Advertisement
Quick Links
STUDIO
S
®
PRESSURE BALANCE BATH
AND SHOWER TRIM KIT
Thank you for selecting American Standard...
the benchmark of fine quality for over 140 years.
To ensure that your installation proceeds smoothly-please
read these instructions carefully before you begin.
For use with shower heads rated at 4.9 L/min (1.3 gpm) or higher.
RECOMMENDED TOOLS
Plumbers' Putty
or Caulking
ROUGHING-IN DIMENSIONS
• To assure proper positioning in relation to wall.
Note roughing-in dimensions.
FINISHED WALL
4-1/2"
(114 mm) REF.
74" (1880 mm)
11-7/8" (301 mm) REF.
FOR HEAD
CLEARANCE
18" (457 mm)
OPTIONAL
TOP OF TUB RIM
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2018
Phillips Screwdriver
Teflon Tape
Flat Blade Screwdriver
1-5/8" TO 3-1/4"
(41 TO 83 mm)
1/2" (12 mm) NPT
2-1/8"
(54 mm)
1-5/8" TO 3-1/4"
(41 TO 83 mm)
8"
(203 mm)
OPTIONAL TO FINISHED
FLOOR USUALLY
BETWEEN 65'' AND 80''
(1651 AND 2032 mm)
7-1/2" DIA.
(185 mm)
2-3/4" MAX. (69 mm)
1-3/4" MIN. (45 mm)
1-1/2" REF.
(38 mm)
6-1/8" REF.
(155 mm)
(102 mm)
1/2" (13 mm)
COPPER
BOTTOM OF TUB
INSTALLATION
INSTRUCTIONS
TU105500
TU105501
TU105502
TU105507
TU105508
Adjustable Wrench
1
CARTRIDGE INSTALLATION
• Remove PLASTER GUARD (6)
(Keep it installed for thin wall Installation).
• Remove BONNET NUT (1) by unthreading it
Counter clockwise. Remove test CAP (2).
• Remove PROTECTIVE HOUSING (3) from
CARTRIDGE (4). Install with "UP" text on top.
• Reinstall BONNET NUT (1) onto VALVE BODY (5)
and hand tighten.
4"
- 1 -
Channel Locks
5
1
3
4
2
M965930 Rev. 1.0 (8/18)
H
C
OFF
6
Advertisement
Related Manuals for American Standard STUDIO S TU105500
Summary of Contents for American Standard STUDIO S TU105500
- Page 1 TU105502 AND SHOWER TRIM KIT TU105507 TU105508 Thank you for selecting American Standard... the benchmark of fine quality for over 140 years. To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin. For use with shower heads rated at 4.9 L/min (1.3 gpm) or higher.
- Page 2 INSTALL VALVE TRIM (STANDARD WALL INSTALLATION) • Figure 1. Push CAP (1) over VALVE CARTRIDGE (2) until seated against stop. PLASTER GUARD • Figure 2. Make sure O-RING (6) is secure within ESCUTCHEON HOLDER (3). Push ESCUTCHEON HOLDER (3) onto CAP (1) and attach with LONG SCREWS (4). Mount ESCUTCHEON SUPPORT (5) to ESCUTCHEON HOLDER (3) with 4 SHORT SCREWS (8).
-
Page 3: Install Handle
INSTALL, TUB SPOUT, SHOWER HEAD, SHOWER ARM WITH FLANGE O-RING Protect finish on SHOWER HEAD CAUTION and TUB SPOUT when installing. Note: Apply sealant or Teflon Tape to shower arm. • Remove PIPE PLUG and CAP (1, 2) from shower pipe and tub filler pipe. -
Page 4: Care Instructions
SERVICE TO GAIN ACCESS TO VALVE FOR SERVICING Turn off hot and cold water CAUTION supplies before beginning. • Remove HANDLE (see step 3 and reverse). • Remove ESCUTCHEON and CARTRIDGE CAP (see step 1 and reverse). VALVE LEAKS WHEN SHUT OFF •... - Page 5 STUDIO ® PRESSURE BALANCE BATH AND SHOWER TRIM KIT MODEL NUMBERS TU105500 TU105501 TU105502 TU105507 TU105508 M919631-YYY0A SHOWER ARM M970255-YYY0A FLANGE & O-RING 1660528.YYY SHOWER HEAD 1.8 GPM 1660527.YYY SHOWER HEAD M970410-0070A 2.5 GPM CARTRIDGE 078016-YYY0A ESCUTCHEON SCREWS M907052-YYY0A M970484-0070A CARTRIDGE CAP MOUNTING PLATE EXTENSION...