TRENDnet TEG-424WS User Manual
  1. Manuals
  2. Brands
  3. TRENDnet Manuals
  4. Switch
  5. TEG-424WS
  6. User manual

TRENDnet TEG-424WS User Manual

Hide thumbs Also See for TEG-424WS:
Table of Contents

Advertisement

Quick Links

Download this manual

Advertisement

Table of Contents
loading

Related Manuals for TRENDnet TEG-424WS

Summary of Contents for TRENDnet TEG-424WS

  • Page 2: Fcc Warning

    FCC Warning This equipment has been tested and found to comply with the regulations for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
  • Page 3 (Tmra). b) Reduced Air Flow- Installation of the equipment in a rack should be such that the amount of air flow required for safe operation of the equipment is not compromised. c) Mechanical Loading- mounting of the equipment in the rack should be such that a hazardous condition is not achieved due to uneven mechanical loading.

  • Page 5: Table Of Contents

    Front Panel ..................19 Rear Panel ..................20 Understanding LED Indicators ............21 Power and System LEDs ............... 21 100BASE-TX Port 1~24 Status LEDs ........... 22 Combo 1000BASE-T/mini-GBIC Port 25~26 Status LEDs ..22 1000BASE-T Port 27~28 Status LEDs .......... 23...
  • Page 6 Configuration ..................24 Installing the Web Management Utility ......... 24 Discovery List ................25 Monitor List ................... 26 Device Setting ................28 Toolbar ................... 30 Configuring the Switch ..............31 Login ....................31 Setup Setting .................. 33 Port Settings ................33 IEEE 802.1Q VLAN ..............
  • Page 7 Password Setting ................ 66 Statistic ..................67 Factory Reset ................69 Backup Setting ................69 Firmware Upload ............... 70 System Reboot ................70 Logout ..................71 Technical Specifications ..............72...

  • Page 9: About This Guide

    10/100Mbps Web Smart Switch w/ 4 Gigabit Ports and 2 Mini-GBIC slots. Terms/Usage In this guide, the term “Switch” (first letter upper case) refers to your TEG-424WS 24-Port 10/100Mbps Web Smart Switch w/ 4 Gigabit Ports and 2 Mini-GBIC slots, and “switch” (first letter lower case)

  • Page 11: Introduction

    The increased speed and extra bandwidth offered by Gigabit Ethernet is essential to coping with the network bottlenecks that frequently develop as computers and their busses get faster and more users use applications that generate more traffic. Upgrading key components,...

  • Page 12: Fast Ethernet Technology

    In addition, the phenomenal bandwidth delivered by Gigabit Ethernet is the most cost-effective method to take advantage of today and tomorrow’s rapidly improving switching and routing internetworking technologies. And with expected advances in the coming years in silicon technology and digital signal processing that will enable...
  • Page 13 Routers have also been used to segment local area networks, but the cost of a router, the setup and maintenance required make routers relatively impractical. Today switches are an ideal...

  • Page 14: Vlan (Virtual Local Area Network)

    VLAN (Virtual Local Area Network) A VLAN is a group of end-stations that are not constrained by their physical location and can communicate as if a common broadcast domain, a LAN. The primary utility of using VLAN is to reduce latency and need for routers, using faster switching instead.
  • Page 15 Up to 8K unicast addresses entities per device, self-learning, and table aging 128 KBytes packet buffer Supports IEEE 802.3x flow control for full-duplex mode ports Supports IEEE 802.1Q VLAN Supports IEEE 802.1p Priority Queues Supports Static Port Trunk Supports IGMP Snooping Supports SNMP for RFC1213 MIB II and Private MIB Supports IEEE 802.1D Spanning Tree...

  • Page 16: Unpacking And Installation

    Specifications for the acceptable temperature and humidity operating ranges. Install the Switch in a site free from strong electromagnetic field generators (such as motors), vibration, dust, and direct exposure to sunlight. Leave at least 10cm of space at the front and rear of the hub for ventilation.

  • Page 17: Rack Mounting

    Install the Switch on a sturdy, level surface that can support its weight, or in an EIA standard-size equipment rack. For information on rack installation, see the next section, Rack Mounting. When installing the Switch on a level surface, attach the rubber feet to the bottom of each device.

