Sharp XE-A101 Quick Start Manual

XE-A101 Quick Start Guide
The following describes how to get your cash register ready to operate. Follow these steps when you use the cash register for the first time.
1 2
Initializing the Cash
Register
To ensure the cash register operates Install batteries for back-up of sales data
properly, initialize it using the following and programmed contents.
procedure:
1. Push the printer cover forward and
1. Set the mode switch to the REG
position with the power cable
unplugged.
VOID
OFF X/F
REG
Z/PGM
2. Open the battery cover next to the
2. Insert the plug of the power cable
into the AC outlet.
IMPORTANT
This operation must be performed
without batteries loaded.
3. Insert three new "AA" batteries.
The buzzer will sound three times.
3. Now the cash register has been
initialized. The register display will
show "0.00" with "l" .
4. When the batteries are properly installed,
The following are supplied with your
cash register.
IMPORTANT
Improper use of batteries may damage
1 paper roll
the cash register. Please take the
following precautions.
2 drawer lock keys
•Be sure that the positive (+) and negative
1 instruction manual (English)
(-) poles of each battery are oriented
1 instruction manual (Spanish)
properly.
1 Quick Start Guide
•Never mix batteries of different types.
•Never mix old batteries and new ones.
1 ink roller (pre-installed)
1 take-up spool
Please read the instruction manual for
other battery handling precautions.
For further information, please read the instruction manual.
3
Installing Batteries
1. Push the paper roll release lever and
detach it.
2. Insert the paper straight into the
paper roll cradle.
View from rear
(Batteries are not supplied with the
3. (For journal printing) Insert the top
cash register.)
View from rear
"l l l l l " on the display will disappear.
Close the battery cover.
4. Attach the printer cover.
(For receipt printing, step 3 should be
omitted.)
4
Installing a Paper
Roll
Set the mode switch to the Z/PGM postition.
install the paper roll so that the paper
unrolls from the bottom.
Setting the Time
Enter the time in 4 digits ("hhmm" format) using the 24 hour
system. Press the
or twice to exit the programming mode.
Example:
f f f
f f
paper inlet, and press the key.
The inserted end comes out at the
printing area. Setting
Enter the date in 6 digits using the month-day-year
format. Press the
or twice to exit the programmig mode.
Example:
Setting Tax Rates (%)
Specify a tax rate (%) for calculation of tax on each
end of the paper into the slit in the
taxable subtotal using the following sequence:
take-up spool shaft and wind the
paper two or three turns. Then place
9
the take-up spool on the bearing.
➝
where
R: Tax rate (0.0000% to 99.9999%)x10000
(Enter the rate in 6 digits. Leading zeros may be
omitted.)
Q: Minimum taxable amount (0.01 to 99.99)x100
(Smallest amount for which tax must be collected. )
*Up to 4 types of tax are programmable.
Example:
NOTE
Your cash register is pre-programmed so that you can
use it with minimum set-up. To change the settings, see
the instruction manual.
Initial settings
Departments 1-4: Taxable 1
Departments 5-8: Non-taxable
Basic Programming
VOID
OFF X/F
REG
Z/PGM
#/ key once to program the next item
SBTL
#/ #/
SBTL SBTL
Time(2:30 p.m.)
the Date
#/
key once to program the next item
SBTL
#/ #/
SBTL SBTL
Date(March 15, 2002)
➝ ➝ ➝ ➝
Tax number (1-4)*
#/
@/TM
SBTL
➝ ➝
Q
@/TM
#/
@/TM
@/TM
SBTL
Tax 1 Tax rate(7.0000%) Min. taxable
amount($0.11)
Printed in Korea/Impreso en Corea
English
5
Now, you are ready!
Before Starting Entries Before Starting Entries
Set the mode switch to the REG Set the mode switch to the REG
postition. postition.
VOID
OFF X/F
REG
Z/PGM
Enter a clerk code (1-4) and press
CLK#
(Once the clerk code entered, re-entry
of the clerk code is not needed until
the clerk is changed.)
1 CLK#
Clerk code
Registration Example
(When the Customer Pays by Cash)
5
CLK#
1
Clerk code Price and dept.
7
#/
SBTL
3
R Price and dept.
Amount tendered
Reading and Resetting
X Reports (reading)
Set the mode switch to the X/F position
.
and press
Z Reports (reading and resetling)
.(
In the Z/PGM mode, press In this
case, grand total resetting is not performed.)
Flash Reports (displayed but not
printed)
In the X/F mode:
Press dept. key for dept. sales reports
Press for sales total reports
#/
SBTL
Press for cash-in-drawer reports
CH
O(TCADH2395BHZZ)1
.