Logging into the FTP server 3.4.3. Common FTP commands GPL Statement 4.1. GNU General Public License 4.1.1. Preamble 4.1.2. GNU General Public License – Terms and Conditions or Copying, Distribution and Modification 4.1.3. NO WARRANTY Appendix Product Warranty Information - 2 -...
Initial Operation Connect your computer to the router with an Ethernet LAN cable and power the router on. It will take about 30 seconds to boot. You can then access it via telnet or web browser at the IP address 192.168.11.1.
- Safari 2.x and newer versions 2.1. Preparation Connect your PC to the router and power the router on as described in 1.2.2. After the router has loaded its operating system, you can communicate with it via your LAN network interface.
PPPoE, PPTP, L2TP, static IP, or HeartBeat Signal. If you don’t use a password to log in to your ISP, you may need to enter “0000” for the password. Also, for some ISPs you should not enter the service name, as it will prevent establishing the connection.
DynSIP.org Custom Individual DynDNS service configuration 126.96.36.199. MAC Address Cloning MAC address cloning lets you assign a different MAC address to the router than the one encoded in the hardware. 188.8.131.52. Advanced Routing Operating Mode The default operating mode of the router is Gateway. Other routing protocols are available.
Besides the default DHCP server, you can define additional DHCP servers. 184.108.40.206. EoIP Tunnel EoIP (Ethernet over IP) tunnels can transport Ethernet data packages via a tunnel over existing IP connections. You can define up to 10 tunnels that can also be bonded. 2.3.2. Wireless 220.127.116.11.
Channel Width Some wireless network modes support wireless channel widths besides the standard 20 MHz. 802.11g & 802.11n offer the option to use 40 MHz channels for enhanced throughput. Both the AP and the client must support 40 MHz channels to use them.
With WPA or WPA2 encryption, there are several encryption algorithms to choose from. AES is more secure but TKIP is more widely supported. There is also a TKIP + AES setting, but that does not offer more security than TKIP.
Enables the AOSS Service. When disabled, AOSS cannot be used. Start AOSS Negotiation To initiate AOSS, either click the AOSS button in the GUI or hold down the AOSS button on the front of the router for 3 seconds. Security Modes You may choose which security modes are offered in the AOSS negotiation process.
18.104.22.168. MAC Filter The MAC Filter defines a list of client MAC addresses that are allowed to connect wirelessly. MAC addresses that aren’t on the list aren’t allowed to connect. 2.3.3. Services 22.214.171.124. Services The services section allows the configuration of basic service settings.
The router can also be configured as VPN server or VPN client. PPTP When defining the PPTP server’s IP range, avoid overlap with the range of IP addresses handed out by DHCP if DHCP is enabled. The IP range is defined using the following syntax: xxx.xxx.xxx.<start-ip>-<end-ip>...
Sputnik for usage. 126.96.36.199. Milkfish SIP Router This package is an implementation of the Milkfish SIP router. 188.8.131.52. My Ad Network Allows the creation of an AnchorFree Hotspot that can be used to create revenue via AnchorFree. 2.3.4. Security 184.108.40.206. Firewall...
220.127.116.11. Port Range Forwarding Port range forwarding works similarly to port forwarding. Unlike port forwarding, instead of a single port, a range of ports is forwarded to the same range of ports at the internal target IP address. 18.104.22.168. Port Triggering...
You can use this feature to store your current configuration into a backup file, or to restore from a previously stored configuration. This also makes it simple to set up a number of routers with the exact same configuration. 2.3.8.
22.214.171.124. If the WAN interface is enabled, this screen displays WAN settings and throughput statistics. 126.96.36.199. Here you can find LAN-related information like active clients and DHCP clients. 188.8.131.52. Wireless The wireless LAN status screen displays the current wireless LAN interface configuration, wireless LAN clients (in AP modes), and access points (in client modes).
Enter your country in “Regulatory Domain” In the “Antenna Gain“ field, please enter the gain of the antenna on your router. The firmware will adjust the transmit power accordingly to meet regulatory requirements. Please keep in mind that very long cables can dampen the HF signal thus reducing the usable antenna gain.
IP addresses from the server. 3.2. Wireless Client The router can be also used as a wireless LAN client. This can be useful if you want to connect devices to your wireless LAN that do not have a wireless LAN interface.
Configure “Wireless Network Mode” to match the capabilities of the access point you want to connect to. Enter the network name (SSID) of the AP you want to connect to into “Wireless Network Name (SSID)”. Click “Save“.
Configure “Wireless Mode” to “Client Bridge”. Set “Wireless Network Mode” to match the access point you want to connect to. Enter the network name (SSID) of the AP you want to connect to. Click “Save”. Wireless -> Wireless Security ...
