Sony SSC-CD75 Operating Instructions

3-113-376-02 (1)
Color Video Camera
Operating Instructions
Before operating the unit, please read this manual thoroughly and
retain it for future reference.
SSC-CD75/CD75P
SSC-CD77/CD77P
 2007 Sony Corporation
Printed in China
English
Owner's Record
The model and serial numbers are located on the bottom. Record these
numbers in the spaces provided below.
Refer to these numbers whenever you call upon your Sony dealer
regarding this product.
Model No. Serial No.
WARNING
To avoid electrical shock, do not open the cabinet. Refer
servicing to qualified personnel only.
WARNING
This installation should be made by a qualified service person and should
conform to all local codes.
WARNING
A readily accessible disconnect device shall be incorporated in the
building installation wiring.
WARNING (for Installers only)
Instructions for installing the equipment on the ceiling or the wall:
After the installation, ensure the connection is capable of supporting four
times the weight of the equipment downwards.
CAUTION
The rating label is located on the bottom.
Power Supply
Caution for U.S.A. and Canada
The SSC-CD75/CD77 operates on 24V AC or 12V DC.
The SSC-CD75/CD77 automatically detects the power.
Use a Class 2 power supply which is UL Listed (in the U.S.A) or CSA-
certified (in Canada).
Caution for other countries
The SSC-CD75/75P/CD77/77P operates on 24V AC or 12V DC.
The SSC-CD75/75P/CD77/77P automatically detects the power.
CAUTION
After incorporating the heater unit, the rated power of the camera will be
16 W.
Ensure the power source is capable of providing the total power.
For customers in the U.S.A.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the
interference at his own expense.
You are cautioned that any changes or modifications not expressly approved
in this manual could void your authority to operate this equipment.
All interface cables used to connect peripherals must be shielded in order
to comply with the limits for a digital device pursuant to Subpart B of Part
15 of FCC Rules.
For Customers in Canada
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003
du Canada.
For Customers in Eurpoe
The manufacturer of this product is Sony Corporation, 1-7-1 Konan,
Minato-ku Tokyo, Japan.
The Authorized Representative for EMC and product safety is Sony
Deutschland GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Germany.
For any service or guarantee matters please refer to the addresses given
in separate service or guarantee documents.
For customers in other countries
WARNING
This is a Class A product. In a domestic environment, this product may
cause radio interference in which case the user may be required to take
adequate measures.
In the case that interference should occur, consult your nearest
authorized Sony service facility.
This apparatus shall not be used in the residential area.
ATTENTION
The electromagnetic fields at specific frequencies may influence the
picture of the unit.
Features
This is a dome-shaped color video camera for which the 1/3 type Super
® ®
HAD CCD (SSC-CD75/CD75P) or SuperExwave (SSC-CD77/CD77P)
has been adopted. It has the following features:
• IP 66* sealed enclosure (sturdy and weatherproof structure) suitable for
outdoor installation
• Manual setting of the camera direction – panning, tilting and rotating
• Vari-focal auto iris lens as standard equipment. The focal length of the
lens is from 2.8 mm to 10 mm.
• High quality CCD and clear dome cover enable high sensitivity.
• Backlight compensation through the center measurement.
• Automatic white balance tracking and adjustment (ATW/ATW-PRO)
• 24 V AC / 12 V DC power supply system
• Line lock function (24 V AC)
• Day/Night function automatically switches between color and
monochrome modes. You can control this function through an external
source when connecting the supplied DN cable. (SSC-CD77/CD77P)
• YT-HU75 Heater Unit (optional) allows you to operate this unit in low
temperature environments down to –40 °C (–40 °F). (24 V AC only /
except cold starting)
• Super HAD CCD ® is a registered trademark of Sony Corporation.
• Super Exwave ® is a registered trademark of Sony Corporation.
* IP66 is a protection grade provided under JIS and IEC.
Notes on Use
Operating or storage location
Do not shoot an extremely bright object (an illumination, the sun, etc.).
Also, avoid operating or storing the camera in the following locations, as
these can be a cause of a malfunction.
• Extremely hot or cold places (Operating temperature: –20 °C to
+50 °C [–4 °F to 122 °F])
• Close to heating equipment (e.g., near heaters)
• Close to sources of strong magnetism
• Close to sources of powerful electromagnetic radiation, such as radios
or TV transmitters
• Locations subject to vibration or shock
• Dusty locations
• Locations under the influence of fluorescent light or reflection of a
window
• Under an unsteady light (the image will flicker.)
Ventilation
To prevent heat buildup, do not block air circulation around the camera.
Transportation
When transporting the camera, repack it as originally packed at the
factory or in materials of equal quality.
Cleaning
• Use a blower to remove dust from the lens.
• Use a soft, dry cloth to clean the external surfaces of the camera.
Stubborn stains can be removed using a soft cloth dampened with a
small quantity of detergent solution, then wipe dry.
• Do not use volatile solvents such as alcohol, benzene or thinners as
they may damage the surface finishes.
To install the camera outdoors
Attach the dome casing securely to the unit casing.
Make sure you seal the locations listed below with sealant (e.g. silicon
sealant) to prevent moisture from getting inside the casing.
