USER GUIDE Contents Overview ...2 Getting Started...2 Unpacking myPower ALL ...2 Getting to Know myPower ALL ...3 Charging myPower ALL ...3 Using myPower ALL ...4 Select/Connect the Adapter Plug ...4 Connect the Power Output Cord...5 Adjust the Voltage Level ...5 Connect the Portable Device ...8 View myPower ALL Battery Capacity ...8 Recording Device Information ...9...
Overview You can use myPower™ ALL—the universal rechargeable battery—to power just about any portable device. Simply connect myPower ALL to your portable DVD player, notebook computer, digital camera, digital camcorder, portable CD player, PDA, mobile phone, or other portable device to extend the battery life.
Getting to Know myPower ALL Voltage Indicators/ Capacity Indicators Voltage Lock Charging myPower ALL myPower ALL will charge in four hours when completely empty. The green CHARGE indicator will turn on after the battery is 80% charged. Therefore, you should view the actual battery capacity before disconnecting the power adapter to stop charging.
2. Locate the polarity symbol on your device in the area around the power connector jack: Center Positive myPower ALL supports Center Positive polarity only. If your device has a Center Negative polarity, do not power the device with myPower ALL; contact support@tekkeon.com for assistance. Center Negative...
1. Plug the large end of the power output cord into the DC OUT jack on the end of myPower ALL. The 3V (MP3300) or 5V (MP3400) voltage indicator will turn on to indicate that the voltage is set to the lowest setting.
Page 8
To do this, press the voltage selector until the voltage indicator turns on under the appropriate voltage selection (3, 4.5, 5, 6, 7.5, 9, 12, 14 for MP3300 and 5, 6, 7.5, 9, 12, 14, 16, 19 for MP3400). For example, if your device requires 6V, set the voltage to 6. If your device requires 7.2V, set the voltage to 7.5.
(Watt=Voltage x Amps). If the output power is greater than 64W, myPower ALL will not power or charge the device. If it is less than 64W, set the voltage on MP3300 to 12V and test to see if it will power your notebook at this setting.
Connect the Portable Device 1. Connect the adapter plug into the power jack on the portable device. 2. Turn on the portable device and use it as you would normally. While connected, myPower ALL will power and charge your device. (As mentioned earlier, myPower ALL will not charge a device if the voltage setting is lower than that required.) Leave the portable device turned off and myPower ALL will charge the device battery.
You can obtain most adapters through the web site, or by contacting Tekkeon by phone at 888-787-5888 or 1-714-832-1266. If available through Tekkeon, the adapter will be sent to you for a nominal fee.
ALL, the device will shut down when turned on and cannot be powered and/or charged by myPower ALL. 2. Verify that the device does not require more than 14V (MP3300) or 19V (MP3400). If the device requires more, MP3300/MP3400 will not be able to charge the device. However, in most but not all cases, MP3300/MP3400 will be able to power the device.
The product enclosed herein is warranted to be free of operational defects for a period of one year from the date of purchase. In the event of a defect in operation during the warranty period Tekkeon, Inc. will replace the defective product when the owner returns all product contents. The limited warranty will be considered void if the unit is tampered with, subject to misuse, negligence or accidental damage, has been improperly serviced, or if the security seal is removed.
Customer support for myPower ALL is available at: Tekkeon, Inc. c/o myPower ALL 3002 Dow Avenue, #134 Tustin, CA 92780 888-787-5888 / 714-832-1266 www.tekkeon.com Tekkeon, Inc. must issue a Return Merchandise Authorization (RMA) number for all exchanges or refunds. www.tekkeon.com...