Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. CAUTION: Do not attempt to modify this product in any way without written authorization from Zenith Electronics Corporation. Unauthorized modification could void the user’s authority to operate this product. COMPLIANCE:...
Safety Instructions Safety Instructions WARNING : To reduce the risk of fire or electric shock, DO NOT expose this apparatus to rain or moisture. Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus.
Page 4
Safety Instructions Safety Instructions continued Safety Instructions continued 12. Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart / apparatus combination to avoid injury from tip-over. 13.
Introduction Introduction Introduction Controls Controls Remote Control Sensor Power/Standby Indicator Glows red in Standby mode, Glows green when the TV is turned on. ENTER MENU VIDEO On/Off Button Channel Buttons Volume Buttons Enter Button Menu Button TV·Video Button...
Introduction Remote Control Key Functions Remote Control Key Functions - When using the remote control, aim it at the remote control sensor on the TV. MUTE Switches the sound on or off. TV/VIDEO Selects: mode. FCR (Favorite Channels Review) Press to step through favorite channels.
DVI to D-Sub cable (PC) NOTES a. If the TV feels cold to the touch, there may be a small “flicker” when when it is turned on. This is normal, there is nothing wrong with TV. b. Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots. However, they have no adverse effect on the monitor's performance.
* The connection panel is hidden behind the rear cover. a. Remove the rear cover. ire Holders ire Holders - Thread, then pull the wires through the hole on the TV stand. Adjusting the Adjusting the TV V TV V...
- If you have a 75Ω round cable, insert the bronze wire and then tighten the connection nut. If you have a 300Ω flat wire, connect the twisted wire to the antenna converter and then connect the converter to the antenna jack on the TV.
- If your cable service does not require a converter box, refer to the Antenna Connection instructions. - After subscribing to a local cable TV service and installing a converter, you can watch cable TV programming. - For further cable TV information, contact a local cable service provider.
) jacks and connect the DVD audio outputs to the AUDIO jacks. Component Video jacks on other devices may not be labeled the same as they are on this TV, refer to the chart below for a list of other labeling schemes. Component ports...
NOTES a. For optimum picture quality, use standard WXGA 1280x768 (Z23LZ5R / Z26LZ5R), 1360x768 (Z32LZ5R) computer output at a 60Hz refresh rate . Using other formats (VGA, SVGA, etc.) or refresh rates may result in reduced picture quality. (To change the computer video output format, please refer to the operating manual for the computer you are using).
NOTE • If you want to turn the TV off, press the on/off button located on the TV. If you intend to be away on vacation, disconnect the power plug from the wall power outlet. Menu Language Selection Menu Language Selection - The menus can be shown on the screen in the selected language.
Memorizing the Channels with EZ scan Memorizing the Channels with EZ scan - For Auto program to work, the programming source must be connected to the TV and the TV must be receiving programming sig- nals either over-the-air or from a cable-type service provider.
Favorite Channels Setup Favorite Channels Setup - Favorite Channel lets you quickly tune in up to 8 channels of your choice without having to wait for the TV to scan through all the in-between channels. Channel EZ Scan Manual prog.
5. Press the ENTER button to save. Cinema Mode Setup Cinema Mode Setup - Sets up the TV for the best picture appearance for viewing movies. Press the MENU button and then use D D / E E 2. Press the...
Audio Audio - This function lets you enjoy the best sound without any special adjustment because the TV selects the appropriate sound option based on the program content. 1. Use the audio button to select the appropriate sound setup as shown below.
Stereo/SAP Broadcasts Setup - The TV can receive MTS stereo programs and any SAP (Secondary Audio Program) that accompanies the stereo program, if the broadcaster transmits an additional sound signal as well as the original one. - Mono: The primary language is heard from left and right speakers. Signal mode is mono.
Menu Options imer Menu Options Auto Clock Setup Auto Clock Setup The time can be automatically set using information from your local PBS TV station. The PBS channel signal includes information for the correct time and daylight savings time. Timer Clock...