DHCP should receive an IP address. 3.4. FTP Server The router can be used as an FTP server when a USB disk (such as a hard disk or flash memory device) is connected to the USB port on the rear of the router.
･Connect a USB disk to the router. After a short wait, the disk information is displayed in the Disk Info section. Services -> NAS ･Make the settings in the ProFTPD section, and click [Apply Settings]. Setting example: ProFTPD Enable Server Port...
･Enter “ftp 192.168.11.1” to access the FTP server. ･Enter the user name, and press the Enter key. ･Enter the password, and press the Enter key. ･When the login is successful, “ftp>” appears on the screen. ･To logout, enter the “bye” command. 3.4.3.
Deletes a file on delete the remote computer test1.jpg mdelete Deletes multiple mdelete files on the remote test1.jpg computer test2.jpg test3.jpg rename Renames a file on rename the remote computer test1.jpg new1.jpg help Displays the Help help for FTP commands...
GNU Public Licence (GPL)/the GNU Lesser Public Licence (LGPL). To the extent that it is applicable within the context of the GPL and the LGPL, the conditions of the GPL and the LGPL, as well as the relevant source codes, are available from the manufacturer. The code underlying the GPL/LGPL for the software shall be provided, without any ensuing warranty or liability claims.
Program. In addition, mere aggregation of another work not based on the Program with the Program (or with a work based on the Program) on a volume of a storage or distribution medium does not bring the other work under the scope of this License.
The source code for a work means the preferred form of the work for making modifications to it. For an executable work, complete source code means all the source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the executable.
SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION. 12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY...
Under no circumstances shall Buffalo Technology/(Buffalo Inc.) be liable in any way to the user for damages, including any lost profits, lost savings or other incidental or consequential damages arising out of the use of, or inability to use the Buffalo products.
Packet Info ..................92 Client Monitor ................. 93 Ping ....................94 Chapter 5 - Connect to a Wireless Network ....95 Automatic Secure Setup (AOSS/WPS) ........95 Windows 7/Vista (Client Manager V) ..........96 Windows XP (Client Manager 3) ............ 97 Mac OS X (AOSS Assistant) ............
Cannot access the web-based configuration Interface... 105 Cannot connect to the network wirelessly....... 106 You forgot AirStation's SSID, Encryption Key, or Password..106 The link speed is slower than 300 Mbps (Maximum link speed is only 130 Mbps)................ 106 Other Tips ................107 Appendix A - Specifications ..........
Chapter 1 - Product Overview Installing Your AirStation To install your AirStation, insert the software CD from your package into your computer and follow the directions on the screen. For more infomation about installation, turn to chapter 3 of this manual.
MovieEngine uses QoS to optimise your network for multimedia streaming. This can reduce jumps, distorted audio, and dropped frames while watching streamed video. NAS (Network Attached Storage) Attach a USB hard drive to the AirStation and share it on the network as a NAS. All connected clients can access it. Gigabit Ethernet This unit supports gigabit Ethernet, allowing transmission rates of up to a billion bits per second.
However, the automatic installation program on the CD requires a connected Windows 7, Vista or XP computer to run. If you use the AirStation with a different operating system, you will have to configure your network settings manually from a browser window.
Hardware Overview Front Panel LEDs AOSS Button To initiate AOSS, hold down this button until the 2.4 GHz LED and 5 GHz LED flash (about 1 second). Then, push or click the AOSS button on your wireless client device to complete the connection.
Initializing settings Initializing the settings. Unplug the AC adapter from the wall socket, wait for a few seconds, and then plug it again. If the light still flashes, please contact technical support. Never unplug the AC adapter while the Diag LED is blinking continuously.
Internet port. The default setting for this switch is Auto. USB Eject Button To dismount a USB hard drive, hold down this button until the USB LED flashes (about 3 seconds). The USB drive can then be unplugged safely.
The Internet port is transmitting data. DC Connector Connect the included AC adapter here. Bottom Reset Button To reset all settings, hold down this button until the Diag LED comes on (about 3 seconds). Power must be on. WZR-HP-AG300H User Manual...
Factory Default Settings This sticker shows the AirStation’s SSID, default encryption key, and WPS PIN code. By default, encryption is disabled for AirStations sold in Asia Pacific. WZR-HP-AG300H User Manual...
Chapter 2 - Placing Your AirStation Vertical Placement If the AirStation is to be placed vertically, attach the stand as shown. Horizontal Placement When installing the AirStation horizontally, attach the stand for best heat dissipation. Attach the stand as shown in the figure.
Chapter 2 Placing Your AirStation Install horizontally. Wall-Mounting To wall-mount the AirStation, attach FRONT the stand to the wall with the two screws (included). 8.6 cm (~3.4 inches) Snap the center of the AirStation to the stand as shown. WZR-HP-AG300H User Manual...
