Omron E5AN-H User Manual page 360

Press the PF Key
for at least 1 s.
Press the O Key less than 1 s.
Adjustment Level
Adjustment Level
Display
Displayed only
l.adj p
c
once when
entering
8.0
adjustment level.
M
M
at i
AT Execute/Cancel
off 233.0
M M
cmwt d
Communications
off Writing 40.0
M
M
c-sc
irda Infrared Communications Use
1.00
off
M
M
c-db
spmd
SP Mode
0.0
lsp
M
M
of-r
ct1
Heater Current 1
Value Monitor 50.0
0.0
M
M
hys
hb1
Heater Burnout
1.0
Detection 1
0.0
M
M
chys
oc1
Heater Overcurrent
Detection 1 1.0
50.0
M
M
soak
ct2
Heater Current 2
1
0.0 Value Monitor
M
M
wt-b
hb2
Heater Burnout
off
Detection 2
0.0
M
M
mv-s
oc2
Heater Overcurrent
0.0
Detection 2
50.0
M
M
mv-e
lcr1
Leakage Current 1
0.0
Monitor
0.0
M
M
sprt
hs1
HS Alarm 1
off
50.0
M
M
ol-h
lcr2
Leakage Current 2
105.0
Monitor
0.0
M
M
ol-l
hs2
HS Alarm 2 -5.0
50.0
M
M
orl
c ins
Temperature Input Shift
0.0
0.00
M
M
1-point shift
Set either
db
Upper Limit
c insh of these
Temperature
parame-
2.0
0.00
Input Shift Value
ters.
M
M 2-point shift
oc-h
Lower Limit
insl
c
Temperature
0.8
0.00 Input Shift Value
M
M
sqrp
0.0
M
Note:
1. When the PF Setting parameter is set to A-M for a Controller with a PF Key (E5AN/EN-H).
2. When the PF Setting parameter is set to PFDP for a Controller with a PF Key (E5AN/EN-H).
Starting in manual mode.
Manual Control Level
PID
25.0
c
Control
only
100.0
PV/MV
(See note 1.)
Process Value
c 25.0
Added when Additional
PV display is ON.
Proportional Band
M
c 25.0
Process Value/
Set Point
0.0
Integral Time
M
PID settings
Auto/Manual Switch
a-m
PID control only.
Press Added when auto/man-
Derivative Time
ual select addition is ON.
the O
M
Key for
at least
bank Bank No.
3 s.
0
Cooling Coefficient
M
Heating/cooling
rsp Remote SP Monitor
c
Dead Band 0.0
M
Manual Reset Value sp-m
Set Point During
Clear the offset during
SP Ramp
0.0
stabilization of P or PD
control.
M
ct1
Heater Current 1 Value
Hysteresis (Heating) Monitor
0.0
M
Hysteresis settings
ct2
Heater Current 2 Value
Monitor
Hysteresis (Cooling)
0.0
M
lcr1
Soak Time Leakage Current 1
Monitor
0.0
M
lcr2
Leakage Current 2
Wait Band
Monitor
0.0
M
prst
MV at Stop
Program Start
rset
M
sktr
MV at PV Error
Soak Time Remain
0
M
SP Ramp Set Value
MV Upper Limit
MV Lower Limit
PF Key (See note 2.)
Monitor/Setting Item Level
MV Change Rate Limit
Position Proportional
Monitor/Setting
25.0
Dead Band
Item Display 1
0.0
Open/Close Hysteresis
Extraction of Square
Root
Note: The monitor/setting items to be displayed is set in the Monitor/Setting Item 1 to
Low-cut Point
5 parameters (advanced function setting level).
Power ON
Press the O
Starting in
Key or the PF
automatic
Key for at least
mode.
1 s.
(See note 1.).
Operation Level
r-s
RUN/STOP
run
M
c al-1
Alarm Value 1
0.0
M
al1h
c
Alarm Value
Upper Limit 1
0.0
M
c al1l
Alarm Value
Lower Limit 1
0.0
M
c al-2
Alarm Value 2
0.0
M
al2h
c
Alarm Value
Upper Limit 2
0.0
M
al2l
c
Alarm Value
Lower Limit 2
0.0
M
al-3
c
Alarm Value 3
0.0
M
al3h
Alarm Value
Upper Limit 3
0.0
M
al3l
Alarm Value
Lower Limit 3
0.0
M
o
MV Monitor (Heating)
0.0
M
c-o
MV Monitor (Cooling)
0.0
M
v-m
Valve Opening
Monitor
0.0
M
(E5AN/EN-H only)
Monitor/Setting
PF PF
Item Display 2
Monitor/Setting
Monitor/Setting
PF
Item Display 4
Item Display 5
PF Key (See note 2.)
Appendix
Press the O
and M Keys for
at least 3 s.
Press the O
and M Keys for
at least 1 s.
Monitor/Setting
Item Display 3
PF
339