Toshiba TOSVERT VF-P7 Instruction Manual page 210

[11] Jumper frequency
Communi
Title Function
cation No
 0270 Jump frequency #1
0271 Jump frequency band #1

 0272 Jump frequency #2
0273 Jump frequency band #2

0274 Jump frequency #3

0275 Jump frequency band #3

0276 Object of jump frequency process 0: Process amount, 1: Output frequency

[12] Preset speed operation frequency (8- to 15-stage speed)
Communi
Title Function
cation No
0287 Preset-speed #8

 0288 Preset-speed #9
0289 Preset-speed #10

 0290 Preset-speed #11
0291 Preset-speed #12

 0292 Preset-speed #13
0293 Preset-speed #14

 0294 Preset-speed #15
[13] PWM carrier frequency
Communi
Title Function
cation No
 0300 PWM carrier frequency
(*1)Upper limits differ by applicable motor capacity. For details, refer to 6.12.
Carrier frequency is automatically limited to less than 10kHz when operation frequency is more than 130Hz.
[14] Tripless intensification setup (1/2)
Communi
Title Function
cation No
0301 Auto-restart

Regenerative power ride-through
0302

control / Deceleration stop
0303 Retry selection

 0304 Dynamic braking mode selection 0: Disabled, 1: Enabled/overload detection enabled
0305 Over-voltage stall protection

Base frequency voltage #1
0306

(output voltage adjustment)
Adjustment range
0.0∼ [Hz]
0.0∼30.0 [Hz]
0.0∼ [Hz]
0.0∼30.0 [Hz]
0.0∼ [Hz]
0.0∼30.0 [Hz]
Adjustment range
∼ [Hz]
∼ [Hz]
∼ [Hz]
∼ [Hz]
∼ [Hz]
∼ [Hz]
∼ [Hz]
∼ [Hz]
Adjustment range
0.5∼15.0(8.0, 5.0) [kHz] (*1)
Adjustment range
0: Disabled, 1: Enabled(at power failure),
2: Enabled(at ST ON/OFF), 3: Enabled(1+2)
0: OFF, 1: ON, 2:ON(Deceleration stop)
0: Disabled, 1 to 10 times
0: Enabled, 1: Disabled,
2: Enabled (Forced quick deceleration)
0.0∼600.0 [V]
Sensorless vector/vector with sensor (●valid, −:invalid)
Min. unit (panel/ Default Write during
Speed
communication) setting running
control
0.01/0.01 0.0 Enabled ●/●
0.01/0.01 0.0 Enabled
●/●
0.01/0.01 0.0 Enabled ●/●
0.01/0.01 0.0 Enabled
●/●
0.01/0.01 0.0 Enabled
●/●
0.01/0.01 0.0 Enabled
●/●
0 Enabled
− ●/●
Min. unit (panel/ Default Write during
Speed
communication) setting running
control
0.01/0.01 0.0 Enabled
●/●
0.01/0.01 0.0 Enabled ●/●
0.01/0.01 0.0 Enabled
●/●
0.01/0.01 0.0 Enabled ●/●
0.01/0.01 0.0 Enabled
●/●
0.01/0.01 0.0 Enabled ●/●
0.01/0.01 0.0 Enabled
●/●
0.01/0.01 0.0 Enabled ●/●
Min. unit (panel/ Default Write during
Speed
communication) setting running
control
0.1/0.001 See J-28 Disabled ●/●
Min. unit (panel/ Default Write during
Speed
communication) setting running
control
0 Enabled
− ●/●
0 Enabled
− ●/●
0 Enabled
− ●/●
− See J-28 Enabled ●/●
0 Enabled
− ●/●
0.1/0.1 See J-28 Enabled
●/●
Vector control
V/f Reference
Torque Position
Constant section
control control
− − ● 6.10
6.10
− − ●
− − ● 6.10
6.10
− − ●
6.10
− − ●
6.10
− − ●
6.10
− − ●
Vector control
V/f Reference
Torque Position
Constant section
control control
5.14
− − ●
− − ● 5.14
5.14
− − ●
− − ● 5.14
5.14
− − ●
− − ● 5.14
5.14
− − ●
− − ● 5.14
Vector control
V/f Reference
Torque Position
Constant section
control control
●/● −/● ● 6.12
Vector control
V/f Reference
Torque Position
Constant section
control control
6.13.1
●/● −/● ●
6.13.2
−/− −/− ●
6.13.3
●/● −/● ●
●/● −/● ● 6.13.4
6.13.5
●/● −/● ●
6.13.6
●/● −/● ●