Page 1 Install drivers Install programs SyncMaster 740B / 940B / 740N / 940Fn / 540B / 540N / 740T / 940T / 940N / 940Be...
Page 2 Notational Failure to follow directions noted by this symbol could result in bodily harm or damage to the equipment. Prohibited Do not disassemble Do not touch Power When not used for an extended period of time, set your computer to DPMS. If using a screen saver, set it to active screen mode.
Page 3 Do not use a damaged or loose plug. This may cause electric shock or fire. Do not pull the plug out by the wire nor touch the plug with wet hands. This may cause electric shock or fire. Use only a properly grounded plug and receptacle. An improper ground may cause electric shock or equipment damage.
Page 4 Installation Be sure to contact an authorized Service Center, when installing your monitor in a location with heavy dust, high or low temperatures, high humidity, and exposed to chemical substances and where it operates for 24 hours such as at airports, train stations etc.
Page 5 Put down the monitor carefully. Failing to do so may damage the monitor. Do not place the monitor face down. This may damage the TFT-LCD surface. The installation of the bracket must be done by a qualified professional. Installing the bracket by unqualified personnel may result in injury. Always use the mounting device specified in the owner's manual.
Page 6 Use the recommended detergent with a smooth cloth. If the connector between the plug and the pin is dusty or dirty, clean it properly using a dry cloth. A dirty connector may cause electric shock or fire. Make sure to unplug the power cord before cleaning the product. Otherwise, this may cause electric shock or fire.
Page 7 If the monitor is dropped or the casing is damaged, turn the monitor off and unplug the power cord. Then contact a Service Center. The monitor may malfunction, causing electric shock or fire. Disconnect the plug from the outlet during storms or lightning or if it is not used for a long period of time.
Page 8 Do not insert metal objects such as chopsticks, wire and tools or inflammable objects such as paper or matches into the vent, headphone port or AV ports. This may cause electric shock or fire. If an alien substances or water enters the product, turn the product off, unplug the power connector from the wall outlet and contact a Service Center.
Page 9 Otherwise, this may cause heat emission from the accumulated dirt or degraded insulation, causing electric shock or fire. Do not place your children's favorite toys or any other objects of interest on the product. Children may try to climb on the product to retrieve an object. The product could fall, causing physical damage or even death.
Page 10 Please make sure the following items are included with your monitor. If any items are missing, Contact a local dealer Unpacking Type 1 Monitor & Simple stand MagicRotation program can not be provided as Simple Stand does not support Pivot function. Type 2 Monitor &...
Page 11 Monitor & Sliding Stand Type 4 Monitor & Lowest HAS Stand Manual Quick Setup Guide Cable D-sub Cable Front User's Guide, Warranty Card Monitor Driver, (Not available in all Natural Color software, locations) MagicTune™ software MagicRotation software Power Cord DVI Cable (option)
Page 12 Opens the OSD menu. Also use to exit the OSD menu or return to MENU button [ ] the previous menu. MagicBright™™ is a new feature providing optimum viewing MagicBright™™ environment depending on the contents of the image you are watching.
Page 13 Use this button for auto adjustment. AUTO button Use this button for turn the monitor on and off. / Power button [ ]/ Power indicator This light glows blue during normal operation, and blinking blue once as the monitor saves your adjustments. PowerSaver described in the manual for further information regarding power saving functions.
Page 14 Please make sure the following items are included with your monitor. If any items are missing, Contact a local dealer Unpacking Type 1 Monitor & Simple stand MagicRotation program can not be provided as Simple Stand does not support Pivot function. Type 2 Monitor &...
Page 15 Quick Setup Guide Cable D-sub Cable Front MENU button [ ] Opens the OSD menu. Also use to exit the OSD menu or return to the previous menu. MagicBright™™ MagicBright™™ is a new feature providing optimum viewing environment depending on the contents of the image you are watching.
Page 16 2) Text 3) Internet 4) Game 5) Sport 6) Movie >>Click here to see an animation clip When OSD is not on the screen, push the button to adjust Brightness button brightness. ] Adjust items in the menu. Adjust buttons [ Activates a highlighted menu item.
