Problems Related To Copying Operation - Sharp MX-4100N Operation Manual

COPYING

PROBLEMS RELATED TO COPYING OPERATION

• Copying does not take place. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-16
• Auto selection of the color mode does not take place. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-16
• Image rotation does not take place. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-17
• Two-sided copying does not take place.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-17
• The paper size of a tray cannot be set.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-17
PROBLEMS RELATED TO COPY RESULTS
• The image is too light or too dark.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-18
• Colors are off. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-18
• Part of the image is cut off. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-18
• Copies come out blank. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-18
• If you cannot find the item that you are looking for in the above table of contents, see
8-39).
• If you are unable to solve a problem using the solutions in this manual, switch off the [POWER] key (
main power switch. Wait at least 10 seconds, and then switch on the main power switch and the [POWER] key (
in that order.
When the LINE indicator is lit or the DATA indicator is lit or blinking, do not switch off the main power switch or unplug
the power plug. This may damage the hard drive or cause the data being stored or received to be lost.
PROBLEMS RELATED TO COPYING OPERATION
Problem
Copying does not take
place.
Auto selection of the
color mode does not
take place.
Point to check
Have functions been disabled by the
administrator?
Are you using one of the following types
of originals?
Black & White is not selected
• Are there colors or coloring in the
paper?
Color is not selected
• The color in the original is very light.
• The color in the original is very dark,
almost black.
• Is only a very small area of the
original colored?
When user authentication is enabled, the functions that
you can use may be restricted in your user settings.
Check with your administrator.
When the color mode is set to "Auto", the machine
detects whether the original is black and white or color
when the [COLOR START] key is pressed. However,
when an original similar to one of those at left is used,
automatic detection may not give the correct result. In
this event, specify the color mode manually.
8-16
TROUBLESHOOTING
"GENERAL PROBLEMS" (page
) and the
Solution
Contents
)