Related Manuals for Seagate Momentus 5400.5 320GB
Summary of Contents for Seagate Momentus 5400.5 320GB
- Page 1 Product Manual Momentus 5400.5 SATA ST9320320AS ST9250320AS ST9200321AS ST9160310AS ST9160310ASG ST9120310AS ST9120310ASG ST980310AS ST980310ASG 100468844 Rev. B July 2008...
- Page 2 United States and/or other countries. Momentus, SeaTools and SeaTDD are either trademarks or registered trademarks of Seagate Technology LLC or one of its affiliated companies in the United States and/or other countries. All other trademarks or registered trademarks are the property of their respective owners.
- Page 3 Momentus 5400.5 SATA Product Manual, Rev. B...
- Page 4 Momentus 5400.5 SATA Product Manual, Rev. B...
-
Page 5: Table Of Contents
Seagate Technology support services ........ - Page 6 Momentus 5400.5 SATA Product Manual, Rev. B...
- Page 7 Figure 1. Typical +5V only startup and operation current profile ....... 9 Figure 2.
-
Page 9: Introduction
Introduction This manual describes the functional, mechanical and interface specifications for the following Seagate ® Momentus 5400.5 SATA model drives: • ST9320320AS • ST9250320AS • ST9200321AS • ST9160310AS • ST9160310ASG • ST9120310AS • ST9120310ASG • ST980310AS • ST980310ASG These drives provide the following key features: •... -
Page 10: About The Serial Ata Interface
About the Serial ATA interface The Serial ATA interface provides several advantages over the traditional (parallel) ATA interface. The primary advantages include: • Easy installation and configuration with true plug-and-play connectivity. It is not normally necessary to set any jumpers or other configuration options. •... -
Page 11: Drive Specifications
Drive specifications Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate the ST9320320AS, ST9250320AS, ST9120310ASG, ST980310AS and ST980310ASG models. Specification summary table The specifications listed in this table are for quick reference. - Page 12 Table 1: Drive specifications Drive specification ST9320320AS Track-to-track seek time, read (msec typical) Average seek, read (msec typical) Full-stroke seek, read (msec) 24 (typical) Startup current, +5V (max) 1.0 amps Seek power (typical) 1.54 watts Read/write power (typical) Read: 2.6 watts; Write: 2.85 watts Idle mode, low power (typical) 0.725 watts Standby mode...
-
Page 13: Formatted Capacity
To determine the warranty for a specific drive, use a web browser to access the following web page: www.seagate.com/support/service/ From this page, click on the “Verify Your Warranty” link. You will be asked to provide the drive serial number, model number (or part number) and country of purchase. The system will display the warranty information for your drive. -
Page 14: Physical Organization
Physical organization Drive model ST9320320AS ST9250320AS ST9200321AS ST9160310AS and ST9160310ASG ST9120310AS and ST9120310ASG ST980310AS and ST980310ASG Recording and interface technology Interface Recording method Recording density BPI (bits/inch avg) Track density TPI (tracks/inch avg) Areal density (Gbits/inch avg) Spindle speed (RPM) (± 0.2%) Maximum Internal transfer rate (Mbits/sec) I/O data-transfer rate (Mbytes/sec max) Interleave... -
Page 15: Seek Time
Seek time Seek measurements are taken with nominal power at 25°C ambient temperature. All times are measured using drive diagnostics. The specifications in the table below are defined as follows: • Track-to-track seek time is an average of all possible single-track seeks in both directions. •... -
Page 16: Power Specifications
Power specifications The drive receives DC power (+5V) through a native SATA power connector. 2.9.1 Power consumption Power requirements for the drives are listed in the table on page 8. Typical power measurements are based on an average of drives tested, under nominal conditions, at 25°C ambient temperature. •... -
Page 17: Deferred Spinup
2.9.1.1 Typical current profile Figure 1. Typical +5V only startup and operation current profile 2.9.2 Deferred spinup Momentus 5400.5 SATA drives do not support the deferred spinup option. If you require this option, refer to the Momentus 5400.3 SATA Blade Server family of drives. 2.9.3 Conducted noise Input noise ripple is measured at the host system power supply across an equivalent 15-ohm resistive load on... -
Page 18: Power-Management Modes
2.9.5 Power-management modes The drive provides programmable power management to provide greater energy efficiency. In most systems, you can control power management through the system setup program. The drive features the following power-management modes: Table 4: Power management modes Power modes Heads Active (operating) Tracking... -