  • Page 18: Connecting Network Cable

    Figure 3. Mount the Switch in the rack Connecting Network Cable The Switch supports 24-port 10/100Mbps 100BASE-TX Fast Ethernet and it runs both in half and full duplex mode using two pair of Category 5 cable. The Switch also supports 4-port 10/100/1000Mbps 1000BASE-T...

  • Page 19: Ac Power

    AC Power The Switch used the AC power supply 100-240V AC, 50-60 Hz. The power switch is located at the rear of the unit adjacent to the AC power connector and the system fan. The switch’s power supply will adjust to the local power source automatically and may be turned on...

  • Page 21: Identifying External Components

    10/100/1000Mbps and auto MDI/MDIX crossover detection function, this function gives true “plug and play” capability, just need to plug-in the network cable to the hub directly and don’t care if the end node is NIC (Network Interface Card) or switch and hub.

  • Page 22: Rear Panel

    RJ45 port will be disabled. Reset: The Reset button is to reset all the setting back to the factory default. Note: Be sure that you recorded the setting of your device, all current settings will be erased when pressing the “Reset” button.

  • Page 23: Understanding Led Indicators

    Power and System LEDs POWER: Power Indicator : When the Power LED lights on, the Switch is receiving power. : When the Power turns off or the power cord has improper connection. SYSTEM: Management Indicator Blinking : When the CPU is working, the System LED is blinking.

  • Page 24: 100Base-Tx Port 1~24 Status Leds

    Ethernet network. : No link. 100Mbps : When the 100Mbps LED lights on, the respective port is connected to a 100Mbps Fast Ethernet network. : When the respective port is connected to a 10Mbps Ethernet network...

  • Page 25: 1000Base-T Port 27~28 Status Leds

    100Mbps When the 100Mbps LED lights on, the respective port is connected to a 100Mbps Fast Ethernet network. When the respective port is connected to a 10Mbps Ethernet or 1000Mbps Gigabit Ethernet network. mini-GBIC When the mini-GBIC LED lights on, the respective port is inserted mini-GBIC module.

  • Page 26: Configuration

    CONFIGURATION Through the Web Browser you can configure the Switch such as VLAN, Port Trunking, Jumbo Frame… etc. With the attached Web Management Utility, you can easily discover all the Web Management Switch, assign the IP Address, changing the password and upgrading the new firmware.

  • Page 27: Discovery List

    By pressing the “Discover” button, you can list all the Web Management devices in the discovery list. Double click or press the “Add to monitor list” button to select a device from the Discovery List to the Monitor List.

  • Page 28: Monitor List

    Gateway: Shows the Gateway set of the device. Monitor List All the Web Smart Device in the Monitor List can be monitored; you can also receive the trap and show the status of the device. System word definitions in the Monitor List: S: Shows the system symbol of the Web-Smart device, represent for device system is not alive.
  • Page 29 Figure 9. Trap Information Note: In order to receive Trap information, the switch has to be configured with Trap IP and Trap Events in Web browser, which are available in the Trap Setting Menu (see Page 65 for detail). Add Item: To add a device to the Monitor List manually, enter the IP...

  • Page 30: Device Setting

    Select the device in the Discovery list or Monitor List and press this button, then the Configuration Setting window will pop out as Figure 10, after filling up the data that you want to change, you must fill up the password and press the “Set” to process the data changed immediately.
  • Page 31 Figure 11. Password Change Firmware Upgrade: When the device has a new function, there will be a new firmware to update the device, use this function to update. Select the path of where the firmware updated firmware is located by clicking “Browse”.

  • Page 32: Toolbar

    Choose 15 secs, 30 secs, 1 min, 2 min and 5 min to select the time of monitoring. In the “Help TAB”, there is About function, it will show the version...

  • Page 33: Configuring The Switch

    Before you configure this device, note that when the Web Smart Switch is configured through an Ethernet connection, make sure the manager PC must be set on same the IP network. For example, when the default network address of the default IP address of the Web Smart Switch is 192.168.0.1, then the manager PC should be set at...
  • Page 34 Figure 14. After entering the password, the main page comes up, the screen will display the device status. Figure 15 System Information...

