Vivotek FD7141 Quick Installation Manual
Outdoor vandal-proof wdr network camera
Hide thumbs
Also See for FD7141:
- User manual (129 pages) ,
- Quick installation manual (15 pages) ,
- Technical specifications (2 pages)
Advertisement
Quick Links
Advertisement
Related Manuals for Vivotek FD7141
Summary of Contents for Vivotek FD7141
- Page 1 FD7141(V)
- Page 2 Contact your distributor in the event of occurrence. EN - 1...
- Page 3 Drill hole Ceiling Hole Template Sticker EN - 2...
- Page 4 SD Card Tilt Screw Slot Status LED Image Adjustment Screw f= 3.3~12 mm (FD7141 Lens) f= 9~22 mm (FD7141V Lens) Pan Screw Reccessed Reset Button Focus Controller Zoom Controller Ethernet 10/100 RJ45 Plug Audio Out (green) Microphone In (pink) Power Cord Socket (black)
-
Page 5: Dome Cover
Camera Base Record the MAC address under the camera base before installing the camera. Hole a~c: Holes for ceiling mount or for attaching the bottom base. Dome Cover Bottom Base MAC:0002D1083236 This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference... - Page 6 First, use a screwdriver to loose the three screws and detach the dome cover from the camera base. Then, follow the steps below to install the camera to either a ceiling or a wall. 1. Attach the supplied alignment sticker to the ceiling. 2.
- Page 7 1. Attach the supplied alignment sticker to the wall. 2. Using the 10 circles on the sticker, drill 2 pilot holes symmetrically on each side into the wall. Then hammer the four supplied plastic anchors into the holes. 3. Using the four holes on the bottom base, insert the four supplied screws to corresponding holes and secure the bottom base with a screwdriver.
- Page 8 1. Attach the supplied ceiling hole template sticker to the ceiling. 2. Open a hole along the inner circle of the sticker. 3. Using the 3 circles on the sticker, drill 3 pilot holes into the ceiling. Then hammer the three supplied plastic anchors into the holes.
- Page 9 The Network Camera is PoE-compliant, allowing transmission of power and data via a single Ethernet cable. Follow the below illustration to connect the Network Camera to a PoE-enabled switch via Ethernet cable. Use a PoE power injector (optional) to connect between the Network Camera and a non-PoE switch.
- Page 10 “Next” button to continue the program. Installation Wizard 2 3. The program will search for VIVOTEK Video Receivers, Video Servers, and Network Cameras on the same LAN. 4. After searching, the main installer window will pop up. Click on the MAC that matches the one labeled on the bottom of your device to connect to the Network Camera via Internet Explorer.
- Page 11 1. Access the Network Camera on the LAN. 2. Retrieve live video through a web browser or recording software. http://192.168.5.109/index.html For further setup, please refer to the user's manual on the software CD. EN - 10...
- Page 12 Based on the live image retrieved from the camera, adjust the camera lens by doing the following: 1. Loosen the pan screw and then turn the lens module left and right. Upon completion, tighten the pan screw. 2. Loosen the tilt screws on both sides of the camera and turn the lens module up and down.
- Page 13 If you are using (f= 9~22 mm), please hold the supplied plastic cover in front of the lens while adjusting the focus controller as shown below. axis of the lens Attach the dome cover to camera. Secure the three dome screws with the supplied screwdriver.
- Page 14 P/N:625007701G Ver.1.1 Copyright 2009 VIVOTEK INC. All rights reserved.