If your computer uses a different operating system, use manual setup instead. Note: · To use a wireless client in Windows 7 or Vista, perform setup using the AirNavigator CD to automatically generate a profile for wirelessly connecting to the AirStation. After setup is complete, once the LAN cable is removed, you can connect from your wireless client to the AirStation.
Chapter 3 Installation Plug one end of the LAN cable into your modem and the other end to the AirStation’s Internet (WAN) port. Turn on the modem. modem ROUTER AUTO LAN cable EJECT 1) connect Internet port 2) connect INTERNET...
Launch a web browser. If the home screen is displayed, setup is complete. If username and password fields are displayed, enter “root” for the user name. Enter “admin” for the password if you’re using the professional firmware (default), or leave the password field blank if you’ve switched to the user-friendly firmware.
Windows Insert the AirNavigator CD into your computer. The setup wizard will automatically launch. Note: If the Setup Wizard does not launch, open the CD and double-click [ASSetWiz.exe] in the “Win” folder. Click [Change Firmware]. The procedure for wiring will be displayed.
When this screen is displayed, click [Change Firmware]. If requested, enter the AirStation’s username and password. Note: By default, the professional firmware doesn’t have a username and a password configured. Set them before you go to the next step. WZR-HP-AG300H User Manual...
[Upgrade] or [Apply], and follow the instructions on the screen. Note: If the firmware name is not displayed on the screen, click [Browse...] and select the desired firmware. The firmware files are contained in the “Firmware” folder of the AirNavigator CD.
To replace the professional firmware with the user-friendly firmware, click [Administration] > [Firmware Upgrade]. To replace the user-friendly firmware with the professional firmware, go to [Easy Setup] and click [Update AirStation Firmware]. Click [Browse...] to select the firmware file, and click [Upgrade] or [Apply].
Chapter 3 Installation User-friendly firmware update screen: About this User Manual This user manual is primarily for AirStations with the user-friendly firmware. For more information on the professional firmware (dd-wrt), refer to www.dd-wrt.com/wiki. WZR-HP-AG300H User Manual...
In router mode: 192.168.11.1 In bridge mode: 192.168.11.100 Note: If the router switch is set to auto and the unit is in bridge mode, then the AirStation’s IP address was assigned by an external DHCP server. · If you changed the IP address of the AirStation, then use the new IP address.
Note : This example, like others in this manual, shows the user-friendly firmware. The dd-wrt based professional firmware is somewhat different. For more information on the professional firmware, visit dd-wrt’s website at www.dd-wrt.com.
Chapter 4 Configuration Configuration Interface Menus in Router Mode The menu structure for the AirStation in router mode is as follows. Please refer to the pages listed at right for explanations of each item. Main screen Descriptions Page Internet/LAN Internet Configure Internet side port and settings.
Page 76 Admin Config Name Configure the AirStation’s name. Page 78 Password Configure the AirStation’s login password for access to the configuration Page 79 interface. Time/Date Configure the AirStation’s internal clock. Page 80 Configure the AirStation to synchronize with an NTP server to Page 81 automatically set the AirStation’s internal clock.
Chapter 4 Configuration Configuration Interface Menus in Bridge Mode The menu structure in bridge mode is as follows. Please refer to the pages listed at right for explanations of each item. Main screen Descriptions Page LAN Config Configure LAN side ports and devices.
Access Configure access restrictions to the AirStation’s configuration interface. Page 84 Check the AirStation’s logs. Page 85 Save/Restore Save or restore the AirStation’s configuration from a configuration file. Page 86 Initialize/Restart Initialize the AirStation or reboot it. Page 87 Update Update the AirStation’s firmware.
Chapter 4 Configuration Setup Setup is the home page of the configuration interface. You can verify settings and the status of the AirStation here. Parameter Meaning Internet/LAN (LAN Config) Displays the configuration screen for the Internet port and LAN ports.
This indicates the operation mode of the AirStation. Internet Information Displays WAN-side system information for the AirStation. Check Connection Click this button to check if the AirStation is connected to the Internet properly. Refresh Click this button to refresh the current screen.
Note: Configuring an improper MAC address may make the AirStation unusable. Change this setting at your own risk. MTU size of Internet Port Configure the MTU value of the Internet port. Values of 578 to 1500 bytes may be entered. WZR-HP-AG300H User Manual...
If you have registered multiple connection destinations in the PPPoE Connection List, connection destinations selected here have priority. You need to configure the route to which PPPoE is connected to if you don’t use the default settings. IP Unnumbered PPPoE Connection Select the destination from the PPPoE Connection List which is used when “Use IP Unnumbered”...
Enter the password specified by your ISP for PPPoE certification. You may enter up to 32 alphanumerical characters and symbols. Service Name Fill in this field only if your ISP specifies a Service Name. Leave blank otherwise. You may enter up to 32 alphanumerical characters and symbols.
