Sign in today to find solutions:

Don't have an account? Sign up

 
CG-WLAPGMN
Wireless108M Access Point
User Manual

Summary of Contents

  • Page 1

    CG-WLAPGMN Wireless108M Access Point User Manual...

  • Page 3: Table Of Contents

    3. Setting WLAN adapter... 7 3.1 Setting up the Centrino in Win-XP(SP1) OS... 7 3.2 Setting up the Centrino in Win-XP(SP2) OS... 8 3.3 Setting up corega wireless adapter... 10 4. Setting Utility Program... 11 Step1. Setting TCP/IP... 11 Step2. Setting Web browser... 12 Step3.

  • Page 4: Regulatory Compliance

    Regulatory Compliance WLAPGMN User Manual FCC Interference Statement This device complies with Part 15 of FCC rule. Operation is subject to the following two conditions: • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired operation.

  • Page 5: Packing Content, Hardware Description

    WLAPGMN is a high speed Wireless Access Point, which support IEEE 802.11b/g standard with speed up to 108 Mbps provide higher data rate and through is suitable for user who has high speed transmission requirement. corega WLAPGMN supports enhanced security Functions to protect your PCs from outside intruders.

  • Page 6: Features

    WLAPGMN User Manual 1. LAN LED (Green) On: Connected Blink: Transmitting or receiving data OFF: Disconnected 2. WLAN LED (Green) ON: Connected Blink: Transmitting or receiving data OFF: Disconnected 3. Power LED(Green) Indicate power configuration 4. Detachable Antenna Connector 5. LAN port Be connected with PC or Hub 6.

  • Page 7: Hardware Installation, Environment Requirements, Install The Product

    Hardware Installation 2.1 Environment Requirements • A computer has configured TCP/IP • An availabe RJ-45 port on an Ethernet Hub/Switch/Router/Modem • A WLAN adapter which compliance with IEEE802.11g, IEEE802.11b, or IEEE802.11 standard. • Microsoft Internet Explorer 4.0 or Netscape Navigator 4.78 above browser.

  • Page 8: Connect To Wlan Adapter

    First at all, you have to prepare a WLAN adapter which has been installed in computer, and verify the setting of the WLAN adapter are the same as WLAPGMN, which default settings as below: • Communication Mode: Infrastru • ESSID: corega • Channel: 6 • WEP: OFF • WPA: OFF...

  • Page 9: Setting Wlan Adapter, Setting Up The Centrino In Win-xp(sp1) Os

    1. From the [Start Menu], select [Settings] -> [Control Panel]-> [Net- work]-> double click [Wireless network connection]. 2. It will show up the [Wireless Network Connection] screen, select [corega] in the listing of available wireless networks, => check [Allow me to connect...] box => click [Connect]. * Note: 1.“corega”...

  • Page 10: Setting Up The Centrino In Win-xp(sp2) Os

    3.2 Setting up the Centrino in Win-XP(SP2) OS 1. From the [Start Menu], select [Settings] -> [Control Panel]-> [Net- work]->double click [Wireless network connection]. 2. In following screen, please select [corega] in the listing of available wireless networks, => click [Connect].

  • Page 11

    3. If the WLAPGMN has not enable the security function, it will show up below screen, click [Connect Anyway] to continue. * Note: 1.“corega” is the default ESSID of WLAPGMN, once ESSID in WLAPGMN has been changed, the ESSID in WLAN adapter has to be changed, too.

  • Page 12

    If there’s no [Start] => [Programs]=>[corega CG-WLCB54GS]=> [Wireless LAN Utility]. 2. Please double click [corega] ESSID from [Available WLANs], then you’ll see it will be added in [Preferred WLANs] listing. 3. Now click [OK] then available to surf on internet by WLAPGMN.

  • Page 13: Setting Utility Program, Step1. Setting Tcp/ip

    Setting Utility Program This section take Windows XP for instance. Before starting, you have to set up TCP/IP and web browser first.The steps as below: Step1. Setting TCP/IP 1. From the [Start Menu], select [Settings] => select [Control Panel]=>select [Network]=> select [Connections], => click and press right button of the mouse, and select [properties].