- The TV must be in standby mode for the On-Timer to work. - If you don’t press any button within 2 hours after turning on the TV with the On-Timer function, the TV will automatically revert to standby mode.
• SNOW: If your receiver is located at the weak, fringe area of a TV signal, your picture may be marred by small dots. It may be necessary to install a special antenna to improve the picture. 2. An old, bad, or illegally recorded tape is being played.
2. Press the ENTER button to save. Key Lock Key Lock The TV can be set up so that it can only be used with the remote control to prevent unauthorized viewing. 1. Press the MENU button and then use D D / E E 2.
V-Chip rating and categories Rating guidelines are provided by broadcast stations. Most television programs and television movies can be blocked by TV Rating and/or Individual Categories. Movies that have been shown at the theaters or direct-to-video movies use the Movie Rating System (MPAA) only.
D D / E E Then, press the button. • If is already set, enter the password requested. • The TV is set with the initial password “0-0-0-0”. 2. Setting Lock on/off: Press the button to select D D / E E...
PC Menu Options PC Menu Options - After setup, be sure to select PC source to see the PC image on TV screen. H-Position V-Position Clock Phase Auto Configure Reset OK MENU 1. Press the MENU button and then use D D / E E 2.
External Control Device Setup External Control Device Setup External Control Device Setup External Control Device Setup The RS-232 port allows you to connect the RS-232C input jack to an external control device (such as a computer or an A/V control system) and control the Monitor’s functions externally. NOTE: RS-232 on this unit is intended to be used with third party RS-232 control software or hardware.
Page 29
* [Set ID]: You can adjust the set ID to choose desired monitor ID number in Special menu. Adjustment range is 1 ~ 99. When selecting Set ID ‘0’, every connected TV set is controlled. Set ID is indicated as decimal (1~99) on menu and as Hexa decimal (0x0~0x63) on transmission/receiving protocol.
Page 30
Data 0 : Power Off : Power On 02. Input Select (Command:b) (Main Picture Input) G To select input source for the TV. You can also select an input source using the TV/VIDEO button on the TV's remote control. Transmission [k][b][ ][Set ID][ ][Data][Cr]...
Page 31
G Tune channel to following Physical/major/minor number. Transmission [m][a][ ][Set ID][ ][Data0][ ][Data1][Cr] Data0: Channel Number Min : 1 ~ Max : 0x7D(transmit by Hexadecimal code) Data1:TV-0, CATV-1 (transmit by Hexadecimal code) Acknowledgement [a][ ][Set ID][ ][OK][Data0][Data1][x] [a][ ][Set ID][ ][NG][Data0][x] 15. Channel Add/Del (Command:m b) G To add and delete the channels.
IR Codes IR Codes IR Codes IR Codes How to Connect How to Connect G Connect your wired remote control to the Remote Control port on the Monitor. Remote Control IR Code Remote Control IR Code G Output waveform Single pulse, modulated with 37.917KHz signal at 455KHz G Configuration of frame •...
Page 33
POWER OFF Discrete IR Code TV/VIDEO R/C Button (TV/Video/S-video/Component1-2/RGB/DVI) MULTIMEDIA R/C Button (Component1-2/PC/TV) Discrete IR Code (Input TV Selection) Video Discrete IR Code (Input Video Selection) S-video Discrete IR Code (Input S-video Selection) Component 1 Discrete IR Code (Input Component 1 Selection)
Absence Extended Absence If you leave your TV dormant for a long time (such as a vacation), it’s a good idea to unplug the power cord to protect against possible damage from lightning or power surges. Product Specifications Product Specifications...
roubleshooting Checklist roubleshooting Checklist SYMPTOMS No power No picture or sound Poor picture but good sound Poor reception Lines in picture Ghosts (multiple images) Remote control does not work. Cannot tune desired channel. CHECK THESE THINGS Is power cord plugged in ? Is television turned on ? Check batteries in remote control.
Page 36
P/NO : 3828TUL271Z(0412-REV00) Printed in Korea...