Fastus BGS-HL Series Instruction Manual

Need Technical Support or Help with a Tough Application? Contact the experts at Ramco today!
High resolution BGS sensor
BGS-HL Series
BGS-HL05T □
BGS-HL25T □□
Instruction manual
- Thank you for purchasing BGS-HL series. We hope you are satisfied with its performance.
- Please read this manual carefully and keep it for future reference.
Indicates a possible hazard that may result in death, serious
injury, WARNINGS or serious property damage if the product is
used without observing the stated instructions.
Warning Mandatory Requirements
● The light source of this product applies the visible light semiconductor laser. Do not
allow the laser beam to enter an eye, either directly or reflected from reflective object. If
the laser beam enters an eye, it may cause blindness.
● This product is not an explosion proof construction. Do not use the product under flam-
mable , explosive gas or liquid environment.
● Do not disassemble or modify the product since it is not designed to automatically stop
the laser emission when open. Disassembling or modifying at customer's end it may
cause personal injury, fire or electric shock.
●Use of controls or adjustments or performance of procedures other than those specified
herein may result in hazardous radiation exposure.
Warning Safety Precautions
● It is dangerous to wire or attach/remove the connector while the power is on. Make sure
to turn off the power before operation.
● Installing in the following places may result in malfunction:
1. A dusty or steamy place
2. A place generating corrosive gas
3. A place directly receiving scattering water or oil.
4. A place suffered from heavy vibration or impact.
● The product is not designed for outdoor use.
● Do not use the sensor in a transient state at power on (Approx. 2sec. Warm up period)
● Do not wire with the high voltage cable or the power lines. Failure to do this will cause
malfunction by induction or damage.
● Do not use the product in water.
● Operate within the rated range.
● Wipe off dirt on the emitting/receiving parts to maintain correct detection. Also, avoid
direct impact on the product.
Precautions for using laser
● Regulations in the USA
When exporting laser devices to the USA, the USA laser control, FDA
(Food and Drug Administration) is applied. This product has been already
reported to CDRH (Center for Devices and Radiological Health). For
details, contact our customer service.
CLASS 2 LASER CLASS 1 LASER
Complies with 21 CFR 1040.10 and 1040.11
PRODUCT PRODUCT
except for deviations pursuant to
laser notice No.50, dated June 24, 2007
MAX. OUTPUT 1mW MAX. OUTPUT 390μW
OPTEX FA CO.,LTD.
WAVELENGTH = 655nm
WAVELENGTH = 655nm 91 Awata-cho Chudoji Shimogyo-ku Kyoto 600-8815 JAPAN
Place of manufacture :
EN/IEC 60825-1:2007 EN/IEC 60825-1:2007
OFROM CO.,LTD.
Complies with 21 CFR
Complies with 21 CFR
Manufactured in
1040.10 and 1040.11 1040.10 and 1040.11
except for deviations
except for deviations
pursuant to laser notice
pursuant to laser notice
No.50, dated June 24, 2007
No.50, dated June 24, 2007
Bundled goods in the box
Please confirm following goods bundled in the box.
・ ・This instruction manual
・Screws
M3 × 15...2
・Bracket
Connection diagram
■ NPN type
■ PNP type
■ Pins configuration ・ M8 connector type
( sensor side )
Dimensions
■ Cable type
4.5 4core 2m Cable
■ M8 connector type
M8 4pin
Connector
Ramco Innovations www.optex-ramco.com
Our email is nsales@ramcoi.com
Specifications
● Part number legend
●
Cable type BGS-HL05T
Part
Connector type BGS-HL05TC
number
Sensing range ※ 1 20 ~ 50mm
(Display: 0.00 ~ 30.00)
Light source Red laser Diode (wave length 655nm)
390μW
Laser IEC/JIS CLASS 1
class
Spot size ※ 2 φ 0.8 mm @ 50mm
Repeat accuracy 10μm
Sampling period 500μs / 1000μs / 2000μs / 4000μs / AUTO
Response time
1.5ms max. (1.5~7ms/default)
Hysteresis
0 ~ 22.49 (default: 0.15）
Display 7-segment 4-digit LED display
Indicator Laser indicator: Green,
Output indicator: Orange, Mode indicator: Red
Control Output NPN/PNP selectable
100mA max./DC24V (Residual voltage 1.8 V max.)
External Input Laser OFF, Teaching, Sample Hold, One shot hold
Timer function OFF/On delay/Off delay/One shot
1msec increment : 0 ~ 9999ms
Supply voltage 12 ~ 24VDC including 10% ripple
Current consumption 40mA max. / 24VDC excluding the current of Control Output
Protection circuit Reverse connection protection, Over current protection
Protection category
Operating Temp./Humid. -10 ~ 50℃ / 35 ~ 85% RH without freasing or condensation
Storage Temp./Humid. -20 ~ 60℃ / 35 ~ 85%/RH
Ambient illuminance Incandescent lamp: 3,000 lx max.
Vibration resistence 10 ~ 55Hz, Double amplitude 1.5mm, X,Y,Z for 2 hours
2
Shock resistence 500m/s ( approx. 50G) X,Y,Z 3 times each
Material Case: Aluminum, Front lens: PPSU, Display: PET
Weight Cable type : Approx. 90g (including cable)
Connector type : Approx. 30g
The specifications are based on the condition unless otherwise designated: Ambient temperature: 23℃ , Sup-
ply voltage: 24VDC, Sampling period: 500µs, Averaging: 512, Measuring distance: Center of the range, Testing
object: White ceramic
[mm]
※ 1 When [Shift] in Extension mode is ON, the display shows 0000 at the Teaching point.
The range that the display can show is as follows.
BGS-HL05 -7.50 ~ 37.50
BGS-HL25 -50.0 ~ 250.5
When the distance exceeds this range in Sensing range, the display shows FFFF. Although, the sensor
works while the distance is in Sensing range. The display shows 9999 when the distance is out of range.
2
※ 2 Defined by light strength within 1/e (13.5%) of spot center. There may be leak light at outside of the
specified spot size. The sensor may be affected when there is a highly reflective object at that leak light
area.
μs
※ 3 Sampling period : 1000 .
Display
Functions of components
● Control panel
Display
Got Questions? 1-800-280-6933
Setup
● Changing mode
While it's "Setup mode" or "Extension mode", you can change the mode to "RUN mode"
by clicking "TEACH/RUN" button.
While it's "Extension mode", the LED "MANUAL" is lit.
BGS-HL25T2
BGS-HL25TC2
50 ~ 250mm
(Display: 0.0 ~ 200.0)
1mW
CLASS 2
φ 1 mm @ 250mm
100μm ※ 3
1.5ms max. (3~14ms/default)
0 ~ 149.9 (default: 1.0）
● Changing parameters
You can choose and adjust the parameters by clicking "+" and "-" buttons.
The mode will be changed to "RUN mode" by clicking "TEACH/RUN" button.
IP67
Teach function
You can change threshold level directly by "+" and "-" buttons after clicking "TEACH/
RUN" button from "RUN mode".
By pressing "TEACH/RUN" button for 2 seconds or more, it gets to "Teaching mode". It
has 3 "Teaching mode" that you can choose one in "Setup mode".
Please refer "Teaching mode" and "Setup mode" on next page.