  • Page 14: Step2. Setting Web Browser

    WLAPGMN User Manual 3. Select both [Use the following IP address] and [Use the follow- ing DNS server addresses] (Recommended). Enter the IP address between 192.168.1.1~192.168.254 range (except 192.168.1.230); submask is 255.255.255.0=>click [Advanced]. 4. Return back to [Local Area Connection Properties] screen => click [OK] to close it.

  • Page 15

    2. Click [Connections] tab=>select [LAN Settings]. 3. Please uncheck the three items in below screen (don’t select any- one)=> click [OK]. Uncheck these 3 items----> WLAPGMN User Manual...

  • Page 16: Step3. Setting Utility Program

    WLAPGMN User Manual 4. Please click [OK] to close the [Internet Options] screen. Step3. Setting Utility Program To make sure successful setting, please exit the virus and firewall pro- gram before setting the products. After setting completed, they can be opened again.

  • Page 17: Status, Wizard (quick Installation)

    You are now in the utility program for setting, details as below: 4.1 Status 1. Select [Stauts], it will display all status for corega WLAPGMN. 4.2 Wizard (Quick Installation) This section will lead you quick installation. 1. Select [Wizard] => Press [Next].

  • Page 18

    *Note: the default SSID(ESSID) is "corega", and default channel is 6. 3. Recommanded to click [Enable] from WEP setting screen, => select [64Bits], [128Bits], or [152Bits]=> key in password in Key1 tab, =>...

  • Page 19: Advanced, ConīŦguration

    4. Setting completed, please press [Reboot] for saving the changes. 5. It will show up Saving screen, few seconds later, it will return to re-login prompt box. 6. Change the same ESSID for all WLAN adapters which connected to WLAPGMN. 4.3 Advanced 4.3.1 Configuration <IP Address>...

  • Page 20

    WLAPGMN User Manual Item MAC Address Display corega WLAPGMN’s Mac address There are 2 selections: Manual and DHCP Get IP From * Default is [Manual]. IP Address Default is [192.168.1.230]. Subnet Mask Default is [255.255.255.0]. Default Gateway Default is [192.168.1.1].

  • Page 21

    Beacon Interval Default is [100], recommanded don't change it. (20-1000) DTIM (1-255) Default is [1], recommand don't change it. Fragmentation Enter even numbers. Length (256~2346) Default is [2346], recommanded don't change it. RTS Length Default is [2346], recommanded don't change it. (256~2346) Transmit Power Default is [full].

  • Page 22

    WLAPGMN User Manual Item Authentication Vaild Key First Key ~ Fourth Key * Note: If any setting has been changed, you have to click [Reboot]- >[Restart] to save the changes. B. Setting WPA WPA uses TKIP (Temporal Key Integrity Protocol) to change the temporal key every 10,000 packets (a packet is a kind of message transmitted over a network.) This ensures much greater security than the standard WEP security.There are two selections-[PSK] and [EAP] :...

  • Page 23

    2. Enter 9~63 characters in [PassPhrase]->select [Cipher Type], once configure completed, click [Apply]. * Note: 1. Group Key Update Interval: enter a number to indicate the key exchanged per minute. 2. If any setting has been changed, you have to click [Reboot]- >[Restart] to save the changes.

  • Page 24

    WLAPGMN User Manual 2. Enter 9~63 characters in [PassPhrase]->select [Cipher Type], setting [Security Server Settings] table, once configure completed, click [Apply]. * Note: If any setting has been changed, you have to click [Reboot]- >[Restart] to save the changes. <Access Control Settings> 1.

  • Page 25

    Item Disable: Disable the mac address filter function. Control Accept:Only connect with the mac address which list the table. Reject:Only conntect with the mac address which list the table. Enter the mac address of the WLAN adapter which connected MAC Address with computer.(character of 0~9;...

  • Page 26

    WLAPGMN User Manual 2. P to MP Bridge Mode: each one set the same channel, different ESSID Click[Advanced]->[Configuration]->[AP Mode]->[PtMP Bridge]- >enter Mac Address in [Remote AP MAC Address], once configure completed, click [Apply]. * Note: If any setting has been changed, you have to click [Reboot]- >[Restart] to save the changes.

