Sign in today to find solutions:

Forgot your password?

Don't have an account? Sign up

 
CONTENTS

Summary of Contents

  • Page 1

    CONTENTS...

  • Page 2

    IMPORTANT SAFETY INSTRUCTIONS FCC STATEMENT...

  • Page 3

    IMPORTANT SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS...

  • Page 4

    IMPORTANT SAFETY INSTRUCTIONS ANTENNA L E A D I N WIRE GROUND CLAMP ANTENNA DISCHARGE UNT (NEC SECTION 810-20) GROUNDING CONDUCTORS (NEC SECTION 810-21) GROUND CLAMPS POWER SERVICE GROUNDING ELECTRODE SYSTEM NEC-NATIONAL ELECTRICAL CODE (NECART 250, PARTH) IMPORTANT SAFETY INSTRUCTIONS...

  • Page 5

    IMPORTANT SAFETY INSTRUCTIONS the left and right side 1. Insert the DC plug on supplied AC/DC adaptor to the DC IN Jack on the Right side of TV. 2. Insert the AC/DC adaptor into a conveniently located AC outlet having AC~ 100-240V, 50/60Hz in Vertical or Horizontal directions. (Never insert the AC/DC Adaptor the outlet on ceiling.) level AC/DC Adapter...

  • Page 6

    ANTENNA CONNECTIONS CABLE CONNECTIONS...

  • Page 7

    CABLE CONNECTIONS the signal type in setting menu CABLE CONNECTIONS CONNECTION USING HDMI (CABLE NOT INCLUDED): 1. Connect the HDMI cable (not included) from the HDMI of the TV to the HDMI of external unit as the figure below. 2. Set the SOURCE of the TV to HDMI mode. CONNECTION USING AUDIO/VIDEO JACKS (CABLES NOT INCLUDED): Audio In HDMI...

  • Page 8

    CABLE CONNECTIONS Video In L-Audio In-R Phones PC (Personal Computer) PC-Audio In CABLE CONNECTIONS Using component video connection cables (not included) to external device's Y/Pb/Pr output jacks to the Y/Pb/Pr jacks on the TV. 2. Connect the left and right audio connection cable from the external unit's AUDIO OUTPUT jacks to the Audio In jacks on the TV.

  • Page 9

    LOCATION OF CONTROLS 1. VOL- (Volume down) button 2. VOL+ (Volume up) button 3. CH- (Channel down) button 4. CH+ (Channel up) button 5. MENU button 6. SOURCE button 7. POWER button HDMI 8. DC IN jack 9. HDMI Port 10.

  • Page 10

    LOCATION OF CONTROLS CC: Press repeatedly to turn CCD (Closed Caption) On/Off. INFO: Press to display the information; settings and the status of current mode on the screen. PICTURE: Press repeatedly to select the preset picture modes. COLOR BUTTONS: Reserved using in Teletext and interaction ATSC (Digital TV) mode as the on screen instructions.

  • Page 11

    BASIC OPERATION top of TV or remote control TV (Green LED indicator will light). Press again to power OFF (Standby) the TV (Red LED indicator will light). CHANNEL SETTING CH + or CH - control, a few seconds later, the selected channel will apper on screen.

  • Page 12

    THE ON-SCREEN MENU SETTING Menus Press the MENU button to enter to the setting menu (press again to exit). Navigator Press the button to select and highlight the function within the menu you want to adjust. Press the (enter) button to go to the sub-menu to confirm the selection.

  • Page 13

    THE ON-SCREEN MENU THE ON-SCREEN MENU PC VGA SETTINGS Menu Operation in VGA mode only In VGA mode. Enter to the PC settings menu as previously procedures. The PC SETTINGS menu will appear on the screen and Auto Adjust will be highlighted. Press and hold the (enter) button one second then release the button.

  • Page 14

    THE ON-SCREEN MENU Channel List Menu Enter to the channel setting menu as previously procedures, the CHANNEL setting menu will appear on the screen and Channel List will be highlighted. Press the (enter) button, the channel list of the stored channels will appear on the screen. Press the Navigator button to select the desired channel then press the...

  • Page 15

    THE ON-SCREEN MENU CHANGE PASSWORD Menu If Change Password is selected, press (enter) button to enter. The CHANGE PASSWORD menu will appear and Old PIN will be highlight. Enter the preset 4 digit passwords (or the super password 1506 ) by pressing the numeric buttons.

  • Page 16

    THE ON-SCREEN MENU RETRACTABLE STAND Notes: Enter to others setting menu as previously procedures, the OTHERS menu will 1. The 15 for backward and 5 for foreward appear on the screen and ATV blue Back will be highlighted. Press the (enter) to turn it On (If no signal received, background of screen will turn to Blue) or Off.

  • Page 17

    TROUBLESHOOTING Check and make sure the Video output from the connected device is set to HD (High Definition) and the Audio output is set to PMC (Plus Code Modulation). For details, refer to the Instruction Manual of the connected device. The TV turn off No Operation Power Off was set to on, when no any buttons on the TV/remote control was...

  • Page 18

    LIMITED WARRANTY CLC501_IB E0CR2_B0CV...

Comments to this Manuals

Symbols: 0

Latest comments:

×

Select the desired size and copy embed code

Copy your embed code and put on your site: