Advertisement
Smart Vision Sensors
ZFV Color Series
Ordering Information
Models
Sensor Heads
Appearance
Narrow View
Standard View
Wide View
Ultra-wide View
Amplifier Units ZFV Color Series
Appearance
Accessories ZFV Color Series (order separately)
Data Storage Units
Appearance
Power supply
24 VDC
Controller Link Unit
Appearance
ZS-XCN
External Lighting
Type
Bar Lighting
Bar Double Lighting
Bar Low-angle Lighting
Light Source for Through-beam Lighting
ZFV
Type
Setting distance
34 to 49 mm (variable)
31 to 187 mm (variable)
66 to 141 mm (variable)
114 to 226 mm (variable)
Power supply
24 VDC
Output type
Model
NPN
ZS-DSU11
PNP
ZS-DSU41
Model
Model
ZFV-LTL01
ZFV-LTL02
ZFV-LTL04
ZFV-LTF01
Sensing area
5 × 4.6 mm to 9 × 8.3 mm (variable)
10 × 9.2 mm to 50 × 46 mm (variable)
50 × 46 mm to 90 × 83 mm (variable)
90 × 83 mm to 150 × 138 mm (variable)
Output type
NPN
PNP
Sensor Head Extension Cable
Cable length
3 m
8 m
*1.
ZFV-XC3BR Robot Cable is also available.
Panel-mounting Adapter
Appearance
Model
ZS-XOM1
First Unit
Model
ZFV-SC10
ZFV-SC50
ZFV-SC90
ZFV-SC150
Model
ZFV-CA40
ZFV-CA45
Model
*1
ZFV-XC3B
ZFV-XC8B
ZS-XPM2
Additional Units
(for expansion)
C-1
Advertisement
Table of Contents
Related Manuals for Omron ZFV
Summary of Contents for Omron ZFV
-
Page 1: Ordering Information
Setting distance Sensing area Model Narrow View 34 to 49 mm (variable) 5 × 4.6 mm to 9 × 8.3 mm (variable) ZFV-SC10 Standard View 31 to 187 mm (variable) 10 × 9.2 mm to 50 × 46 mm (variable) -
Page 2: Specifications
(Including the current consumed when external light is connected) Dielectric strength 1,000 VAC, 50/60 Hz for 1 min Vibration resistance 10 to 150 Hz, 0.35 mm single amplitude, 10 times each in X, Y, and Z directions for 8 min (destructive) Shock resistance 150 m/s... - Page 3 1 kV, Pulse rise: 5 ns, Pulse width: 50 ns, Burst duration: 15 ms, Cycle: 300 ms Vibration resistance ( destructive 10 to 150 Hz, 0.1 mm single amplitude, 10 times each in X, Y, and Z directions for 8 min destructive Shock resistance (...
- Page 4 Appprox. 210 mA Dielectric strength 300 VAC, 50/60 Hz for 1 min Vibration resistance 10 to 150 Hz, 0.35 mm single amplitude, 10 times each in X, Y and Z directions for 8 min (destructive) Shock resistance 150 m/s , 3 times each in six directions (up/down, left/right, forward/backward)
-
Page 5: Dimensions (Units: Mm)
ZFV-SC10 (Narrow view) 18.7 Two, M4 Depth: 6 Connector Mounting Hole Dimensions 20±0.1 Two, M4 Mounting Bracket can be attached to any side 67.90 Focus adjustment dial 0.80 17.90 4.5 4.5 (6.36) Heat-resistive vinyl-insulated cable 5.8 dia, standard length: 2 m 23.30... - Page 6 ZFV-SC150/SC150W (Ultra wide view) 110.2 59.5 Heat-resistant PVC shielded cable 6.2 Standard length 2 m Mounting surface 2-M4 20 ± 0.1 Mounting hole dimensions Amplifier Units ZFV-CA4@ 23.2 52.50 4.61 4.30 3.90 10.80 32.90 24.20 11.7 dia. Vision Systems...
- Page 7 External light units (optional) ZFV-LTL01 (bar lighting) 2 × 3-M3 Depth 5 P5.8 × 9 = 52.2 37.4 8 ± 0.1 20 ± 0.1 Mounting hole dimensions 10.7 69 ± 0.1 2-M3 Depth 5 Mounting hole dimensions ZFV-LTL02 (bar double-lighting) 4-M4 (Thru) 59.9...
- Page 8 59.9 90° P5.8 × 9 = 52.2 2000 +100 100 ± 0.1 100 ± 0.1 Mounting hole dimensions ZFV-LTF01 (light source for through-beam lighting) (Emitting surface) 4-M3 Depth 8 74 ± 0.1 74 ± 0.1 Mounting hole dimensions Vision Systems...
-
Page 9: About The I/O Cable
This connects the power supply. Use a DC power supply with safe extra-low-voltage circuits to prevent high voltage. Wire the power supply separately from other devices. Wiring them together or placing them in the same duct may cause induction, resulting in malfunction or damage. -
Page 10: I/O Circuit Diagrams
I/O Circuit diagrams NPN output type (ZFV-CA40) Brown Power supply (24VDC) Load Black OUTPUT Load Orange ENABLE Load Light blue ERROR 24VDC Blue GND(0V) Yellow TEACH Pink TRIG Gray BANK1 Green BANK2 BANK3 PNP output type (ZFV-CA45) Brown Power (24VDC) -
Page 11: Timing Charts
The measurement cycle changes depending on the setting. ENABLE Synchronuos measurement Measurement is performed only once in synchrnous with the change in TRIG signal state from OFF to ON and the result is output. TRIG Tout Tout: Measurement time. The measurement time changes OUTPUT depending on the setting. - Page 12 If the TEACH signal is turned OFF midway, teaching is disabled. Workpiece move teaching Use this teaching mode when the object cannot be stopped. Teaching processing is divided up and performed in synchronous with the TRIG signal input after the TEACH signal is input.