  • Page 27

    3. Repeater Mode: each one set the same ESSID Click[Advanced]->[Configuration]->[AP Mode]->[AP Repeater]- >enter Mac Address in [Root AP MAC Address]->configure [Site Survey], once configure completed, click [Apply]. * Note: If any setting has been changed, you have to click [Reboot]- >[Restart] to save the changes.

  • Page 28

    WLAPGMN User Manual * Note: If any setting has been changed, you have to click [Reboot]- >[Restart] to save the changes. Internet Hub/Switch <WLAN Partition> Click[Advanced]->[Configuration]->[WLAN Partition]->check the box, once configure completed, click [Apply]. 26 26...

  • Page 29: Management

    * Note: If any setting has been changed, you have to click [Reboot]- >[Restart] to save the changes. <Device Information> Click[Advanced]->[Configuration]->[Device Information]->setting [System Name], once configure completed, click [Apply]. * Note: If any setting has been changed, you have to click [Reboot]- >[Restart] to save the changes.

  • Page 30: Maintenance

    WLAPGMN User Manual <Misc> Click[Advanced]->[Management]-[Misc], once configure completed, click [Apply]. * Note: If any setting has been changed, you have to click [Reboot]- >[Restart] to save the changes. 4.3.3 Maintenance <Update Firmware> Click[Advanced]->[Maintaince]->[Update Firmware]- >[Browse]=>select the path of the firmware file , =>click [OK]. * Note: If any setting has been changed, you have to click [Reboot]- >[Restart] to save the changes.

  • Page 31

    1. Click [Advanced]->[Maintenance]->[Restart System]->all new set- tings will be saved. 2. It will show up the Saving screen, several seconds later, it will return to re-login screen. * Note: • This function is the same as [Reboot]. • If any setting changes, please run this function to save and apply the changes.

  • Page 32: Statistics, Reboot

    WLAPGMN User Manual 4.4 Statistics The screen displays the statistics of throughput. 4.5 Reboot 1. Click [Reboot]->click [Restart], all new settings will be saved. 2. It will show up the Saving screen, severl seconds later, it will return to re-login screen. * Note: •...

  • Page 33

    There are 2 ways for solving your problems: (1) First, please see following “FAQ” to check your problem. (2) Please go to http://www.corega-asia.com, click “Supports”=>select “Online Customer Support” , => fill in the form, =>click “submit” . We’ll reply you as soon as possible.

  • Page 34

    WLAPGMN User Manual fire glass wall or door. It is to say to avoid the barriers between WLAPGMN and Wireless LAN adapter. 2. Shorten the distance between WLAPGMN and WLAN adapters. 3. Adjust the antenna direction. Q4. How to set/change the id and password for Utility Program? Ans: In utility program, Click[Advanced]->[Management]- >[Administration], Setting the id and password.

  • Page 35

    * Details please refer to [chapter 5. FAQ-Q6]. Q7. How to get the latest firmware? Ans: Please go to http://www.corega-asia.com, =>click supports >download >select “firmware” , =>select and click the model which you want to upgrade. If you upgraded failure, you may restore the utility system to factory default settings, please refer Q6.

  • Page 36

    Specification WLAPGMN User Manual Standard LAN Interface Frequency Band Transmission method Modulation system Memory Capacity Transmission speed Coverage Area Channel Security Antenna Type Power Specification Support OS Support Application Environment Requirements Operating Storage Physical Specification Dimension Case Material Weight Certification 34 34 34 WLAN:IEEE802.11 IEEE802.11b...

  • Page 37

    Established in 1986, corega 100% founded by Allied Tel- esis Group in Yokohama, Japan. corega’s core products consists of 10/100/1000 Ethernet products, Wireless Networking Products(802.11 a/b/g series), broadband...

  • Page 39

    Taiwan Inc. 7F., No. 10, Lane 345,YangGuang St. Nei-Hu Chiu, Taipei City 114, Taiwan R.O.C. TEL: +886-2-8751-9164 FAX: +886-2-8751-9174 PN: S30-UM8201-00 Rev.A...

Comments to this Manuals

Symbols: 0

Latest comments:

×

Select the desired size and copy embed code

Copy your embed code and put on your site: