CrimeStopper RS900 Operating Instructions Manual
Series v
Hide thumbs
Also See for RS900:
- Operating instructions manual (12 pages) ,
- Installation instructions manual (26 pages) ,
- Installation instructions manual (28 pages)
Advertisement
RS900 / RS901 SERIES V
CONGRATULATIONS on your choice of a CoolStart™ Remote Engine Starter by Crimestopper Security Products Inc.
This booklet contains the information necessary for using & maintaining your remote start system. If any questions
arise, contact your installation dealer or Crimestopper Security Products Inc. at (800) 998-6880.
**IMPORTANT NOTES:- RS901 MODEL**
RS901 Model is an add-on/expansion unit, without remotes or an antenna, which must be controlled by an existing
alarm or keyless entry system. Some features including "Infinity Run" feature are not available when using an RS901
system.
TECHNICAL SUPPORT: (800) 998-6880
Monday - Friday 8:00am - 4:30pm Pacific Std. Time
Web Site: www.crimestopper.com
E-mail: email@crimestopper.com
CRIMESTOPPER SECURITY PRODUCTS, INC.
1770 S. TAPO STREET, SIMI VALLEY, CA. 93063
REV B - 9.2002 S/W: 614
OPERATING INSTRUCTIONS
This device complies with FCC Rules part 15. Operation is subject
to the following two conditions: 1) This device may not cause
interference, and (2) this device must accept any interference that
may be received, including interference that may cause undesired
operation. The manufacturer is not responsible for any radio or TV
interference caused by unauthorized modification to this
equipment. Such modification could void the user's authority to
operate the equipment.
Advertisement
Related Manuals for CrimeStopper RS900
Summary of Contents for CrimeStopper RS900
- Page 1 RS900 / RS901 SERIES V CONGRATULATIONS on your choice of a CoolStart™ Remote Engine Starter by Crimestopper Security Products Inc. This booklet contains the information necessary for using & maintaining your remote start system. If any questions arise, contact your installation dealer or Crimestopper Security Products Inc. at (800) 998-6880.
-
Page 2: Table Of Contents
OPERATION CAUTIONS & WARNINGS CRIMESTOPPER SECURITY PRODUCTS, INC. and its VENDORS shall not be liable for any accident resulting from the use of this equipment. This system is designed to be professionally installed into a car or vehicle in which all items, such as parking brake and all associated components, door switches, transmission shift linkage, throttle linkage, and all engine safety features, are in perfect working condition. -
Page 3: Using The Remote Transmitter
USING THE REMOTE TRANSMITTER (RS900) The transmitter supplied with this system has Four (4) buttons / channels. The button configuration is Factory-set and unchangeable. (RS901 model does not include remote transmitters: For add-on / OEM use only) REMOTE ENGINE STARTING - SUCCESSFUL START: 1) Press and release the remote start button. - Page 4 FLASH 1X START THEN SOLID REMOTE ENGINE STARTING - UNSUCCESSFUL START In the event that the engine does not start on the first attempt, the system shuts down for a few seconds, then attempts to restart the engine a 2 and 3 seconds maximum.
- Page 5 IDLE DOWN MODE: This mode allows the unit to take over operation of the parked vehicle while the ignition key is removed and you exit the vehicle. The vehicle is put into a remote running condition before you exit and it will remain running for the programmed run time or until you come back.
- Page 6 START SOLID INFINITY RUN MODE (RS900 IV ONLY) This mode can only be engaged when "Idle Down" is being engaged. Infinity mode allows the vehicle engine to remain running INDEFINITELY after the programmed run time elapses. This mode will allow the vehicle to be left running and unattended without the ignition key in the switch preventing the vehicle from being stolen.
-
Page 7: Remote Engine Control
2) Parking Lights will start flashing, and doors will unlock. 3) Turn Ignition switch OFF, remove key and exit the vehicle. Engine should remain running. 4) The vehicle’s parking lights will flash for the programmed run time of 12, 24, or 36, or 48 minutes and then switch to solid while motor runs indefinitely or until fuel supply runs out. -
Page 8: Convenience And Safety Features
6) The vehicle will Start by itself every 4 hours until driven with key or started via the remote control. S T A R T CONVENIENCE AND SAFETY FEATURES KEYLESS ENTRY (POWER DOOR LOCK CONTROL, Optional) This system enables you to remotely lock and unlock the vehicle’s doors (if equipped with power locks) through the transmitter for safety and convenience. - Page 9 the remote control must still be utilized to operate the Starter disable feature. REMOTE PANIC (When used with Optional HORN HONK) For personal safety this unit now includes a panic feature. To sound the vehicle car horn, press the Lock Button on the remote for more than 2 seconds.
-
Page 10: Transmitter Programming
RED wires near the remote start module. TRANSMITTER PROGRAMMING TRANSMITTER PROGRAMMING: Note: All transmitter codes must be learned at time of programming!! The RS900 allows storage of up to 4 different transmitter codes. 1. Open Hood. -
Page 11: Vehicle Operation
RS900 V The RS-900 V system can be used for 2 car operation. A single RS900V remote can control two independent vehicles with RS900 V systems installed. SETUP: See diagram below on how to switch your remote to car 2 operation. Once you switched your remote to Car 2, then follow the transmitter programming steps AT VEHICLE #2 and learn YOUR remote, along with Car 2’s existing remotes. -
Page 12: Troubleshooting "Before You Call" Section
CAR I / CAR II OPERATION CAR I Slide START CAR II RS 900 V TROUBLESHOOTING: “BEFORE YOU CALL” SECTION UNIT WILL NOT ATTEMPT A START (KEYLESS ENTRY STILL FUNCTIONS NORMALLY): The unit is in Valet mode. Turn Ignition ON, press and hold valet/programming button for 6 seconds then turn key off. Unit is now out of valet mode and should perform a remote start. - Page 13 2. In some cases [commonly Nissan vehicles], an additional “Start” (Cranking) circuit is required for the vehicle to run properly. The RS900 V system includes a wire that can be used for this Starter #2 circuit. Check with your installer for details.