  • Page 103: Technical Specification

    Technical Specification This section provides the specifications of 8 10/100TX plus 1 10/100/1000T + 1 MINI GBIC Managed Switch. IEEE 802.3 10Base-T Ethernet IEEE 802.3u 100Base-TX IEEE802.3ab 1000Base-T IEEE802.3z Gigabit fiber IEEE802.3x Flow Control and Back Pressure Standard IEEE802.3ad Port trunk with LACP IEEE802.1d Spanning Tree/ IEEE802.1w Rapid Spanning Tree IEEE802.1p Class of Service...
  • Page 104 10/100TX: 8 x ports RJ-45 with Auto MDI/MDI-X function 10/100/1000T: 1 x ports RJ-45 with Auto MDI/MDI-X Connector function Gigabit fiber: 1 x Mini-GBIC RS-232 DB-9 Female connector for switch management Store and forward switch architecture Switch architecture System throughput up to 8.3Mpps Back-plane 5.6Gbps MAC address...
  • Page 105 Dimensions 217mm(W) x 140mm(D) x 43mm(H) FCC Class A, CE Safety CE/EN60950-1...

  • Page 106: Appendix

    Appendix Console Port Pin Assignments The DB-9 serial port on the switch is used to connect to the switch for out-of-band console configuration. The console menu-driven configuration program can be accessed from a terminal or a PC running a terminal emulation program. The pin assignments used to connect to the serial port are provided in the following tables.

  • Page 107: Cables

    Console Port to 9-Pin DTE Port on PC Switch’s 9-Pin Serial CCITT Signal PC’s DTE Port Port 9-Pin 2 RXD <---------RXD ------------ 3 TxD 3 TXD -----------TXD ----------> 2 RxD 5 SGND -----------SGND ---------- 5 SGND Cables The RJ-45 ports on the switch support automatic MDI/MDI-X operation, so you can use standard straight-through twisted-pair cables to connect to any other network device (PCs, servers, switches, routers, or hubs).
  • Page 108 RJ-45 Pin Assignments Pin Number Assignment [NOTE] “+” and “-” signs represent the polarity of the wires that make up each wire pair. All ports on this switch support automatic MDI/MDI-X operation, you can use straight-through cables for all network connections to PCs or servers, or to other switches or hubs.

Table of Contents