– Camera installation holes (4)
– Conduit holes (side/bottom)
Note on laser beams
Laser beams may damage a CCD. You are cautioned that the surface of a
CCD should not be exposed to laser beam radiation in an environment
where a laser beam device is used.
Location and Function of Part
The figure shows the camera without the dome casing and slit cover.
Side
1 24V AC/12V DC (power input) cable
Connect to a 24V AC or 12V DC power supply system ( ). The
connector tip is a quick-disconnect type. You can screw the cables in
the tip.
2 BNC cable
Outputs a composite video signal. Connect to a composite video input
connector of a video monitor, VCR, etc ( ).
3 Conduit holes (3/4 inch)
Connect a pipe to this hole. There are two conduit holes on the unit
casing, one on the side and one at the bottom. The cover plug is
installed in the side conduit hole at the factory. Remove the plug as
needed and connect the pipe to the hole.
4 Camera head holder
5 Lens
6 Lens ring fixing screw
Loosen this screw before adjusting the zoom and focus, then tighten it
to fix the lens position. The screw can be inserted at one of three
points.
7 Zoom ring
Turn this ring to adjust the field of view.
8 Focus ring
Turn this ring to adjust the focus.
Inside
9 Heater unit connector
Connect the cable of the optional YT-HU75 Heater Unit.
0 Camera head fixing screw
First loose the screw and face the camera head to the desired
direction, then tighten the screw to fix it.
qa MONITOR out jack
Connect to a video input connector of a monitor. You can adjust the
camera while looking at the image on the monitor. After adjusting the
camera, disconnect the cable.
qs V PHASE (vertical phase) adjustment screw
Use this screw to adjust the vertical phase of cameras synchronized
by LL.
qd Mode setting DIP switch
Upper
Lower
Position
No. Switch
Upper (ON) Lower
1 INT/LL LL INT
2 AGC ON OFF
3 BLC ON OFF
4 WHT ATW Pro ATW
5 Day/Night AUTO MANUAL
6 Day/Night Time SHORT LONG
7 Day/Night Level HIGH LOW
1: INT/LL (line lock) switch (Initial setting: LL)
Use this switch to set the camera synchronization mode to INT
(internal) or LL (line lock, Only when the power is AC 24 V).
2: AGC (automatic gain control) switch (Initial setting: ON)
Set to ON to adjust the gain of the video amplifier automatically
according to the brightness of the object.
3: BLC (backlight compensation) switch (Initial setting: OFF)
Use this switch to adjust the exposure to compensate for situations
where the subject is lit from behind.
Notes
When BLC switch is set to ON, a hunting may be generated due to a
picture. In this case, set BLC switch to OFF.
4: ATW switch (Initial setting: ATW)
ATW: Automatic adjusting function of the white balance, effective for
use under special light like a sodium lamp.
ATW Pro: Automatic adjusting function of the white balance according
to the color temperature based on a fluorescent light, incandescent
lighting, or natural light.
5: Day/Night switch (Initial setting: MANUAL) (SSC-CD77/CD77P
only)
AUTO: Switches color and black-and-white automatically. (Set AGC
also to ON.)
MANUAL: Switches "IN" terminal between color (H (+5V) or open) and
black-and-white (L (0V)) when the DN cable (supplied) is connected.
6: Day/Night Time switch (Initial setting: LONG) (SSC-CD77/CD77P
only)
Sets the time for switching Day and Night mode.
SHORT takes more than 2 seconds, and LONG takes more than 30
seconds.
7: Day/Night Level switch (Initial setting: LOW) (SSC-CD77/CD77P
only)
Sets the brightness of the object of when Day and Night mode
switches.
LOW is approximately 1 lux and HIGH is approximately 5 lux.
A
1
2
4
5
qf Cable clamp
Secure the BNC cable and AC 24V / DC 12V cable with this clamp.
Curl the cable clamp upward from inner side to fix the cables (C).
qg D/N cable connector (SSC-CD77/CD77P only)
Connect the supplied D/N (Day/Night) cable to this connecter.
When the D/N cable is connected, you can switch Day and Night
modes from outside.
The wires of the cable control the following signals.
Red wire: Day/Night In
When the "6" of Mode setting DIP switch is set to "Manual";
- Color: Open or H (+5 V)
- Black and White: L
Black wire: GND
White wire: Day/Night Out
- Color: H (+5 V)
- Black and White: L (0 V)
qh AC / DC IN (power input) connector
Connect an AC 24V / DC 12V cable to this connector.
qj VIDEO OUT (Video out) connector
Connect the BNC cable to this connector.
qk Unit casing
The unit casing is made of die-cast aluminum and has conduit holes
on the side and at the bottom.
ql Camera installation holes (4 positions)
Make sure to tighten the screws securely when installing the camera.
w; Safety cord
This cord prevents the dome casing from falling off the unit casing.
Make sure that the cord does not get caught between the dome casing
and the unit casing. Rotate the cord and adjust the position of the cord.
wa Dome casing
The dome cover is made of polycarbonate. A waterproof rubber gasket
is provided on the joint surface to the unit casing.
(continued on the reverse side)
A
B
B
9 0 qa qs qd qf qg qh qj
3
6
7
8
w; wa
C