Yamaha RX-17 Authorized Product Manual page 39

34
* init PARAM. *
* illegal PTN
! ERROR !
! LOAD ERROR !
! VERIFY ERROR !
! Different Type !
! D a t a D e s t r o y e d !
! MIDI BUFFER !
I
! MEMORY FULL !
! TOO LARGE PTN !
Part Overflow !
Illegal lnput !
! CHANGE BATTERY !
! NO BATTERY !
End of SONG !
Not Found
! Already Set !
Sometimes you may see an unusual message on the RX17's LCD, indicating that an
operation has been executed wrongly, or there is a technical malfunction. This chart lists
those messages, their causes and remedies.
MESSAGE
A malfunction in the RX17 has caused all parameters
(voice level, accent level, pan, MIDI settings) to be
initialized.
A malfunction in the RX17 has caused all Pattern and
*
Song data to be cleared.
* illegal SONG*
o r
During MIDI Bulk Receive, incorrect data was sent due
to faulty cable or electrical interference.
There is a checksum error in sequence data that you
have tried to load from cassette, due to a fault in
transmission.
The RX17 contains different data to the data saved on
cassette.
During Bulk Receive, you are sending data to the RX17
that is not formatted for the RX17.
During Bulk Receive or Cassette Load, you have cleared
all data in the RX17 by attempting to load the wrong type
of data.
Too large amounts of MIDI data are being sent to the
! FULL !
RX17 too rapidly.
The RX17's Pattern or Song Memory is full, and further
data cannot be entered.
You have exceeded the maximum size of a Pattern, and
further data cannot be entered.
You have entered data in the Copy Part function which
would result in a Song containing more than 999 Parts.
1. You have entered Part numbers in the Copy Part
function where the second Part number is smaller
than the first.
2. You have entered Part numbers in the Copy Part
function which include the destination Part number.
You have entered a Part number in the Copy Part function
which is higher than the total number of Parts in the
Song.
You have tried to change the length of a Pattern that
already contains data.
The lithium battery, for memory backup, is running at
less than 2.2 V.
The lithium battery, for memory backup, is running at
less than 1.5 V.
!
1. In the Copy Part function, you have entered a copy
destination Part number that is higher than the total
number of Parts in the Song.
2. In the search Part function, you have entered a Part
number that is higher than the total number of Parts
on the Song.
CAUSE
Use operation 2.1.2 to load the Preset Patterns and
Songs, or operation 4.2 to load Patterns and Songs
saved on cassette.
Check that the MIDI cable is not faulty. Also, read the
PRECAUTIONS section of this manual for advice on
electrical
Repeat the Load operation, making sure that the tape
playback level is high. Also, check that the cassette
cable is functioning correctly. If necessary, clean and
demagnetize the tape heads.
Make sure that the cassette you are using contains data
that was just saved. If there is still a problem, save the
data again and, execute the Verify operation once more.
Make sure that the MIDI device connected to the RX17
is transmitting the correct type of data (i.e. RX17 Pattern,
Song and Instrument data).
Make sure that the type of data you are loading is correct
for the RX17, then execute the load operation again.
Press any key to clear the LCD. Send less dense data; or
send data at a slower tempo.
Use operation 4.1 to save the Pattern and Song data to
cassette. Then use operation 2.4 to clear Patterns, or
operation 3.3 to clear Songs, prior to entering new data.
Write two or more shorter Patterns, each of which forms
a section of the Pattern you were trying to write. Then
use operation 3.2 to combine the short Patterns into a
Song.
See if you can enter repeats in the Song to bring it up to
the required length.
1. Enter correct Part numbers.
2. Copy a different group of Parts so that the destination
Part is outside the Parts to be copied.
Enter the correct Part number.
Write a new Pattern at the desired Pattern length.
Press +1 YES to restore the RX17 to normal operation.
Consult your Yamaha dealer about battery replacement.
Press +1 YES to restore the RX17 to normal operation
Consult your Yamaha dealer about battery replacement
as soon as possible.
1. The LCD will next display the empty Part following the
last Part of the Song. Continue the Copy Part operation
to copy to this Part, or enter a new Part number.
2. The LCD will next show the empty Part following the
last Part of the Song. You can now edit from this
point, or select the Search Part function again in the
normal way.
REMEDY
interference.