Zenith H2546DT Installation And Operating Manual, Warranty page 32

Installer Menus
*Note: Page 31, Page 32
Changing TV Mode Values Installer menu options: 01 PRESET PX (Preset Picture),
03 VERT POS (Vertical Position), and 04 HORZ POS (Horizontal Position), have
separate values for TV mode and Computer mode. If you enter the installer menu
with the source being a TV channel, Aux, S-Video, or Camport, you change the val-
ues for TV mode only.
00 FACT MENU (Factory Menu)
Used to access and customize Service Menu: settings using the
installer type remote.
01 PRESET PX (Preset Picture)*
Saves your custom video settings (color, tint, contrast, and
brightness) in nonvolatile memory (not affected by power loss).
Memory status is indicated by a 1 for "custom settings already
stored," or 0 for "custom settings have not been stored."
Make all custom video settings before you access the Installer's
Menu: and PRESET PX. When you use the ADJUST keys to toggle
from 1 - 0, any changes in the video settings will be stored sure
they are correct! These settings become the PRESET values for the
PICTURE PREF option of the Video Menu. (For more information
refer to the Video Menu section of this manual.)
02 POWER MANAGE (Power Management)
The POWER MANAGE function is for saving energy. When set to 0,
Power Manage is OFF. Settings range from 0 - 7, with 1 - 7 repre-
senting the hours that the TV will remain on, unless there has
been activity from either the control panel or remote.
03 VERT POS (Vertical Position)*
Moves captions and displays vertically on the screen. Use the
Left/Right ADJUST arrows. Typical value is 15. Black bars top and
bottom define the active screen area.
04 HORZ POS (Horizontal Position)*
Moves captions and displays horizontally on the screen. Use the
ADJUST keys. Typical value is 34. Black bars top and bottom
define the active screen area.
05 BAND/AFC (Band/Automatic Frequency Control)
There are 8 possible settings for this option:
0 = Broadcast Fixed4 = Broadcast AFC
5 = CATV Fixed
6 = HRC Fixed
7 = ICC Fixed
Channels are accessed faster when fixed modes are used. The AFC
(search modes) should only be used when some channels are not
on nominal frequencies. NOTE: BAND is automatically set by AUTO
PROGRAM.
If some channels were not found by AUTO PROGRAM, select the
appropriate AFC setting here and add the channels using the
ADD/DEL option in the Setup Menu.
P A G E 3 2
1 = CATV AFC
2 = HRC AFC
3 = ICC AFC
Changing Computer Mode Values
To change values for Computer mode, press TV/VCR SOURCE to select REAR
COMPUTER SVGA or FRONT COMPUTER SVGA as the source, then enter the
installer menu. The changes you make will then apply to Computer Mode.
06 MIN VOLUME (Minimum Volume)
This function determines the minimum volume level allowable
with the VOLUME (VOL) Up/Down control. In this way, for exam-
ple, someone cannot set the volume too low to hear. The range is
from 0 to 63—change values with ADJUST . The factory default is
0, which provides full range of volume control. It may be best to
set the same value on every TV. NOTE: The minimum volume level
cannot have a value setting higher than in the MAX VOLUME level
(described below).
07 MAX VOLUME (Maximum Volume)
This function determines the maximum volume level allowable
with the VOLUME VOL Up/Down control. In this way, for example,
someone cannot set the volume level high enough to disturb oth-
ers. The range is 0 to 63, with 63 as the default which gives the
patient the full range of volume control. Change values with
ADJUST keys. It may be best to set the same value on every TV.
NOTE: The maximum volume level cannot have a value setting
lower than the MIN VOLUME level (described above).
08 AC ON (AC Power Switchable)
Allows the TV to turn ON just by applying AC power. Pressing the
ON button is not necessary. This is desirable when the TV is
plugged into a cable box or a power outlet controlled by a wall
switch. Use ADJUST to select 0 or 1, where 0 is the default is
OFF, and 1 is ON.
NOTE: When set to 1 (ON), the TV does not respond to ON/OFF
commands from either the remote or the control panel, and the
SLEEP TIMER is also nonfunctional.
9 KEY DEFEAT (Keyboard Defeat)
When set to 1, it prevents the end user from accessing screen
menus on the front panel—MENU, SELECT, and ADJUST do not
function. When set to 0, those keys are functional. The menus can
always be accessed with MENU on the remote.
10 STRT CH/VOL (Start Channel/Volume)
When active, this function allows you to determine the initial vol-
ume level setting and channel number when the TV is turned ON.
This feature is useful for an in-house information channel, since
the TV would always select that channel when it is turned on.
When inactive, the volume level and channel retain the settings
when the set was last used.
The range of values is 0 - 255.
Use the Left/Right Adjust arrow keys to choose:
Setting "1" With number 255 selected, the feature is inactive.
(When the TV is turned on, the Volume level and Channel number
will be the same Volume level and Channel number that were
selected before the TV was turned off.)
Setting "2" Other numbers determine the start-up (turn on)
channel.
206-3492-A