  • Page 35: Setup Setting

    Priority, Broadcast Strom Control Setting in Setup menu. Port Settings In Port Settings menu (Figure 16), this page will show each port’s status, selected drop down menu to set each port’s Speed, and QoS priority then press “Apply” button to activate changes. To refresh the information table to view the latest port setting and Link Status, press the Refresh button.

  • Page 36: Ieee 802.1Q Vlan

    802.1p Default Priority. IEEE 802.1Q VLAN A VLAN is a group of ports that can be anywhere in the network, but communicate as though they were in the same area. VLANs can be easily organized to reflect department groups (such as R&D, Marketing), usage groups (such as e-mail), or multicast groups...
  • Page 37 “Enabled” radio button and Apply it to submit the Asymmetric VLAN function. Figure 17. Enabled Asymmetric VLAN function Figure 18. Change setting warning message Note: The Settings of VLAN, IGMP Snooping and Forwarding Table will be reset to default.
  • Page 38 VID as 01, named “default”, and contains all ports as “Untagged”. Figure 19. 802.1Q Asymmetric VLAN Setting Add VID: Click to create a new VID group, assigning ports 1 ~ 28 as Untag, Tag, or Not Member. A port can be “Untagged” in only one VID.
  • Page 39 VID: A unique VLAN ID. VLAN Name: A VLAN name is used to associate with the VLAN ID. Port: The switch port number. Untag: Outgoing frames without VLAN tag. Tag: Outgoing frames with VLAN tag. Not Member: The port number which not to be grouped.
  • Page 40 IEEE 802.1Q VLAN setting. Figure 22. Modify VID PVID settings: While receiving an untagged frame from the port, the switch will assign a tag to the frame, using the PVID of the port as its VID. Figure 23. PVID Setting...
  • Page 41 Here is an example of two VLAN groups with several ports in each group and VLAN 1 (VID 01) does not have communication with VLAN 2 (VID 02). Figure 24. Step1: Set VID 01 port 1~14 to “Untag” ports and 15~28 to “Not Member” ports then apply setting. Figure 25.
  • Page 42 Step2: Create VID 02 and set port 1~14 to “Not Member” ports and 15~28 to “Untag” ports member then apply setting. Figure 26. Example2: 802.1Q Asymmetric VLAN settings example: Port 1~28 in VLAN 1, port1~5 in VLAN 2, port1,6~9 in VLAN 3.
  • Page 43 Note: The multi-need server must be support IEEE 802.1Q VLAN Step1: Enable Asymmetric VLAN function. Figure 28. Step2: Set VLAN1 port 1~28 to “Untag” ports, then apply setting. Figure 29...
  • Page 44 Step3: Create VID 02 and set port 1~5 to “Untag” ports and port 6~28 to “Not Member” ports, then apply setting. Figure 30. Step 4: Create VID 03 and set port 1, 6~9 to “Untag” ports then apply settings.
  • Page 45 Step 5: Set PVID port 2~9 value as below list Figure 32. Note: 1. Untag port VLAN member can exist in different VLAN groups simultaneously when Asymmetric VLAN function enabled. 2. You must create VLAN and add VLAN member first that just can set PVID setting.

  • Page 46: Tag Vlan Setting

    Create two VLAN groups for Tag ports multi-need server application setting and two VLAN clients cannot negotiate to each other. (Asymmetric VLAN function disabled) Figure 34. Step1: Set VLAN1 port 1 to “Tag” port, port 2~14 to “Untag” ports, and port 15~28 to...
  • Page 47 “Not Member” ports then apply setting. Figure 35.
  • Page 48 Step 2: Set VLAN1 port 1 to “Tag” port, port 15~28 to “Untag” ports, and port 2~14 to “Not Member” ports then apply setting. Figure 36. Note: The multi-need server must be support IEEE 802.1Q VLAN, the sever uplink port is port 1.

  • Page 49: Trunk Setting

    Step1: Set Switch1’s VLAN1 port 1 to “Tag” and 5~28 to “Not Member”, then apply setting. Figure 38. Step2: Set Switch2’s VLAN1 member as Switch1. Step3: Uplink two switches via Port 1. Trunk Setting The Trunking function enables the cascading of two or more ports for a combined larger bandwidth.
  • Page 50 Figure 4. Trunk Configuration Be sure that the selected trunk setting port must connect to the device with a same VLAN group.