Keep Alive PPPoE Connection No. *-Add If Keep Alive is enabled, then the AirStation will issue an LCP echo request once a minute in order to maintain the connection with the PPPoE. If the server does not respond for more than 6 minutes, the line is recognized as disconnected and the AirStation will terminate the connection.
Chapter 4 Configuration DDNS (Router Mode only) Configure Dynamic DNS settings. Many settings are only available when the appropriate Dynamic DNS service is enabled. Parameter Meaning Dynamic DNS Service Select a provider (DynDNS or TZO) for Dynamic DNS. Username Enter the Dynamic DNS username. You may enter up to 64 alphanumerical characters and symbols.
Specifies the period to notify the dynamic DNS service provider of the current IP address. For DynDNS, set it between 0 and 35 days. For TZO, set it between 0 and 99 days. If 0 (zero) days is set, no periodic update is performed.
Enter the password to connect to the PPTP server. You may enter up to 16 alphanumerical characters and symbols. Method of Acquiring IP Address Select the method to be used to assign the IP address is assigned to the PPTP client. PPTP User List Displays the PPTP connection user information.
LAN Side IP Address Set an IP unnumbered LAN side IP address. (For IP Unnumbered) Note: A PC with a normal LAN side IP address and a PC with an IP Unnumbered IP address cannot communicate each other. Advanced Settings Check [Display] to display DHCP server advanced settings options.
Chapter 4 Configuration Parameter Meaning DNS Servers Set the DNS server IP address for the DHCP server to issue to * Router Mode only clients. WINS Server Set the WINS server IP address for the DHCP server to issue to * Router Mode only clients.
Meaning IP Address Enter an IP address to lease manually. The IP address should be from the same subnet as the DHCP scope, but not be within the range that DHCP is assigning to other devices. MAC Address Enter the MAC address which identifies the client.
Chapter 4 Configuration NAT (Router Mode only) Configure network address translation settings. This enables LAN-side devices to communicate with the Internet. Parameter Meaning Address Translation Enable to use Network Address Translation. Log Output of Deleted Packets Enable to log deleted packets (such as errors) during address translation.
Adds a gateway address to a routing table. Metric The metric is the maximum number of router hops a packet may take on the way to its destination address. Values between 1 and 15 may be entered. The default value is 15. Routing Information Manual entries will appear here after being added.
Note: Configure requests will not be accepted if AOSS is in use. AirStation PIN Displays the PIN code of the AirStation. Clicking [Generate PIN] will generate a new PIN code. This code can be entered into other wireless devices that support WPS. Enrollee PIN Enter the PIN code for the other wireless device and click [OK].
Click this button to disconnect AOSS connections. Note: If AOSS connections are disconnected, the SSID and encryption keys will be restored to their last settings from before AOSS was used. Encryption Type of Exclusive SSID for You may allow a separate SSID specifically for WEP connections. If “disabled”...
300 Mbps mode uses twice the normal frequency range, 40 MHz instead of 20 MHz. In uncongested areas this can increase performance. To use 300 Mbps mode, set the Bandwidth to 40 MHz and choose an Extension Channel. Note: If Auto Channel is selected, then the Extension Channel is set automatically.
SSIDs, each with different wireless security settings. Clicking [Use Single SSID] will disable Multi Security. The AirStation will then allow one SSID and one type of wireless security. Note: When using Multi Security, enable at least one of the following: SSID1, SSID2, or SSID3.
There are two different formats for a pre-shared key. Use 8 to 63 alphanumeric characters (case-sensitive) for an ASCII passphrase, or use 64 alphanumeric characters (0 to 9 and a to f, not case- sensitive) for a hexadecimal passphrase. WZR-HP-AG300H User Manual...
A WEP encryption key (passphrase) may have any of four different formats. An ASCII passphrase may use either 5 or 13 alphanumeric characters (case-sensitive). A hexadecimal passphrase may use either 10 or 26 alphanumeric characters (0 to 9 and a to f, not case-sensitive). Advanced Configure advanced wireless settings. Parameter...
Adds a wireless device to the list of permitted devices. MAC Addresses to be Registered Enter a MAC address of a wireless device to permit to connect to the AirStation. Click [Register] to add that MAC address to the list.
IGMP and restricts unnecessary multicast transfers to wired or wireless ports. Multicast Aging Time Set the time to hold the data from multicast snooping in the range of 1 to 3600 (seconds). Enter a value bigger than the IGMP/MLD query interval.
Prohibit NBT and Microsoft-DS Routing Enabling this blocks communication using these protocols from the WAN side to the LAN side or from the LAN side to the Internet. You can configure this with PPPoE if you select [Use PPPoE Client] or [Use IP Unnumbered] in Method of Acquiring IP address (page 32), or if Easy Setup identified a PPPoE connection during setup.