Page 19: Temperature Gradient
Above 1,000 feet (305 meters), the maximum temperature is derated linearly by 1°C every 1000 feet. Operating: 0° to 60°C (32° to 140°F) Nonoperating: –40° to 70°C (–40° to 158°F) 2.10.2 Temperature gradient Operating 20°C per hour (68°F per hour max), without condensation Nonoperating 35°C per hour (95°F per hour max), without condensation 2.10.3... -
Page 20: Shock
2.10.5 Shock All shock specifications assume that the drive is mounted securely with the input shock applied at the drive mounting screws. Shock may be applied in the X, Y or Z axis. Note. Additional shock protection is provided by the Free Fall Protection feature on ST9160310ASG, ST9120310ASG and ST980310ASG models. -
Page 21: Acoustics
Seagate follows the ECMA-74 standards for measurement and identification of PDTs. An exception to this pro- cess is the use of the absolute threshold of hearing. Seagate uses the lower limit for the threshold curve* to discern tone audibility and to compensate for the inaudible components of sound prior to computation of tone ratios according to Annex D of the ECMA-74 standards. -
Page 22: Reliability
Information Technology Equipment (ITE). Emission levels are defined by EN 55022, Class B and the immunity levels are defined by EN 55024. Seagate uses an independent laboratory to confirm compliance with the EC directives specified in the previous paragraph. Drives are tested in representative end-user systems. Although CE-marked Seagate drives comply with the directives when used in the test systems, we cannot guarantee that all systems will comply with the directives. -
Page 23: Fcc Verification
As a subassembly, no Federal Communications Commission verification or certification of the device is required. Seagate Technology LLC has tested this device in enclosures as described above to ensure that the total assembly (enclosure, disc drive, motherboard, power supply, etc.) does comply with the limits for a Class B computing device, pursuant to Subpart J, Part 15 of the FCC rules. -
Page 24: Environmental Protection
The sil- ver, copper, nickel and gold films used in Seagate products are especially sensitive to the presence of sulfide, chloride, and nitrate contaminants. Sulfur is found to be the most damaging. In addition, electronic components should never be exposed to condensing water on the surface of the printed circuit board assembly (PCBA) or exposed to an ambient relative humidity greater than 95%. -
Page 25: Configuring And Mounting The Drive
Configuring and mounting the drive This section contains the specifications and instructions for configuring and mounting the drive. Handling and static-discharge precautions After unpacking, and before installation, the drive may be exposed to potential handling and electrostatic dis- charge (ESD) hazards. Observe the following standard handling and static-discharge precautions: Caution: •... -
Page 26: Configuring The Drive
Configuring the drive Each drive on the Serial ATA interface connects in a point-to-point configuration with the Serial ATA host adapter. There is no master/slave relationship because each drive is considered a master in a point-to-point relationships. If two drives are attached on one Serial ATA host adapter, the host operating system views the two devices as if they were both “masters”... -
Page 27: Drive Mounting
Drive mounting You can mount the drive using four screws in the side-mounting holes or four screws in the bottom-mounting holes. See Figure 4 for drive mounting dimensions. Follow these important mounting precautions when mount- ing the drive: • Allow a minimum clearance of 0.030 inches (0.76 mm) around the entire perimeter of the drive for cooling. •... - Page 28 Momentus 5400.5 SATA Product Manual, Rev. B...
-
Page 29: Serial Ata (Sata) Interface
Serial ATA (SATA) interface These drives use the industry-standard Serial ATA interface that supports FIS data transfers. It supports ATA programmed input/output (PIO) modes 0–4; multiword DMA modes 0–2, and Ultra DMA modes 0–6. The drive also supports the use of the IORDY signal to provide reliable high-speed data transfers. For detailed information about the Serial ATA interface, refer to the “Serial ATA: High Speed Serialized AT Attachment”... - Page 30 Table 7: Serial ATA connector pin definitions Segment Function Definition 3.3V power 3.3V power 3.3V power, pre-charge, 2nd mate Ground 1st mate Ground 2nd mate Ground 2nd mate 5V power, pre-charge, 2nd mate 5V power Power 5V power Ground 2nd mate Reserved The pin corresponding to P11 in the backplane receptacle connector is also reserved The corresponding pin to be mated with P11 in the power cable receptacle connector...