Page 17 Simple stand (The configuration at the back of the monitor may vary from product to product.) Connect the power cord for your monitor to the power port on the back POWER port of the monitor. Connect the DVI Cable to the DVI port on the back of your monitor. DVI IN port Connect the signal cable to the 15-pin, D-sub port on the back of your RGB IN port...
Page 18 Please make sure the following items are included with your monitor. If any items are missing, Contact a local dealer Unpacking Type 1 Monitor & Simple stand MagicRotation program can not be provided as Simple Stand does not support Pivot function. Type 2 Monitor &...
Page 19 Monitor & Sliding Stand Type 4 Monitor & Lowest HAS Stand Manual Quick Setup Guide Cable D-sub Cable Front User's Guide, Warranty Card Monitor Driver, (Not available in all Natural Color software, locations) MagicTune™ software MagicRotation software Power Cord...
Page 20 Opens the OSD menu. Also use to exit the OSD menu or return to MENU button [ ] the previous menu. MagicBright™™ is a new feature providing optimum viewing MagicBright™™ environment depending on the contents of the image you are watching.
Page 21 PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. Rear Simple stand (The configuration at the back of the monitor may vary from product to product.) Connect the power cord for your monitor to the power port on the back POWER port of the monitor.
Page 22 Please make sure the following items are included with your monitor. If any items are missing, Contact a local dealer Unpacking Type 1 Monitor & Simple stand MagicRotation program can not be provided as Simple Stand does not support Pivot function. Type 2 Monitor &...
Page 23 Quick Setup Guide Cable D-sub Cable Front MENU button [ ] Opens the OSD menu. Also use to exit the OSD menu or return to the previous menu. MagicBright™™ MagicBright™™ is a new feature providing optimum viewing environment depending on the contents of the image you are watching.
Page 24 2) Text 3) Internet 4) Game 5) Sport 6) Movie >>Click here to see an animation clip When OSD is not on the screen, push the button to adjust Brightness button brightness. Adjust items in the menu. Adjust buttons [ Activates a highlighted menu item.
Page 25 of the monitor. RGB IN port Connect the signal cable to the 15-pin, D-sub port on the back of your monitor. Kensington Lock The Kensington lock is a device used to physically fix the system to something when using it in a public place. (The locking device has to be purchased separately.) For using a locking device, contact the place of purchase.
Page 26 SyncMaster 940Fn Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Contact a local dealer to buy optional items. Unpacking Monitor & Pivot stand Manual User's Guide, Warranty Card Monitor Driver, Quick Setup Guide (Not available in all Natural Color software,...
Page 27 Front Opens the OSD menu. Also use to exit the OSD menu or return to MENU button [ ] the previous menu. MagicBright™™ is a new feature providing optimum viewing MagicBright™™ environment depending on the contents of the image you are watching.
Page 28 Enter button [ ] / Activates a highlighted menu item. / Push the ' ', then selects the video signal while the OSD is off. Source button (When the source button is pressed to change the input mode, a message appears in the upper left of the screen displaying the current mode -- analog or digital input signal.) Note : If you select the digital mode, you must connect your monitor to the graphic card's DVI port using the DVI cable.
Page 29 Please make sure the following items are included with your monitor. If any items are missing, Contact a local dealer Unpacking Type 1 Monitor & Simple stand MagicRotation program can not be provided as Simple Stand does not support Pivot function. Type 2 Monitor &...
Page 30 Monitor & Lowest HAS Stand Manual User's Guide, Warranty Card Monitor Driver, Quick Setup Guide (Not available in all Natural Color software, locations) MagicTune™ software MagicRotation software Cable D-sub Cable Power Cord DVI Cable (option) Front...
Page 31 Opens the OSD menu. Also use to exit the OSD menu or return to MENU button [ ] the previous menu. MagicBright™™ is a new feature providing optimum viewing MagicBright™™ environment depending on the contents of the image you are watching.
Page 32 Use this button for auto adjustment. AUTO button Use this button for turn the monitor on and off. / Power button [ ]/ Power indicator This light glows blue during normal operation, and blinking blue once as the monitor saves your adjustments. PowerSaver described in the manual for further information regarding power saving functions.