Block Ping from Internet If this is enabled, the AirStation will not respond to pings from the Internet side. You can configure this with PPPoE if you select [Use PPPoE Client] or [Use IP Unnumbered] in Method of Acquiring IP address (page 32), or if Easy Setup identified a PPPoE connection during setup.
Specify how to process target packets. Direction Specify the transmission direction of target packets. IP Address Specify the sender's IP address and receiver's IP address of the target packets. Protocol Select a protocol for target transmission packet. IP Filter Information Display the list of IP filters which have been registered.
Enable to use IPv6 Passthrough for address translation. PPPoE Passthrough Enable to use PPPoE bridging. PPPoE bridging lets you automatically obtain an IP address from your provider for your LAN- side computer using the PPPoE protocol because PPPoE packets can pass between the Internet and LAN.
Specify a group name for a new rule to belong to. Select [New Group] and enter the new group name in the Group Name field to create a new group. A group name can include up to 16 alphanumeric characters.
Port Forwarding Registration Shows current entries in the port translation table. Information DMZ (Router Mode only) Configure a destination to transfer communication packets without a LAN side destination to. Parameter Meaning IP Address of DMZ Enter the IP address of the destination to which packets which are not routed by a port translation table are forwarded.
Chapter 4 Configuration UPnP (Router Mode only) Configure UPnP (Universal Plug and Play). Parameter Meaning UPnP Enable or disable Universal Plug and Play (UPnP) functionality. WZR-HP-AG300H User Manual...
("'), quotation marks (“), and semicolons (;). protocol Select either TCP or UDP. destination Port Specify a destination port from 1 - 65535. If this field is empty, a random port is selected. WZR-HP-AG300H User Manual...
Chapter 4 Configuration Parameter Meaning priority Select high, medium or low. If packets do not qualify for classification as a type on the list, then their priority is treated as a level between medium and low. WZR-HP-AG300H User Manual...
Select the Multicast Control rate. Multicast Control Turn on Multicast Control. TCP Rwin Size Limit Limits the maximum size of TCP Rwin packets passing through the AirStation’s wireless LAN. Wireless Priority Control Rules Display the list of rules controlling the priority of packets passing through the AirStation’s wireless LAN.
Displays information for attached USB disks. Disks are removed when [Remove] in the Device column is clicked. Disk Assignment A disk number will be automatically assigned to the disk or you can choose a number. Select a disk number, or select [Do not assign], then click [Apply].
Automatic USB Disk Assignment Check [Use] to automatically select an attached USB hard disk. The entire drive will be used as the shared folder. To configure your disk and share manually, uncheck [Use]. [Use] is selected by default. FAT format file name character code Select the character code for filenames in FAT formatted partitions.
Enter a description of the shared folder (optional). Up to 75 alphanumeric characters, spaces, hyphens (-), and underscores (_) may be used. Disk Partition Area* Displays the partition area, format type, and the capacity of the USB disk. Disclosed to* Check the functionality that you want to support. Win/Mac OS (Samba NAS), Web Access, Media Server, and/or BitTorrent may be checked.
Displays information about the shared folder. Information* * This is not displayed when Automatic USB Disk Assignment (page 68) is used: The following shared folder settings are used when Disk Management is activated: • All folders: Access limits in effect.
Chapter 4 Configuration User Management This screen lets you add users to the access list with the ability to access shared folders. Parameter Meaning Username Enter the name of a user to be given access to the shared folder. Up to 20 alphanumeric characters, space, hyphens (-), and underscores (_) may be used for each user.
Rename your AirStation if desired. Up to 15 alphanumeric characters, space, and hyphens (-), may be used. The AirStation name is also used as the hostname that will be used with the shared service. The shared service may not be available you use over 15 alphanumeric characters in your AirStation’s name.
[BuffaloNAS.com name] and [BuffaloNAS.com key] to use BuffaloNAS.com. 3 - 0 alphanumeric characters, spaces, hyphens (-), underscores (_) and period (.), may be used in the BuffaloNAS. com name. 3 - 20 alphanumeric characters, spaces, hyphens (-), underscores (_) and period (.), may be used in the BuffaloNAS.com key.
Chapter 4 Configuration Parameter Meaning Web Access Displays the status of web access. External Port Status Displays the status of the external port. BuffaloNAS.com Displays the status of BuffaloNAS.com. WZR-HP-AG300H User Manual...
Parameter Meaning BitTorrent Function Enable to use the BitTorrent client. If the BitTorrent client is enabled, overall communication performance may decrease and settings screens may respond slower. If that happens, reformat the USB disk with XFS. That may help performance.
