Toshiba TOSVERT VF-P7 Instruction Manual page 171

■Table of contact input terminal function settings
Parameter setting
Positive Negative
logic logic
0 1 No assignment function
2 3 F: Forward operation command
4 5 R: Reverse operation command
6 7 ST: Standby (Inverse)
8 9 RES: Reset
10 11 S1: Preset-speed #1
12 13 S2: Preset-speed #2
14 15 S3: Preset-speed #3
16 17 S4: Preset-speed #4
18 19 Jog run
20 21 Emergency stop
22 23 DC injection breaking
Acceleration/deceleration
24 25
switching #1(*2)
Acceleration/deceleration
26 27
switching #2(*2)
28 29 V/f switching #1(*2)
30 31 V/f switching #2(*2)
32 33 Torque limit switching #1(*2)
34 35 Torque limit switching #2(*2)
36 37 PID control OFF selection
38 39 Pattern group #1
40 41 Pattern group #2
42 43 Pattern group #3
44 45 Pattern group #4
46 47 Pattern run continuation signal
48 49 Pattern run trigger signal
50 51 Forced Jog forward operation
52 53 Forced Jog reverse operation
54 55 Reservation area(*3)
56 57 Reservation area(*3)
58 59 Reservation area(*3)
60 61 Reservation area(*3)
62 63 Reservation area(*3)
64 65 Reservation area(*3)
66 67 Reservation area(*3)
68 69 Reservation area(*3)
(*1): Valid when (Speed setting mode selection) is set at (Up-down frequency).
The frequency setting range is between 0.0 to (Upper limit frequency).
In this case, acceleration time is (Acceleration time #2), and deceleration time is
(Deceleration time #2).
(*2): To switch acceleration/deceleration pattern, V/f pattern, torque limit #1∼#4, give the
following signals to switching functions. (in case of positive logic)
Acc/dec, V/f, torque limit #1
Acc/dec, V/f, torque limit #2
Acc/dec, V/f, torque limit #3
Acc/dec, V/f, torque limit #4
(*3): Reservation area. Do not set at these functions.
■Sink logic/source logic
Switching between sink logic and source logic (input/output terminal logic) is possible.
For details, refer to the section 2.3.2.
Parameter setting
Function
Positive
logic
70
72
74
76
78
80
82
84
86
88
90
92
94
96
98
100
102
104
106
108
110
112
114
116
118
120
122
124
126
128
130
132
134
switching #1
OFF
ON
OFF
ON
G-4
Function
Negative
logic
71 Reservation area(*3)
73 Reservation area(*3)
75 Reservation area(*3)
77 Reservation area(*3)
79 Reservation area(*3)
81 Reservation area(*3)
83 Reservation area(*3)
85 Reservation area(*3)
87 Binary data write
89 Up/down frequency (up) (*1)
91 Up/down frequency (down) (*1)
93 Up/down frequency (clear)
95 PUSH-type run command
97 PUSH-type stop command
99 Forward/reverse selection
101 Run/stop command
103 Commercial power/INV switching
Frequency reference priority
105
switching
107 VI/II terminal priority
109 Command terminal board priority
111 Parameter editing enabling
Control switching (torque,
113
position)
115 Deviation counter clear
117 Position control forward limit LS
119 Position control reverse limit LS
Light load high-speed operation
121
enabling
123 Reservation area(*3)
125 Preliminary excitation
System consistent sequence
127
(BC: Braking command)
System-supporting sequence
129
(B: Brake release)
System-supporting sequence
131
(BA: Brake answer)
System-supporting sequence
133
(BT: Brake test)
135 Reservation area(*3)
switching #2
OFF
OFF
ON
ON