Download Print this page

Cornelius Hoshizaki KM250 Installation Instructions

Cornelius ice maker installation instruction

Advertisement

Quick Links

INSTALLATION INSTRUCTIONS

These "K" style kits apply to the following ice makers and are for use with DF/ED 200/250 dispensers:
Hoshizaki KM250/450/500/630/650
Item No.
Part No.
1
630000310
2
15303
3
50904
4
630000311
5
70217
6
90221
7
70188
8
630460040
9
22127
!
WARNING:
Disconnect power to the unit before installing the adaptor following all lockout/tag out procedures established by the
user. Verify that all the power is off to the unit before performing any work.
Failure to comply could result in serious injury, death or damage to the equipment.
!
WARNING:
All ice baffle plates and bin stats, if included or recommended in this kit, must be installed as directed in this manual or
the equipment manufacturer's instructions.
Failure to comply could result in serious injury, death or damage to the equipment.
!
WARNING:
All of the attachment screws and plates must be installed as directed in this manual.
Failure to comply could result in serious injury, death or damage to the equipment.
1. Set Ice maker lid on the top of the dispenser and position it flush with the back and sides of the dispenser.
2. Using the slotted holes in the lid as a template, drill four (4) 0.140" diameter holes at the bottom of the slots (see
Detail A, Figure 1). Use extreme care not to drill into the hopper. Fasten the lid to the dispenser with four (4) #8
sheet metal screws, two on each side.
3. Seal the ice maker to the top of the dispenser as follows:
A. Apply beads of RTV around the opening in the lid and inside the perimeter of the ice maker outline so
that the ice maker will set on the RTV.
B. Set the ice maker onto the lid and position it as required.
C. Wipe away any excess RTV.
4. Remove the two rear screws (only) installed in step 2. Use those screws to install the mounting brackets (item 2
and/or item 9). Drill 9/64I diameter holes into the ice maker cabinet using the bracket as a template. Use extreme
caution not to drill into any ice maker components (condenser, tubing, etc.). Secure the brackets using the screws
provided.
Release Date: November 14, 2010
© 1997-2010, IMI Cornelius Inc.
"K" S
L
K
TYLE
ID
Table 1. Applicable Models
Ice Maker
Table 2. Loose Shipped Parts
Lid Assembly, "K" Style
Bracket
RTV, Clear, 732, 3 oz. Tube
Cover, RH Assembly
#8 Sheet Metal Screw
Disconnect Before Cleaning
Label,
Thumb Screw #8-32 x 1/2"
Installation Instruction
Bracket, LS Mounting
www.cornelius.com
"K" Style Lid Kit Installation Instructions
, P/N 630000085
IT
Name
- 1 -
Size
22"
Qty.
1
1
1
1
6
1
1
1
1
Revision: B
Publication Number: 630460040

Advertisement

loading

Summary of Contents for Cornelius Hoshizaki KM250

  • Page 1: Installation Instructions

    Failure to comply could result in serious injury, death or damage to the equipment. 1. Set Ice maker lid on the top of the dispenser and position it flush with the back and sides of the dispenser. 2. Using the slotted holes in the lid as a template, drill four (4) 0.140” diameter holes at the bottom of the slots (see Detail A, Figure 1).
  • Page 2 “K” Style Lid Kit Installation Instructions 5. Follow the ice maker manufacturers instruction to complete the installation of the ice maker including the bin ther- mostat if so equipped or required. Note: Bin thermostat must not interfere with agitator rotation.

This manual is also suitable for:

Hoshizaki km450Hoshizaki km500Hoshizaki km630Hoshizaki km650