TEFAL SUPERGLIDE Manual
TEFAL SUPERGLIDE Manual

TEFAL SUPERGLIDE Manual

Hide thumbs Also See for SUPERGLIDE:

Advertisement

Available languages

Available languages

Spray Button to moisten linen
Water tank filler
cover
Steam control
Anti-calc valve
To be cleaned once
per month
Spray
Water tank maximum fill line
Sole plate
Do not exceed this limit
What water to use ?
Your appliance has been designed to function with tap water. However, it is necessary to
operate the Self-Clean function regularly in order to eliminate hard water deposits. If
your water is very hard (check with your water authority), it is possible to mix tap water
with store-bought demineralized water in the following proportions :
50% tap water, 50% demineralized water.
Types of water not to use :
Heat concentrates the elements contained in water during evaporation. The types of
water listed below contain organic waste or mineral elements that can cause spitting,
brown staining, or premature wear of the appliance: water from clothes dryers, scented
or softened water, water from refrigerators, batteries, or air conditioners, pure distilled
water, or rain water.
Please read these instructions carefully
and keep for future reference.
SUPERGLIDE
Shot of Steam Button
for removing wrinkles
Auto-Stop safety warning light
(depending on model)
Warning ! Remove the sole plate protector before
heating up the iron (depending on the model).
Warning !
Before using your iron with the steam function
for the first time, we recommend that you
operate it in horizontal position for a few
moments, away from your linen, ie press several
times on the shot of steam button.
During the first few uses, a harmless odour and
smoke may be given off.This has no effect on
the use of the iron and will disappear quickly.
(depending on model)
Thermostat indicator light.
Goes out when the temperature has
been reached.
Thermostat control
For choosing the ironing temperature
Electric power
cord

Advertisement

Table of Contents
loading

Summary of Contents for TEFAL SUPERGLIDE

  • Page 1 Your appliance has been designed to function with tap water. However, it is necessary to operate the Self-Clean function regularly in order to eliminate hard water deposits. If your water is very hard (check with your water authority), it is possible to mix tap water with store-bought demineralized water in the following proportions : 50% tap water, 50% demineralized water.
  • Page 2 - Unplug your iron before filling it. - Set the steam control on DRY (A). - Open the water tank filler cover completely (B), set the iron on a table (not when the iron is hot) shown in the diagram (C) below, and fill the tank.
  • Page 3 - Set the thermostat control on MAX (I). - Press the shot of steam button ( ) repeatedly (J), moving the iron from top to bottom (K). - Hold the iron a few centimetres from the fabric to avoid burning delicate fabrics.
  • Page 4 - Place the steam control on MAX. - Raise the anti-calc valve without removing it completely. - Shake the iron gently, over the sink, until all of the water in the water tank (with the impurities) has flowed out via the sole plate.
  • Page 5: For Your Safety

    • This iron must always be plugged into an earthed socket. • If using a mains extension lead, ensure that it is correctly rated (10 A or 13 A for UK only), with an earth. • If the electrical cord becomes damaged, it must be immediately replaced by an Approved Service Centre to avoid any danger.
  • Page 6 If you have any problem or queries, please contact our Customer Relations team first for expert help and advice.
  • Page 7 Si votre eau est très calcaire (ceci est vérifiable auprès de votre mairie ou du service des eaux), il est possible de mélanger l’eau du robinet avec de l’eau déminéralisée du commerce dans les proportions suivantes : - 50% d’eau du robinet, - 50% d’eau déminéralisée.
  • Page 8 - Débranchez votre fer avant de le remplir. - Placez la commande vapeur sur SEC (A). - Tirez le tiroir de remplissage du réservoir au maximum (B), posez le fer sur une table suivant le schéma (C) ci-dessous et remplissez le.
  • Page 9 - Appuyez sur la touche Super Pressing ( ) par impulsions(J) et effectuez un mouvement de haut en bas.Visuel (K) - Maintenez le fer à quelques centimètres du tissu pour ne pas brûler les textiles délicats. Sécurité Auto-Stop (selon modèle) - Le système électronique coupe l’alimentation et le voyant...
  • Page 10 - Remplissez le réservoir jusqu’à la limite (voir nos conseils sur l’eau à utiliser). - Laissez le tiroir de remplissage du réservoir ouvert jusqu’à la fin de l’opération. - Posez votre fer sur son talon et placez la commande du thermostat sur MAX. - Branchez votre fer et attendez que le voyant s’éteigne.
  • Page 11 Pour tout problème, adressez-vous à un centre service agréé pour faire vérifier votre fer.

Table of Contents