Page 33 Please make sure the following items are included with your monitor. If any items are missing, Contact a local dealer Unpacking Type 1 Monitor & Simple stand MagicRotation program can not be provided as Simple Stand does not support Pivot function. Type 2 Monitor &...
Page 34 Quick Setup Guide Cable D-sub Cable Front MENU button [ ] Opens the OSD menu. Also use to exit the OSD menu or return to the previous menu. MagicBright™™ MagicBright™™ is a new feature providing optimum viewing environment depending on the contents of the image you are watching.
Page 35 2) Text 3) Internet 4) Game 5) Sport 6) Movie >>Click here to see an animation clip When OSD is not on the screen, push the button to adjust Brightness button brightness. ] Adjust items in the menu. Adjust buttons [ Activates a highlighted menu item.
Page 36 Simple stand (The configuration at the back of the monitor may vary from product to product.) Connect the power cord for your monitor to the power port on the back POWER port of the monitor. Connect the DVI Cable to the DVI port on the back of your monitor. DVI IN port Connect the signal cable to the 15-pin, D-sub port on the back of your RGB IN port...
Page 37: Connecting The Monitor
SyncMaster 740B / 940B / 540B / 740T / 940T / 940Be Connecting the Monitor Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. 2-1.
Page 38: Using The Stand
Using the Stand Monitor Assembly Monitor and Bottom Pivot Stand / Sliding Stand Attaching a Base This monitor accepts a 75 mm x 75 mm VESA-compliant mounting interface pad. A.Stand Stopper...
Page 39 Simple stand A. Monitor B. Mounting interface pad (Sold separately) 1. Turn off your monitor and unplug its power cord. 2. Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen. 3. Remove four screws and then remove the stand from the LCD monitor. 4.
Page 40 Connecting the Monitor Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. 2-1. Using the D-sub (Analog) connector on the video card. Connect the signal cable to the 15-pin, D-sub port on the back of your monitor.
Page 41 Monitor Assembly Monitor and Bottom Swivel stand Pivot Stand / Sliding Stand...
Page 42 Attaching a Base This monitor accepts a 75 mm x 75 mm VESA-compliant mounting interface pad. Simple stand A. Monitor B. Mounting interface pad (Sold separately) 1. Turn off your monitor and unplug its power cord. 2. Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen.
Page 43 Connecting the Monitor Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. 2-1. Using the D-sub (Analog) connector on the video card. Connect the 'DVI-A to D-SUB' Cable to the RGB IN port on the back of your monitor.
Page 44 Using the Stand Pivot Stand Attaching a Base This monitor accepts a 75 mm x 75 mm VESA-compliant mounting interface pad. A. Monitor B. Mounting interface pad (Sold separately) 1. Turn off your monitor and unplug its power cord. 2. Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen.
Page 45 Connecting the Monitor Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. 2-1. Using the D-sub (Analog) connector on the video card. Connect the signal cable to the 15-pin, D-sub port on the back of your monitor.
Page 46 Monitor Assembly Monitor and Bottom Pivot Stand A.Stand Stopper Attaching a Base This monitor accepts a 75 mm x 75 mm VESA-compliant mounting interface pad.
Page 47 Follow the directions appropriate for the operating system you have. Prepare a blank disk and download the driver program file at the Internet web site shown here. Internet web site : http://www.samsung.com/ http://www.samsung.com/monitor http://www.sec.co.kr/monitor http://www.samsungmonitor.com.cn/ 1. Insert CD into the CD-ROM drive.
Page 48 4. If you can see following message window, then click the "Continue Anyway" button. Then click "OK" button. (Microsoft This monitor driver is under certifying MS logo,and this installation don't damage your system.The certified driver will be posted on Samsung Monitor homepage http://www.samsung.com/.
Page 49 3. Click "Display" icon and choose the "Settings" tab then click "Advanced..". 4. Click the "Properties" button on the "Monitor" tab and select "Driver" tab. 5. Click "Update Driver.." and select "Install from a list or.." then click "Next" button. 6.
Page 50 8. If you can see following "Message" window, then click the "Continue Anyway" button. Then click "OK" button. This monitor driver is under certified MS logo,and this installation doesn't damage your system.The certified driver will be posted on Samsung Monitor homepage. http://www.samsung.com/ 9. Click the "Close" button then click "OK" button continually.
