Downloading a AppGen Pro application from Host to WDT2200 ...34 5.2.2 Uploading AppGen Pro files from WDT2200 to HOST...34 5.2.3 Downloading a file from Host to WDT2200 using the Kermit Server ...35 5.2.4 Uploading files from WDT2200 to HOST using the Kermit Server ...36 CHAPTER 6.
Chapter 1. Introduction The WDT2200 is a programmable and flexible data collection device that can be utilized in a variety of data acquisition applications. It can be used as a portable data entry device or as a programmable dedicated computer that receives and runs application programs downloaded from a host computer.
& 1.2.2 Display Subsystem The WDT2200 display subsystem supports a character oriented 8-line by 20-character or 4-line by 16-character LCD display. The origin (0,0) is always at the top-left hand corner. This subsystem provides the program interface functions to display characters, set cursor position, get cursor position and clear screen display.
This subsystem allows users to set and obtain system date and time from the Real Time Clock Integrated Circuit (IC) in the WDT2200. 1.2.5 Bar Code Input Port The WDT2200 has a built-in barcode decoder. The terminal reads bar code labels through an integrated laser scanner module, pen type module. 1.3 Diagnostics and Power-On-Test The system diagnostic routines exercise the ROM validity check, test the RAM, system parameters, the keypad, the real time clock, the RS-232 port, LCD and scanner port.
______________________________________________________ Chapter 2. System Software Organization The WDT2200 system software is organized into two modules: the kernel module and the application module (see diagram below). APPLICATION Terminal MODULE module Workstation module User-device module RESIDENT APPLICATIONS KERNEL MODULE SCAN_INT EXEC Manager 2.1 Application Module...
Device configurations preserve the same values as they had before the warm boot. On the other hand, a cold boot will clear the RAM and initialize the WDT2200 to default values. The WDT2200 is always testing its main and backup batteries. The LCD will display a warning message when the test fails.
Page 8
“System Resume” is set to On when this flag verification fails. A program downloaded to the WDT2200 may be automatically executed each time the portable terminal is turned on. In order for the program to be auto-ran, it must be downloaded to THE WDT2200 with the name AUTOEXEC.EXE.
3.1 Keyboard Modes --- Using THE WDT2200’s keyboard The keypad of THE WDT2200 consists of 27 rubber keys, the power key is used to switch on/off the unit and other 26 keys are used to control the unit and key in data. Use of the keyboard is categorized to three modes: normal mode, command mode, and alpha(betic) mode.
NORMAL mode 3.1.1 Keyboard of the WDT2200 is initialized to normal mode after powered on. In normal mode, the cursor is a block sign and the keyboard is mainly used to input numeric data and use F1-F4 four function-keys. The keypad layout of available keys in normal mode is shown on right picture.
Supervisor Mode 3.2.1 Ready Mode The Ready mode is the default operating mode. In the Ready mode, the WDT2200 is configured as a portable programmable device, and is capable of receiving files (Download) from or transmitting files (Upload) to a Host PC. Data files or recorded information collected from the WDT2200 are uploaded to the host whenever the host program is ready to receive the collected data.
Page 12
If a terminating condition exists by the reception of a terminating character, the WDT2200 outputs the buffer to its RS232 port. Data transfer between the host machine and the WDT2200 is primarily controlled by the terminating conditions specified in the Terminal Control Table.
Page 13
Block mode applications perform similar functions to character mode, except that the input characters will not be sent to the host one character at a time. Instead the WDT2200 holds the data in its internal buffer until a termination character is received. Specifying the linepage, lineterm, and pageterm parameters in the terminal control table programs the termination character.
Page 14
[ ] or [ ] key to select an existing file then press [ENT]. The screen will display 160 (20 character x 8 line) characters at a time. Press any key to show the next page or press [CMD] then [Alpha], to warm start the WDT2200 and return to the Ready Mode. 3.2.2.7 The CPY command allows the user to make a copy of data from a source and transfer the information to a destination.
Page 15
DATE & TIME Set System Clock/Calendar By selecting “1.DATE & TIME” in the SET menu, you can set the WDT2200 date and time. The date and time can be used as the time stamp to be appended to an input data record by an application program.
To switch the WDT2200 to the Supervisor mode of operation do the following: 1. Turn off the WDT2200. 2. Press and hold down the [CMD] and [ ] keys simultaneously, then switch on the WDT2200 by pressing the power key. The WDT2200 LCD will show the ‘START MENU” where the user has three choices: 1.Enter the Supervisor mode, 2.Command the WDT2200 to execute a Warm...
Page 18
2.SERIAL The WDT2200 supports one RS232 port on a flat 12-pin connector. Data can be downloaded to and uploaded from the WDT2200 via the serial data communication port. The communication parameters must be set correctly in order to send/receive data via the RS232 port. The default settings for the serial port are...