-
Page 31: Supported Ata Commands
Supported ATA commands The following table lists Serial ATA standard commands that the drive supports. For a detailed description of the ATA commands, refer to the Serial ATA: High Speed Serialized AT Attachment specification. See “S.M.A.R.T. commands” on page 31.for details and subcommands used in the S.M.A.R.T. implementation. Command name ATA-standard commands Device Configuration Restore... - Page 32 Command name Note: Individual Set Max commands are identi- fied by the value placed in the Set Max Fea- tures register as defined to the right. Set Multiple Mode S.M.A.R.T. Disable Operations S.M.A.R.T. Enable/Disable Autosave S.M.A.R.T. Enable Operations S.M.A.R.T. Enable/Disable Auto Offline S.M.A.R.T.
- Page 33 Command name ATA-standard security commands Security Set Password Security Unlock Security Erase Prepare Security Erase Unit Security Freeze Lock Security Disable Password Momentus 5400.5 SATA Product Manual, Rev. B Command code (in hex)
-
Page 34: Identify Device Command
4.3.1 Identify Device command The Identify Device command (command code EC power up. The data is organized as a single 512-byte block of data, whose contents are shown in the table on page 27. All reserved bits or words should be set to zero. Parameters listed with an “x” are drive-specific or vary with the state of the drive. - Page 35 Word Description Number of current logical heads Number of current logical sectors per logical track 57–58 Current capacity in sectors Number of sectors transferred during a Read Multiple or Write Multiple command 60–61 Total number of user-addressable sectors This field contains a value that is one greater than the total number of user-addressable sectors.
- Page 36 Free Fall Protection support (bit 5) Free Fall Protection enable/disable (bit 5) 121– ATA reserved Security status 129– Seagate-reserved 160– ATA-reserved Integrity word Note. See the bit descriptions below for words 63, 88, and 93 of the Identify Drive data:...
-
Page 37: Set Features Command
Ultra DMA mode 3 is supported. Ultra DMA mode 4 is supported. Ultra DMA mode 5 is supported Ultra DMA mode 6 is supported Ultra DMA mode 0 is currently active. Ultra DMA mode 1 is currently active. Ultra DMA mode 2 is currently active. Ultra DMA mode 3 is currently active. - Page 38 Table 8: Set Features command values Ultra DMA mode 5 Ultra DMA mode 6 Disable read look-ahead (read cache) feature. Disable write cache Enable read look-ahead (read cache) feature (default). Disable the Free Fall Protection feature (41 Report full capacity available Note.
-
Page 39: Commands
SeaTools diagnostic software activates a built-in drive self-test (DST S.M.A.R.T. command for D4 nates unnecessary drive returns. The diagnostic software ships with all new drives and is also available at: http://seatools.seagate.com. This drive is shipped with S.M.A.R.T. features disabled. You must have a recent BIOS or software package that supports S.M.A.R.T. - Page 40 Momentus 5400.5 SATA Product Manual, Rev. B...
-
Page 41: Seagate Technology Support Services
Seagate Service Centers Presales Support Our Presales Support staff can help you determine which Seagate products are best suited for your specific application or computer system, as well as product availability and compatibility. Technical Support Seagate technical support is available to assist you online at support.seagate.com... - Page 42 Seagate Customer Service Operations (CSO) representative for warranty- related issues. Resellers or end users of drive products should contact their place of purchase or Seagate warranty service for assistance. Have your serial number and model or part number available.
- Page 43 Index ACA 15 acoustics 4 Active mode 10 Address 23 AFR 14 Agency certification 14 Altitude 11 Altitude, nonoperating 4 Altitude, operating 4 Ambient temperature 4 ambient temperature 7 Annualized Failure Rate 14 Annualized Failure Rate (AFR) 4 Areal density 3 ATA commands 23 ATA data-transfer modes supported 3 Australia/New Zealand Standard AS/NZS3548 1995...
- Page 44 handling 17 Handling precautions 17 heads 5 Height 3 height 6 Humidity 11 humidity 4 I/O data-transfer rate 3 Identify 23 Identify Device 23 Identify Device command 26 Idle 8 Idle and Standby timers 10 Idle Immediate 24 Idle mode 4 Idle mode power 8 IEC950 14 Information Technology Equipment (ITE) 14...
- Page 45 read/write power and current 8 Recording density 3 Recording method 6 Recording technology 6 Relative humidity 4 Reliability 14 resistance 9 Retries 23 RF 13 RoHS 16 RPM 3 RRL 15 S.M.A.R.T. 24 S.M.A.R.T. implementation 23 Safety certification 14 SATA 6 screws 12 sector 5 sectors 5...
- Page 46 Momentus 5400.5 SATA Product Manual, Rev. B...
- Page 48 Seagate Technology LLC 920 Disc Drive, Scotts Valley, California 95066-4544, USA Publication Number: 100468844, Rev. B, Printed in USA...