Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Craftsman 536.88521
Summary of Contents for Craftsman 536.88521
- Page 1 5.0 Horsepower 21 Inch Single Stage Auger Propelled SNOW THROWER Electric Start MODEL NO. 536.885210 Caution: Read and follow all Safety Rules and Operating Instructions before first use of this product, SEARS, ROEBUCK AND CO., Hoffman Estates, IL 60179 U.S.A. 761893 07/27/98...
- Page 2 For two years from the date of purchase, tained, lubricated, and tuned up according to the operating and maintenance instruc- tions in the owner's manual, Craftsman will repair, free of charge, any defect in mate- rial or workmanship. If this Craftsman Snow Thrower is used for commercial or rental purposes, this war- ranty applies for only 90 days from the date of purchase.
-
Page 3: Fuel Safety
• Use only attachments and accessories approved by the manufacturer of the snow thrower (such as e|ectric starter kits, etc.). • Never operate the Snow thrower without good visibility or light. Always be sure of your footing, and keep a firm hold on the handles. - Page 4 (Section 4442 of the Califor- nia Public Resources Code). Other states may have similar laws. Federal laws apply on federal lands. A spark arresterimuffler available through your nearest Craftsman Authorized Service Center (See ENGINE and when REPAIR PARTS section in this manual).
-
Page 5: Assembly
CAUTION" Always wear safety glasses or eye shields while assembling snow thrower. TOOLS REQUIRED FOR ASSEMBLY 1 - Knife to cut carton The figure to the right shows the snow thrower completely assembled. References to the right or left hand side of the snow thrower are from the viewpoint of the operator's position behind the unit. -
Page 6: Snow Thrower Overview
KNOW YOUR SNOW THROWER READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING SNOW THROWER. Compare the illustrations yourself with the location of various controls and adjustments. Save this manual for future reference. Etecric Ignition Off Ignition On Start Auger Control Chute Control Lower Handle Chute Deflector... -
Page 7: How To Use
TO USE YOUR SNOW THROWER TO STOP YOUR SNOW THROWER • To stop the auger, release the auger control bar. NOTE: If the auger continues to creep, refer (To Adjust Auger Control Cable paragraph on page 11). • To stop the engine, turn key to the OFF position. -
Page 8: Gasoline And Oil Mixture
DO NOT FILL THE FUEL TANK WITH GASOLINE Shake Can (1/2 cup or 3.2 oz.) 1 U,S. gallon container GASOLINE AND OIL MIXTURE Mix gasoline and oil as follows: • Pour I U.S. quart of fresh, clean, unleaded automotive gasoline to a gallon gasoline container. -
Page 9: Warm Start
• As engine warms up and begins to operate evenly, move the choke control slowly to the OFF position. If the engine falters, turn to 1/2 choke until it runs smoothly, then move to OFF position. NOTE: Allow the engine.to warm up for a few minutes before using snow thrower, as the engine will not develop full power until it reaches operating... -
Page 10: Specifications
SNOW THROWING TIPS • This snow thrower will propel itself forward when the handle is raised enough to cause the auger blades to contact the ground. The auger should stop when auger control bar is released, If it does not, refer to Adjust Auger Control Cable paragraph on page 12. -
Page 11: Maintenance
CUSTOMER RESPONSIBILITIES SERVICE RECORDS Fill in dates as Before Each you complete regular service Tighten All Screws & Nuts Check Spark Plug Check Drive Belts Lubricate Chute Control Flange Check Fuel v" Drain Fuel GENERAL RECOMMENDATIONS The warranty on this snow thrower does not cover items that have been subjected to op- erator abuse or negligence. -
Page 12: Top Cover
If you think the engine governor high speed needs adjusting, contact your nearest Craftsman service center who has the proper equipment and experience to make any unnecessary adjustments. TO ADJUST... -
Page 13: Belt Cover
• Remove the gas cap. • Remove the two bolts and nuts from the front lip of the top cover. Use a flat head screwdriver and a 3/8" wrench. See figure c,n this page. • Remove the Idolt from the front right side. Use a 5/16"... - Page 14 The drive belt on this unit is of special construction and must be replaced with the same type belt available at your nearest Craftsman Service Center. • Remove the belt cover. See to Remove the Belt Cover paragraph on page 13.
- Page 15 If you believe that the engine is running too fast or too slow, take your snow thrower to your nearest Craftsman Service Center for repair and adjustment. plug.
-
Page 16: Engine Storage
Carbu Drain I! you do not want to remove gasoline, a fuel stabilizer (such as Craftsman stabilizer No. 33500) may be added to any gasotine left in the tank to minimize gum deposits and acids. If the tank is... -
Page 17: Troubleshooting
Stop engine immediately and impeller turn key to OFF position and re- move key. Tighten all bolts and make all necessary bration continues, serviced by a Craftsman repairman Repair or replace auger assem- Replace drive belt of auger con- Adjust auger control cable... - Page 18 CRAFTSMAN ELECTRIC START ASSEMBLY Nots: Always use original equipment parts. Use of service/replacement parts other than original parts may void your warranty. REF. PART NO. 57569 =311633 414106 271163 56023 761893 21" - 5H.P. SNOW THROWER 536.885210 All unnumbered items are...