Displays the BitTorrent download manager screen. Add a torrent, then click [Add] to download the file(s). [Delete BitTorrent information] Deletes all files, including the torrent files and files which are currently downloading. Downloaded files are not deleted. BitTorrent Status Displays the status of the BitTorrent client.
Configure basic AirStation settings. Parameter Meaning AirStation Name Enter a name for the AirStation. Names may include up to 64 alphanumeric characters and hyphens (-). List Network Services Enable or disable this to display the computers and devices on your network with their supported services.
Chapter 4 Configuration Password Configure the password to log in to the AirStation’s configuration screen. Parameter Meaning Administrator Name The name of the Administrator account is “root”. Administrator Password The Administrator password may contain up to 8 alphanumeric characters and underscores (_).
Configure the AirStation’s internal clock. Parameter Meaning Local Date You may manually set the date of the AirStation’s internal clock. Local Time You may manually set the time of the AirStation’s internal clock. Time Zone Specify the time zone (offset of Greenwich Mean Time) of the AirStation's internal clock.
(-), and underscores (_) may be used. The default is [time. nist.gov]. Update Interval How often will the AirStation check the NTP server for the correct time? Intervals of 1 - 24 hours may be set. The default is 24 hours. WZR-HP-AG300H User Manual...
Chapter 4 Configuration Parameter Meaning Schedule feature Enable to schedule Eco Mode. If Eco mode is enabled, AOSS will function only when the AirStation is in Normal operating mode. Weekly schedule Graphically displays the configured schedule. Register schedule Configure operational mode for time periods in the weekly schedule.
WAN (Internet) side. Permitted IP address Displayed only if Internet side configuration is enabled. Enter the IP address of a device that is permitted to configure the AirStation remotely from the WAN (Internet) side. Permitted Port Displayed only if Internet side configuration is enabled. Set a port number (1 - 65535) to configure the AirStation from the WAN (Internet) side.
Enable to send logs to a syslog server. Syslog Server Identify the syslog server by hostname, hostname with domain name, or IP address. You may enter up to 255 alphanumeric characters, hyphens (-), and underscores (_). Transfer Logs Choose which logs will be transferred to the syslog server.
Save current settings Clicking [Save] will save the current configuration of the AirStation to a file. If the [Encrypt the configuration file with a password] option is checked, then the configuration file will be password protected with the current administrator password.
Chapter 4 Configuration Initialize/Restart Initialize or restart the AirStation. Parameter Meaning Restart Click [Restart Now] to restart the AirStation. Initialize Click [Initialize Now] to initialize and restart the AirStation. WZR-HP-AG300H User Manual...
Firmware File Name Click [Browse...] to navigate to the firmware file on your computer if [Specify Local File] was selected. You don’t need to specify the firmware location if you’re using [Automatic Update]. Click [Update Firmware] to update the firmware.
Chapter 4 Configuration Parameter Meaning Model Displays the product name of the AirStation and the firmware version. AirStation Name Displays the name of the AirStation. Mode Switch Status Displays the status of the AirStation’s mode switch. Operational Mode Displays the AirStation’s current operational mode.
Chapter 4 Configuration Logs The AirStation’s logs are recorded here. Parameter Meaning Display log info Choose the types of logs to display. Logs Displays the log information recorded in the AirStation. WZR-HP-AG300H User Manual...
Packet Info Viewpacket transfer information. Parameter Meaning Sent Displays the number of packets sent to the WAN, the LAN, and the wireless LAN. Received Displays the number of packets received from the WAN, the LAN, and the wireless LAN. WZR-HP-AG300H User Manual...
Chapter 4 Configuration Client Monitor This screen shows devices that are connected to the AirStation. Parameter Meaning Client Monitor Displays information (MAC address, lease IP address, hostname, communication method, wireless authentication and 802.11n) for devices that are connected to the AirStation.
Chapter 4 Configuration Ping A ping test checks whether the AirStation can communicate with a specific network device. Parameter Meaning Destination Address Enter the IP address or hostname of the device that you are testing communication with, then click [Execute]. The result will be displayed below.
Game console (AOSS Devices) • Before using AOSS/WPS to connect to a Buffalo wireless client, install Client Manager software from the included AirNavigator CD. Consult your wireless client’s documentation for more information. • Buffalo’s Client Manager software can be used with the wireless LAN devices built into most computers.
If the User Account Control screen opens, click [Yes] or [Continue]. Click the [WPS AOSS ] button. Follow any instructions displayed on the screen. When the 2.4 GHz and 5 GHz LEDs on the front of the AirStation stop fl ashing and is lit steadily, the connection is complete.
Click the [WPS AOSS] button. It will take several seconds for your wireless connection to be confi gured. When the 2.4 GHz and 5 GHz LEDs on the front of the AirStation stop fl ashing and glow steadily, the connection is complete.
