Lorex W261AS-Z Quick Start Manual

Safety Precautions
• Read this guide carefully and keep it for future reference.
• Follow all instructions for safe use and handling of the product.
• Use the camera within given temperature, humidity and voltage levels
noted in the camera's specifications.
• Do not disassemble the camera.
• Do not point the camera directly at the sun or a source of intense light.
• Periodic cleaning may be required. Use a damp cloth only. Do not use any
harsh, chemical-based cleaners.
Dimensions Disclaimers
• The camera is rated for indoor use
only. Do not mount the camera
outdoors.
• Do not place the magnetic mounting
plate on or near other electrical
devices.
• This camera includes an Auto
Mechanical IR Cut Filter. When the
4.3" camera changes between Day/Night
viewing modes, an audible clicking
109mm
noise may be heard from the camera.
This clicking is normal, and indicates
that the camera filter is working.
• Audio recording without consent is
illegal in certain jurisdictions. Lorex
Corporation assumes no liability for
use of its products that does not
2.7" / 68mm
conform with local laws.
Need Help?
Visit us online for up-to-date software
and complete instruction manuals
1
Visit lorex.com
Search for the model
2
number of your product
Click on your product
3
in the search results
4
Click on the Downloads tab
Copyright © 2019 Lorex Corporation
As our products are subject to continuous improvement, Lorex reserves the right to
modify product design, specifications and prices, without notice and without incurring
any obligation. E&OE. All rights reserved.
W261AS_QSG_EN_R1.indd 1
Troubleshooting
Problem Solution
Cannot set up • Ensure your mobile device is within 1ft (30cm)
camera of the camera during setup.
No picture / signal • Ensure the LED indicator on the camera is
glowing steady green. See 'LED Behavior'
section for details if otherwise.
• Ensure the camera is properly connected to
power using the included USB power adapter.
• Try repositioning the camera, router, or both to
improve signal strength.
Picture is not clear • Check the camera lens for dirt, dust, and
spiderwebs. Clean the lens with a soft, clean
cloth.
• Remove the vinyl cover on the camera lens.
No audio • Ensure audio function on camera is turned on.
• Ensure audio is turned up on viewing device.
Person detection is • Ensure you have enabled Person Detection in
not working the Device Settings screen of the Lorex Home
app. See 'Overview of Lorex Home app' for
details.
LED Behavior
See table below for definitions of camera's LED behaviors:
Behavior Meaning
Operating correctly.
(steady)
Ready for connection.
(flashing)
Mobile device is attempting to connect to the camera.
(flashing rapidly)
Device malfunction. Try resetting the camera (see
(steady) 'Camera Overview' for details) and repeating the
setup.
Network connection failed. Try resetting the camera
(see 'Camera Overview' for details) and repeating the
(flashing)
setup.
microSD error. Try removing and re-inserting the
(flashing rapidly)
included microSD card, or try a different card.
(alternating)
Firmware upgrade in progress.
HD Wi-Fi Camera
W261AS Series
Quick Start Guide
lorex.com
Package Contents
Camera Power Accessories
ATTENTION:
A REGULATED UL / CSA APPROVED power supply is REQUIRED for use
with this camera (included). Use of a non-regulated, non-conforming power
supply can damage this product and voids the warranty.
Camera Overview
A Status LED
Microphone
B
A
C microSD slot: microSD card
pre-inserted (expandable up
to 256GB, microSD class 10
or higher).
D Speaker B
E Reset button: Press and hold
until the chime sounds to
reset the camera.
Power: Connect the included
F
USB power adapter.
×1 ×1
×1 ×3 ×3
Mounting Kit
C D
E
F
W261AS_QSG_EN_R1
2019-10-28 5:25:19 PM