- Page 19 ORAFTSMAN ENGINE/DRIVE ASSEMBLY REF_ PART NO. PART NAME ENGINE Engine, Model 143.995071 (See Engine pages) 180077 Screw, 5/16-18x.75 120638 Washer, Hvsptlk 333970 Pad, Brake 180077 Screw, 5/16-18x.75 120638 Washer, Hvsptlk 579052 Screw, 1/4-20x.63 73826 Nut, 1/4-20 Reghexctrlk 334079 Guide, Belt 71071 Washer, Flat.349x.69x.066 120638...
-
Page 20: Discharge Chute Assembly
CRAFTSMAN 21" - 5H.P. SNOW THROWER FRAME ASSEMBLY DISCHARGE CHUTE ASSEMBLY -601 592-, 583- "_?' • ... •.._1_, 536.885210 REF. PART NO. PART NAME 333769-853 Frame, Side RH 333767 Frame, Side LH 333987 Channel, 180044 Screw, 1/4-20x2.00... - Page 21 CRAFTSMAN BELT COVER ASSEMBLY REF, PART NO. PART NAME 340097 Cover, Bottom 313685 Screw, 1/4-14x.75 761538 Panel, Spark Plug Access 578109 Nut, 1/4-10 Speed J Type 761539-853 Panel, Control 313674 Screw, 1/4-20xl .25 71067 Washer, Flat.281x.63x.065 782585 Nut, 1/4-20 Reghexctrlk 57587 Grommet &...
- Page 22 CRAFTSMAN 21" - 5H.P. SNOW THROWER AUGER HOUSING ASSEMBLY 511512 483--_ 520"10 520-8 REF. PART NO. 340091 302628 71067 73826 55323 577707 302628 _.93 302635 :51o 577023 710263 71067 302635 327072 520-2 302565 _20-6 49838 _20-8 335992 _20-10 307049-853 580251...
-
Page 23: Handle Assembly
CRAFTSMAN iiIIIII " REF. PART NO. PARTNAME 313449 Cable, Upper Control 11.95 ] 13441 Brkt, Cable Adjust 313448 Cable, Lower Control 16.00 308146 Boot, Clutch Spring 313471 Spdng, Extension 333909-853 Lower Handle 313674 Screw 1/4-20xl .25 71067 Washer, Flat .281x.63x.065 21"... - Page 24 CRAFTSMAN CHUTECONTROL REF. PART NO. PART NAME 337941 Chute Rod Assembly 71072 Washer, Flat .406x.81x.066 71082 Cotter Pin .094xl .00 313431 Washer, Curved Spring 335264 Chute Crank Brkt Assy 71072 Washer, Flat .406x.81x.066 57082 Knob, Sleeve 331532 Nut. Push 3809 Bolt 1/4-20x.63 Cart.
- Page 25 CRAFTSMAN 2-CYCLE ENGINE MODEL NUMBER 143.995071 1_._.135...
- Page 26 CRAFTSMAN 2-CYCLE ENGINE REF, PART# PARTNAME 250296A CYLINDER (INCL. 75A,105,106,&138) GOVERNOR LEVER 490317 GOVERNOR LEVER 490304 EXTENSION SPRING 33374 THROTTLE LINK 490318 SPRING OIL SEAL 510340 570673 BALL BEARING 510338 SLIDE RING 530158 BALL BEARING 530161 BALL BEARING 530159 BEARING RETAINER...
- Page 27 CARBURETOR NO. 640088 PART NAME REF. PART# 632538 THROTTLE SHAFT & LEVER ASSY 631621 THROTTLE SHUTTER 650506 THROTTLE & CHOKE SHUTTER SCREW 632734 CHOKE SHAFT & LEVER ASSY 631815 CHOKE SHUTTER 630735 CHOKE POSITIONING 632164 FUEL FITTING 631951 FLOAT BOWL ASSY (INCL.
- Page 28 STARTER NO. 590743 REF. PART# 590743 590740 590616 590617 590645A 590643 590535 590701 590741 a -7 PART NAME STARTER, REWIND RETAINER • DOG STARTER SPRNG, PULLEY & REWIND SPRING ASSY HOUSING ASSY, STARTER ROPE, STARTER (LENGTH 98"& 9/64"DIA.) HANDLE, STARTER LOCKING TAB...
- Page 29 ELECTRIC STARTER NO. 590670 REF. PART# 34952 590608 34953 590644 34949A 590654 34950 34951 34955 590674 590675 590676 590677 590659 590587 590660 590661 590662 33450 590663A 32450B 30063 650819 650742 730623 PART NAME RETAINER RING DUST WASHER PINION DRIVER ANTI-DRIFT SPRING GEAR ANTI-DRIFT...
- Page 30 For the repair or replacement need delivered directly to your home Call 7 am-7 pm, 7 days a week 1-800-366-PART (1-800-366-7278) Para ordenar piezas con entrega a domicilio -1-800-659-7084 For in-house major brand repair service Call 24 hours a day, 7 days a week 1-800-4-REPAIR (1-800-473-7247) Para pedir servicio de reparaci6n a...