Chapter 5 Connect to a Wireless Network Mac OS X (AOSS Assistant) If you are using Mac OS X 10.6 / 10.5 / 10.4, use the included AOSS Assistant software to connect wirelessly with AOSS. Load the AirNavigator CD in your Macintosh.
If you are using a game machine which supports AOSS or WPS, refer to that device’s manual to initiate AOSS/WPS. When instructed, hold down the AOSS button on the AirStation for 1 second. When the 2.4 GHz and 5 GHz LEDs on the front of the AirStation stop flashing and glow steadily, the connection is complete.
Chapter 5 Connect to a Wireless Network Enter the encryption key and click [OK]. Windows Vista (WLAN AutoConfig) With Vista, use WLAN AutoConfig to connect to the AirStation. Right click on the wireless network icon in the system tray. Click [Connect to a network].
Chapter 5 Connect to a Wireless Network Enter the encryption key and click [Connect]. Step through the wizard to finish configuration. If the Set Network Location screen is displayed, select [Home], [Work], or [Public location] depending on where you’re using the AirStation. WZR-HP-AG300H User Manual...
Windows XP includes Wireless Zero Config, a built-in utility to connect to your AirStation. Note: If Client Manager 3 is installed on your computer, Wireless Zero Config is disabled. Uninstall Client Manager 3 to use Wireless Zero Config, or just use Client Manager 3 to connect to the AirStation. Right click on the wireless network icon in the system tray.
Mac OS X (AirPort) Use AirPort on a Mac to connect to the AirStation. Refer to the label on the side of the AirStation. Make a note of the SSID and KEY printed on the label. Click the icon in the top section of the screen and select [Turn Airport On].
Green light is ON or flashing Internet Green light is ON or flashing • Make sure that your computer is set to [obtain an IP address automatically]. (See appendix D) • Restart your AirStation. Cannot access the web-based configuration Interface.
You forgot AirStation's SSID, Encryption Key, or Password. Hold down the reset button on the base of your AirStation for 3 seconds to initialize its settings. All settings, including your password, SSID, and encryption key will be initialized to their defaults. The...
Find the settings area for SSID. Select the [Use] radio button and enter the name you wish to use for your network in the text field provided. Click [Apply] to save the settings. Once the wireless router has rebooted, select the new network name for all wireless devices and re-enter your encryption key if necessary.
1 - 11 may be selected. Try the Auto-Channel option if available. Otherwise, manually select an alternate channel and click [Apply]. Issue: Though I am able to successfully make a connection with my wireless router, I am unable to access the Internet with my web browser. Answer: First, power off the Cable or DSL modem, the wireless router, and your computer.
IEEE802.11a / IEEE802.11b / IEEE802.11g / IEEE802.11n Transmission Method Direct Sequence Spread Spectrum (DSSS), OFDM, MIMO 802.11a Frequency Range Available 808.11a frequencies depend on the country of purchase. See the next page for details. 802.11g Frequency Range 2,412 - 2,462 MHz (Channels 1 - 11) Transmission Rate 802.11b:...
External AC 100-240 V Universal, 50/60 Hz Power Consumption About 13.2 W (Max) Dimensions 165 mm x 158 mm x 35mm (6.5 x 6.2 x 1.3 in.) Weight 330 g (11.6 oz.) (not including the stand) Operating Environment 0 - 40° C (32 - 104° F), 20 - 80% (non-condensing) 802.11a Frequency Range...
Appendix B - Default Configuration Settings Feature Parameter Default Setting Internet Method of Acquiring IP Address Perform Easy Setup (Internet Connection Wizard) (Router Mode only) Default Gateway none Address of DNS Name Server none Internet MAC Address Use Default MAC Address...
Bridge Mode (Router Switch AUTO): Obtain automatically from DHCP Server DHCP Server Function Enabled (Router Mode only) DHCP IP Address Pool 192.168.11.2 for up to 64 Addresses (Router Mode only) LAN Side IP Address none (For IP Unnumbered) (Router Mode only)
Wireless encryption TKIP/AES mixedmode, or no encryption WPA-PSK (Pre-Shared Key) A 13-digit random value or disabled (Printed on the label of the AirStation. Encryption is disabled in default settings on AirStation for Asia Pacific.) Rekey interval 60 minutes WZR-HP-AG300H User Manual...
Appendix B Default Configuration Settings Feature Parameter Default Setting IP Filter Log Output Disabled (Router Mode only) IP Filter Information none VPN Pass IPv6 Pass Through Disabled Through PPPoE Pass Through Disabled (Router Mode only) PPTP Pass Through Enabled Port Forwarding...