Page 19
ASCII terminal when the user select this feature and disable the FormCaching menu. When the TERM SETUP menu (shown below) appears on the WDT2200 LCD, proceed to set up the portable terminal communication parameters. When finished, go to the User Mode menu and press 2 (2.TERM) to make the WDT2200 operate as an ASCII dumb terminal.
Page 20
AutoLF Use the [ ] key to toggle between ON or OFF, then hit [ENT] to make the selection. When AutoLF is set to ON, the WDT2200 will append a LF (10 hex) character to the input data block. Mode Use the [ ] key to toggle between BLOCK and CHAR, then hit [ENT] to make the selection.
Page 21
Enable the FormCaching application by selecting 4 (4.FORM) in the Supervisor mode menu. When FormCaching is enabled, the WDT2200 will first ask the user to specify data fields in four categories including field prompt, data length, and data type and device type. After defining all data fields, the user must press [CMD] then the [Alpha] key to end the setup of the data field.
Page 22
3.HHMMSS FIELD DELAY When FormCaching is enabled, a data file named FORM.DAT will be created in the WDT2200. FORM.DAT stores the data as entered by the user after FormCaching is invoked. The WDT2200 will not allow the user to redefine the data fields in FormCaching once the FORM.DAT has been created.
Page 23
Press [ENT] to complete the setting 2.AUTO OFF Use the [ ] key to set the auto-off timeout from 1 to 9 minutes. The WDT2200 will turn itself off automatically after being idle for the time period specified in the setting.
Page 24
Shutdown mode if the WDT2200 has been idle for the specified timeout period as set in ♦Shut Down In Shutdown mode, the main power is cut off from the WDT2200 excluding its RAM and Real Time Clock.
Page 25
3.2.3.7 Initialization The user can command the WDT2200 to execute a Cold Start that will clear all data stored in the RAM Disk and configure the terminal to default values. Make sure your data has been backed up to a Host/PC before performing this function.
Page 26
WDT2200 to your Host/PC. 3.2.3.8 Diagnostics 1. The WDT2200 has a built-in diagnostics program to test the terminal s hardware. The test routines are data destructive. Therefore, before running the diagnostic program, make sure you back up the data in the WDT2200.
The WDT2200 is a handheld data terminal that has an integrated laser-scanning module or clip- on pen module for bar code reading. A rechargeable Li-ion battery pack powers the WDT2200. A CR2032 lithium button cell backup battery preserves data stored in RAM when the power main battery is used up or during the replacement of the main battery.
Ext 9V 4.3.2 Scanner The WDT2200 has provision for an integrated laser or CCD scan engine and a built-in decoder for reading bar code labels. There is a single scanner-trigger switch above the keypad. The scanning window of the integrated unit sits flush with the top surface of the portable terminal.
An optional charging/communication cradle (docking station), gives users a convenient environment for daily use of the WDT2200. The cradle has provisions for a quick charge circuit to fully charge the main Li-ion battery pack installed in the unit in about 2~3 hours. The cradle also allows users to link the WDT2200 to a host computer through RS-232 for data communication.
COMMUNICATION INSTALLATION The RS-232 port of the WDT2200 can communicate with the serial port of a host computer. There are two ways to carry out communication sessions: (1) LOCAL : Directly connect to the serial port of your computer system.
Page 32
Once your WDT2200 has been connected with a modem to a telephone line, you can dial from the WDT2200 to a remote host computer. The computer needs to be attached to a modem through the telephone line. After the line is connected, the data communication process can start between the WDT2200 and PC/Host as if the two were linked locally.
5.3.1 Downloading an AppGen Pro application from Host to WDT2200 This function downloads an existing AppGen application from the host to the WDT2200. On the WDT2200: Connect the RS-232 port of the WDT2200 to the COM port of your PC by a null modem • cable.
5.3.3 Downloading a file from Host to WDT2200 using the Kermit Server This function downloads a file from host to the WDT2200. On the WDT2200: Connect the RS-232 port of the WDT2200 to the COM port of your PC via a null modem • cable.
Having collected the data into the WDT2200, the user can upload one or more collected data forms to your PC. On the WDT2200: Connect the RS-232 port of the WDT2200 to the COM port of your PC with a null modem • cable.
7. If the keypad does not work properly: Verify operation steps against the user manual, or • Power the WDT2200 off and on, then press some keys to check if an audible beep is • generated for each key pressed. If not, call for service.
Page 38
8. If encounter any other abnormal symptoms: Caution : The following process will clear all data in the WDT2200 RAM disk memory) Reset (cold start) the WDT2200, press [CMD], [ ] and the power key simultaneously, press [3] in “Start Menu” press ENTER. See if the symptoms go away. If not, call for service.
3 hours. The WDT2200 checks the power level of the main battery when the portable terminal is in use, however, the backup battery is only checked during power-on-test. Either low battery condition will signal the user via a warning message on the LCD.
MAIN BATTERY CHARGING WITH CRADLE Connect power adapter to the cradle and insert the WDT2200. The battery of PDT can be fully charged in about 2~3 hours and the status of battery charging is indicated by the LED on the front panel of the cradle.