Advertisement
Quick Links
Enclosed Switch
Economical, High Utility Enclosed
Switch
High precision and long life (10,000,000 mechani-
cal operations) through employment of the moving
spring used in OMRON Z Basic Switch.
Sealed with gasket diaphragm to provide high
sealing property without use of any adhesive or pin.
Suitable for applications demanding higher me-
chanical strength, dustproof and drip-proof proper-
ties than those on basic switches.
Panel mount versions have the same operating
position as Z Basic Switch.
Resin molded terminal versions are available.
Ordering Information
Model Number Legend
D4MC-
1
1. Actuator
5000: Panel mount plunger
5020: Panel mount roller plunger
5040: Panel mount crossroller plunger
1020: Short hinge lever
1000: Hinge lever
2000: Hinge roller lever
2020: Short hinge roller lever
3030: One-way action short hinge roller lever
List of Models
Actuator
Panel mount plunger
Panel mount roller plunger
Panel mount crossroller plunger
Short hinge lever
Hinge lever
Hinge roller lever
Short hinge roller lever
One-way action short hinge roller lever
Note: 1. Use molded terminal models (refer to page 209) when using the Switch under one of the following conditions:
a) dusty, b) high amount of dripping oil, or c) high humidity
2. Micro-load models are available.
e.g. Standard model
D4MC-5020
D4MC-5000
D4MC-5020
D4MC-5040
D4MC-1020
D4MC-1000
D4MC-2000
D4MC-2020
D4MC-3030
Micro-load model
D4MC-5020-C
D4MC
RC
Model
1
Advertisement
Related Manuals for Omron D4MC
Summary of Contents for Omron D4MC
-
Page 1: Ordering Information
One-way action short hinge roller lever D4MC-3030 Note: 1. Use molded terminal models (refer to page 209) when using the Switch under one of the following conditions: a) dusty, b) high amount of dripping oil, or c) high humidity 2. Micro-load models are available. -
Page 2: Specifications
Note: 1. The above figures are for steady-state currents. 2. Inductive loads have a power factor of 0.4 min. (AC) and a time constant of 7 ms max. (DC). 3. Lamp load has an inrush current of 10 times the steady-state current. - Page 3 15 m max. (initial value) Dielectric strength 1,000 VAC, 50/60 Hz for 1 min between terminals of the same polarity 2,000 VAC, 50/60 Hz for 1 min between current-carrying metal parts and ground, and between each terminal and non-current-carrying part Rated insulation voltage (U...
-
Page 4: Operation
Overtravel (mm) Operation Contact Form Dimensions Note: 1. All units are in millimeters unless otherwise indicated. 2. Unless otherwise specified, a tolerance of 0.4 mm applies to all dimensions. Panel Mount Plunger (See note 1) M12 x 1 mounting screw D4MC-5000 Two hexagon nuts 8.4 dia. - Page 5 Two hexagon nuts (thickness: 3 width: 17) (See Note: 1. Stainless steel roller note 2) dia. 2. The length of the imperfect threads is 1.5 mm maximum. 22 max. (21 x 21) Seal rubber (NBR) Terminal Two, 4.3 0.1 dia. protective...
- Page 6 Molded Terminal Models Molded Terminal Models The molded terminal model is available with right-hand, left-hand and underside leads and is recommended for use where the Switch is ex- posed to dust, oil, or moisture. When placing your order for the Switch specify the required length of V.C.T.
-
Page 7: Correct Use
2.94 to 4.92 N m Side mounting screw 1.18 to 1.47 N m Rubber packing Rubber packing ALL DIMENSIONS SHOWN ARE IN MILLIMETERS. To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527. Cat. No. C027-E1-7...