2010 Year 1 Month 1 Day Local Time 0 Hour 0 Minute 0 Seconds Time Zone (GMT+00:00) Greenwich Mean Time,London DST (Daylight Saving Time) EU type 1 For GMT+00:00(From Last Sunday in Mar to last Sunday in Oct) NTP Functionality Enabled NTP Server time.nist.gov...
Windows 7/Vista Note: · If Client Manager V is not already installed, install it from the AirNavigator CD. Click [Install Wireless Client Driver and Application] > [Options] > [Advanced Installation], and install Client Manager V.
The 11a display shows usage in the W52, W53, and W56 channels. Colors are used to indicate the signal strength of the access point. Colors closer to red indicate an access point with a stronger signal strength, and colors closer to blue indicate an access point with a weaker signal strength.
Appendix C Checking the Wireless Signal Quality and Strength The software license screen is displayed when starting for the first time only. Click [Agree] to proceed. Parameter Meaning Network name (SSID) This displays the SSID of the AirStation that is currently connected.
If the User Account Control screen opens, click [Yes] or [Continue]. Select [Internet Protocol Version 4 (TCP/IPv4)] then click [Properties]. To have DHCP set your IP address settings automatically, check [Obtain an IP address automatically] and [Obtain DNS server address automatically].
If the User Account Control screen opens, click [Yes] or [Continue]. Select [Internet Protocol Version 4 (TCP/IPv4)], then click [Properties]. To have DHCP set your IP address settings automatically, check [Obtain an IP address automatically] and [Obtain DNS server address automatically].
Right click on [Local Area Connection], then click [Properties]. Select [Internet Protocol (TCP/IP)], then click [Properties]. To have DHCP set your IP address settings automatically, check [Obtain an IP address automatically] and [Obtain DNS server address automatically]. To set your IP address settings manually, enter values for each setting. Examples: If the router’s IP address is 192.168.11.1,...
Click [Apple menu] > [System Preferences…]. Click [Network]. Click [Ethernet]. To have DHCP set your IP address settings automatically, select [Using DHCP] in the Configure IPv4 field. To set your IP address settings manually, select [Manually] in the Configure IPv4 field and enter values for each setting.
• When using access restrictions, you can register up to 16 users for the AirStation. • Please note that you are not allowed to use any of the following words as a user or group name: adm, administrator, all, bin, daemon, disk, ftp, guest, halt, hdusers, kmen, lp, mail, man, news, nobody, nogroup, none, operator, root, shadow, shutdown, sshd, sync, sys, ttyusers, utmp, uucp, www.
Appendix F Technical Detail of the USB port • If you view the size of a hard drives on the browser, it shows a bigger value than when you see it in Windows’ drive properties. This is because the browser shows the size of the drive in gigabytes but Windows shows it in gibibytes.
Appendix G - Regulatory Compliance Information Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Caution: The device for the band 5150-5250 MHz is only for indoor usage to reduce potential for harmful interference to co-channel mobile satellite systems. High power radars are allocated as primary users (meaning they have priority) of 5250-5350 MHz and 5650-5850 MHz and these radars could cause interference and/or damage to LE-LAN devices.
This device may not be used for setting up outdoor radio links in France and in some areas the RF output power may be limited to 10 mW EIRP in the frequency range of 2454 – 2483.5 MHz. For detailed information the end-user should contact the national spectrum authority in France.
Directive 1999/5/EC. Español [Spanish] Por medio de la presente Buffalo Technology Inc. declara que el AirStation WZR-HP-AG300H cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.
Nederlands [Dutch] Hierbij verklaart Buffalo Technology Inc. dat het toestel AirStation WZR-HP-AG300H in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/ Malti[ Maltese] Hawnhekk, Buffalo Technology Inc. , jiddikjara li dan AirStation WZR-HP-AG300H jikkonforma mal- ħtiġijiet essenzjali u ma provvedimenti oħrajn relevanti li hemm fid-Dirrettiva 1999/5/EC.
Safety This equipment is designed with the utmost care for the safety of those who install and use it. However, special attention must be paid to the dangers of electric shock and static electricity when working with electrical equipment. All guidelines of this manual and of the computer manufacturer must therefore be allowed at all times to ensure the safe use of the equipment.
• In order to avoid the dissemination of those substances in our environment and to diminish the pressure on the natural resources, we encourage you to use the appropriate take-back systems. • The take-back systems will reuse or recycle most of the materials of your end life equipment in a sound way.
All expressed and implied warranties for the Buffalo Technology (Buffalo Inc) product line including, but not limited to, the warranties of merchantability and fitness of a particular purpose are limited in duration to the above period. Under no circumstances shall Buffalo Technology/(Buffalo Inc.) be liable in any way to the user for damages, including any lost profits, lost savings or other incidental or consequential damages arising out of the use of, or inability to use the Buffalo products.