  • Page 51: Mirror Setting

    RX (receive) mode: this mode will duplicate the data that send to the source and forward to the Sniffer port. Both (transmit and receive) mode: this mode will duplicate both the data transmit from and data that send to the source port, then it will forward to the Sniffer port.

  • Page 52: Ieee 802.1P Default Priority

    IEEE 802.1p Default Priority This feature displays the status Quality of Service priority levels of each port, and for packets that are untagged, the switch will assign the priority in the tag depending on your configuration. Figure 41. IEEE 802.1p Default Priority Setting...

  • Page 53: Broadcast Storm Control Setting

    The Broadcast Storm Control feature provides the ability to control the receive rate of broadcasted packets. If Enabled (default is Disabled), threshold settings of 8,000 ~ 4,096,000 bytes per second can be assigned. Press Apply for the settings to take effect. Figure 42. Broadcast Storm Control Setting...

  • Page 54: Advanced Setting

    SNMP Setting The Web Smart Switch supports SNMP software (referred to as an agent), which runs locally on the device. A defined set of variables (managed objects) is maintained by the SNMP agent and used to manage the device. These objects are defined in a Management Information Base (MIB), which provides a standard presentation of the information controlled by the on-board SNMP agent.
  • Page 55 Trap Name: Enter a Trap Name (i.e. Trap Name must be selected from a Community Name) IP: Enter the IP of the device to be monitored, and choose the event(s) to trap. Event: The available trap Events to choose from include: System...

  • Page 56: Spanning Tree Setting

    The Web Smart Switch supports IEEE 802.1D Spanning Tree Protocol (STP) implementation is designed to prevent network loops that could cause a broadcast storm. When the physical links forming a loop provide redundancy, only a single path will be forwarding frames.
  • Page 57 Set by the Root Bridge, this value will aid in determining that the Switch has spanning tree configuration values consistent with other devices on the bridged LAN. If the value ages out and a BPDU has still not been received from the Root Bridge, the Switch will start sending its own BPDU to all other switches for permission to become the Root Bridge.

  • Page 58: 802.1X Setting

    802.1x holds a network port disconnected until authentication is completed. Depending on the results, the port is either made available to the user, or the user is denied access to the network. 802.1X uses the Extensible Authentication Protocol (EAP) for passing authentication messages.
  • Page 59 Default is 1812. Key/Confirm Key: Masked password matching the Radius Server Key. TxPeriod: Sets the number of seconds that the switch waits for a response to an EAP-request/identity frame from the client before retransmitting the request. Default is 24 seconds.

  • Page 60: Igmp Snooping Setting

    With Internet Group Management Protocol (IGMP) snooping, the Web-Smart Switch can make intelligent multicast forwarding decisions by examining the contents of each frame’s Layer 2 MAC header. IGMP snooping can help reduce cluttered traffic on the LAN. With IGMP snooping enabled globally, the Web-Smart Switch will forward IP multicast traffic only to connections that have group members attached.
  • Page 61 Adjusting this setting effects the "leave latency", or the time between the moment the last host leaves a group and when the routing protocol is notified that there are no more members. It also allows adjustments for controlling the frequency of IGMP traffic on a subnet.
  • Page 62 Leave Timer (0-25 sec): This is the interval after which a Leave message is forwarded on a port. When a leave message from a host for a group is received, a group-specific query is sent to the port on which the leave message is received.

  • Page 63: Igmp Vlan Setting

    To enable IGMP snooping for a given VLAN, select Enable under State then press the Edit button under Static Router Port Setting, then select the ports to be assigned for IGMP snooping for the VLAN, and press Apply for changes to take effect.
  • Page 64 To view the Multicast Entry Table for a given VLAN, press the View button. Figure 11. IGMP – Multicast Entry Table Setting...

  • Page 65: System Setting

    System Setting Find that there are nine items, including System Information, System Setting, Trap Setting, Password Setting, Statistics, Factory Reset, Backup Setting, Firmware Upload and System Reboot in System menu. System Information Press on “System Information” to display the system information...

  • Page 66: System Setting

    When using static mode, the IP Address, Subnet Mask and Gateway can be manually configured. When using DHCP mode, the Switch will first look for a DHCP server to provide it with an IP address, network mask, and default gateway before using the default or previously entered settings.

