Pioneer DEH-1300 Installation Manual

DEH-2300
DEH-1300
DEH-23
DEH-12
This product conforms to CEMA cord colors.
Le code de couleur des câbles utilisé pour ce produit
est conforme à CEMA.
Los colores de los cables este producto se conforman
con el código de colores CEMA.
Printed in
Imprimé
<CRD3280-B/JS> UC <KKYLL/00G00000>

Connecting the Units

Note:
• This unit is for vehicles with a 12-volt battery • When this product's source is switched ON, a
and negative grounding. Before installing it in a control signal is output through the blue/white
recreational vehicle, truck, or bus, check the bat- lead. Connect to an external power amp's system
tery voltage. remote control or the car's Auto-antenna relay
• To avoid shorts in the electrical system, be sure control terminal (max. 300 mA 12 V DC). If the
to disconnect the ≠ battery cable before begin-
car features a glass antenna, connect to the anten-
ning installation. na booster power supply terminal.
• Refer to the owner's manual for details on con- • When an external power amp is being used with
necting the power amp and other units, then this system, be sure not to connect the blue/white
make connections correctly. lead to the amp's power terminal. Likewise, do
not connect the blue/white lead to the power ter-
• Secure the wiring with cable clamps or adhesive
minal of the auto-antenna. Such connection could
tape. To protect the wiring, wrap adhesive tape
cause excessive current drain and malfunction.
around them where they lie against metal parts.
• To avoid short-circuiting, cover the disconnected
• Route and secure all wiring so it cannot touch
lead with insulating tape. Especially, insulate the
any moving parts, such as the gear shift, hand-
unused speaker leads without fail. There is a pos-
brake and seat rails. Do not route wiring in
sibility of short-circuiting if the leads are not
places that get hot, such as near the heater outlet.
insulated.
If the insulation of the wiring melts or gets torn,
• If this unit is installed in a vehicle that does not
there is a danger of the wiring short-circuiting to
have an ACC (accessory) position on the ignition
the vehicle body.
switch, the red lead of the unit should be con-
• Don't pass the yellow lead through a hole into
nected to a terminal coupled with ignition switch
the engine compartment to connect to the battery.
ON/OFF operations. If this is not done, the vehi-
This will damage the lead insulation and cause a
cle battery may be drained when you are away
very dangerous short.
from the vehicle for several hours. (Fig.1)
• Do not shorten any leads. If you do, the protec-
tion circuit may fail to work when it should.
• Never feed power to other equipment by cutting
the insulation of the power supply lead of the
unit and tapping into the lead. The current capac-
ity of the lead will be exceeded, causing over-
heating.
• When replacing fuse, be sure to use only fuse of
the rating prescribed on this unit.
• Since a unique BPTL circuit is employed, never ACC position No ACC position
wire so the speaker leads are directly grounded or
the left and right ≠ speaker leads are common.
• The black lead is ground. Please ground this lead
• Speakers connected to this unit must be high-
separately from the ground of high-current prod-
power types with minimum rating of 45 W
(50 W)* and impedance of 4 to 8 ohms. ucts such as power amps.
Connecting speakers with output and/or imped- If you ground the products together and the
ground becomes detached, there is a risk of dam-
ance values other than those noted here may
age to the products or fire.
result in the speakers catching fire, emitting
smoke, or becoming damaged.
* DEH-2300 and DEH-23 • Cords for this product and those for other prod-
ucts may be different colors even if they have the
same function. When connecting this product to
another product, refer to the supplied Installation
manuals of both products and connect cords that
have the same function.
Connection Diagram
This product
Rear output
Antenna jack
Yellow
To terminal always supplied
with power regardless of
ignition switch position.
Red
To electric terminal controlled
by ignition switch (12 V DC)
ON/OFF.
Black (ground)
To vehicle (metal) body.
Fig. 1
With a 2 speaker system, do not connect
anything to the speaker leads that are not
connected to speakers.
Perform these connections when using a
different amp (sold separately).
Connecting cords
with RCA pin plugs
(sold separately).
Fuse
Blue/white
To system control terminal of the power amp or Auto-antenna
relay control terminal (max. 300 mA 12 V DC).
System remote control
White Gray
+
Front speaker
≠
White/black Gray/black
Left
Green Violet
+
Rear speaker
≠
Green/black Violet/black
+
Rear speaker
≠
<ENGLISH>
Power amp
(sold separately)
+
Front speaker
≠
Right
+
Rear speaker
≠
+
Rear speaker
≠
Fig. 2