  • Page 67: Trap Setting

    By configuring the Trap Setting, it allows the Web Management Utility to monitor specified events on the Web-Smart Switch. By default, Trap Setting is Disabled. When the Trap Setting is Enabled, enter the Destination IP address of the managing PC that will receive trap information. Figure 14. Trap Setting System Events: Monitoring the system’s trap.

  • Page 68: Password Setting

    Web Smart Switch. After entering the old password and the new password two times, press Apply for the changes to take effect. If you forget the password, you can press the “Reset” button in the rear panel of the Switch.

  • Page 69: Statistic

    Statistic The Statistic Menu screen will display the status of each port packet count. Figure 16. Statistics Refresh: To renew the details collected and displayed. Clear Counter: To reset the details displayed.
  • Page 70 To view the statistics of individual ports, click on it’s Port ID. Figure 17. Port Statistics...

  • Page 71: Factory Reset

    Factory Reset The Factory Reset helps you to reset the device back to the default setting from the factory. All of the configuration will be reset, the IP address of the device will be set to default setting 192.168.0.1. Figure 18. Factory Reset...

  • Page 72: Firmware Upload

    Figure 20. Firmware Upload System Reboot Provides a safe way to reboot the system and ensures the configuration has been saved, or all the changes you just made may be lost after system reboot. Figure 21. System Reboot...

  • Page 73: Logout

    Logout When pressed you will logout of the web configuration page and return back to the first Login page. Figure 22.

  • Page 74: Technical Specifications

    IEEE 802.3u 100BASE‐TX Fast Ethernet  IEEE 802.3ab 1000BASE‐T Gigabit Ethernet  IEEE 802.3z 1000BASE‐SX/LX Gigabit Ethernet  Protocol  CSMA/CD  Data Transfer  Ethernet: 10Mbps (half‐duplex), 20Mbps (full‐duplex)  Rate  Fast Ethernet: 100Mbps (half‐duplex), 200Mbps (full‐duplex)  Gigabit Ethernet: 2000Mbps (full‐duplex)  Topology  Star  Network Cables  10BASET: 2‐pair UTP Cat. 3, 4, 5; up to 100m  100BASE‐TX: 2‐pair UTP Cat. 5; up to 100m  1000BASE‐T: 4‐pair UTP Cat. 5; up to 100m  Fiber module: mini‐GBIC Fiber module  Number of Ports  24 x 10/100M Auto‐MDIX Fast Ethernet ports  4 x 10/100/1000M Auto‐MDIX Gigabit ports  2 x Mini‐GBIC slots (share with port 25~26)  Physical and Environmental  AC inputs  100‐240V AC, 50‐60 Hz internal universal power supply  Power  19 watts (max)  Consumption      o Temperature  Operating: 0~ 40  C, Storage: ‐10 ~ 70 C  Humidity  Operating: 10% ~ 90%, Storage: 5% ~ 90%  Dimensions  440 x 140 x 44 mm (W x H x D)  Certifications  FCC, CE ...
  • Page 75 Performance  Transmits  Store‐and‐forward  Method:  RAM Buffer:  128KBytes per device  Filtering Address  8K entries per device  Table:  MAC Address  Automatic update  Learning:  Packet Filtering /  10Mbps Ethernet: 14,880/pps  Forwarding Rate:  100Mbps Fast Ethernet: 148,800/pps  1000Mbps Gigabit Ethernet: 1,488,000/pps ...

  • Page 76: Limited Warranty

    There are no user serviceable parts inside the product. Do not remove or attempt to service the product through any unauthorized service center. This warranty is voided if (i) the product has been modified or repaired by any unauthorized service center, (ii) the product was subject to accident, abuse, or improper use (iii) the product was subject to conditions more severe than those specified in the manual.
  • Page 77 DISCLAIMER OF LIABILITY FOR DAMAGES WILL NOT BE AFFECTED IF ANY REMEDY PROVIDED HEREIN SHALL FAIL OF ITS ESSENTIAL PURPOSE. Governing Law: This Limited Warranty shall be governed by the laws of the state of California. Note: AC/DC Power Adapter, Cooling Fan, Cables and Power Supply carry 1-...

Table of Contents