Page 51 10. Monitor driver installation is completed. ® ® Microsoft Windows 2000 Operating System When you can see "Digital Signature Not Found" on your monitor, follow these steps. 1. Choose "OK" button on the "Insert disk" window. 2. Click the "Browse" button on the "File Needed" window. 3.
Page 52 Samsung Electronics in association with Korea Electronics & Telecommunications Research Institute (ETRI). This is only available for Samsung monitors and ensures that the color of the images on the monitor are the same as the printed or scanned images.
Page 53 ROM Drive, click the Windows [Start] button, select [Run...]. Enter D:\color\NCProsetup.exe and then press the <Enter> key. (If the drive where the CD is inserted is not D:\, enter the applicable drive.) Uninstalling the Natural Color Software Program Select "Setting/Control Panel" on the "Start" menu and then double-click "Add/Delete a program".
Page 54 SyncMaster 740B / 940B 1. [ ]Opens the on-screen menu and exits from the menu or closes the adjustment menu. 2. [ ]This button allows you to adjust items in the menu. 3. [ ]Press this button to Activates a highlighted menu item. 4.
Page 55 Menu Description When the 'AUTO' button is pressed, the Auto Adjustment screen appears as shown in the animated screen on the center. Auto adjustment allows the monitor to self-adjust to the incoming video signal. The values of fine, coarse and position are adjusted automatically. (Available in analog mode only) To make the automatic adjustment function sharper, execute the 'AUTO' AUTO...
Page 56 Menu After pushing the "MENU" button more than 5 seconds, OSD function is locked (unlocked). Locked You can also adjust the brightness and contrast of the monitor with the OSD adjustment locking feature. MagicBright™ Menu Push the MagicBright button to circle through available preconfigured MagicBright™...
Page 57 Brightness Menu Brightness When OSD is not on the screen, push the button to adjust brightness. SOURCE Menu Selects the video signal while the OSD is off. SOURCE Description Description...
Page 58 Brightness Contrast Picture Color MagicColor Color Tone Image Coarse Fine Language H-Position Setup Auto Source Image Reset Information Picture Menu You can use the on-screen menus to change the brightness according to personal preference. Brightness Direct Access Feature : When OSD is not on the screen, push the button to adjust brightness.
Page 59 Menu MagicColor is a new technology that Samsung has exclusively developed to improve digital image and to display natural color more clearly without disturbing image quality. 1) Off - Returns to the original mode. 2) Demo - The screen before applying MagicColor appears on the right and the screen after applying MagicColor appears on the left.
Page 60 : This function is to adjust the vertical size of the MagicZone. The tone of the color can be changed and one of four modes can be selected - Cool, Normal, Warm and Color Tone Custom. (Not available in MagicColor mode of Full and Adjusts individual R,G,B color balance.
Page 61 display. V-Position (Available in analog mode only) Menu You can choose one of 9 languages. Language Note:The language chosen affects only the language of the OSD. It has no effect on any software running on the computer. You can change the horizontal position where the OSD H-Position menu appears on your monitor.
Page 62 Menu Description Play/Stop Select Auto Source for the monitor to automatically select Auto Source the signal source. Image parameters are replaced with the factory default Image Reset values. Color parameters are replaced with the factory default Color Reset values. Information...
Page 63 Menu Description Information Shows a video source, display mode on the OSD screen.
Page 64 SyncMaster 740N / 940N 1. [ ]Opens the on-screen menu and exits from the menu or closes the adjustment menu. 2. [ ]This button allows you to adjust items in the menu. 3. [ ]Press this button to Activates a highlighted menu item. 4.
Page 65 Menu Description When the 'AUTO' button is pressed, the Auto Adjustment screen appears as shown in the animated screen on the center. Auto adjustment allows the monitor to self-adjust to the incoming video signal. The values of fine, coarse and position are adjusted automatically. (Available in analog mode only) To make the automatic adjustment function sharper, execute the 'AUTO' AUTO...
Page 66 Menu After pushing the "MENU" button more than 5 seconds, OSD function is locked (unlocked). Locked You can also adjust the brightness and contrast of the monitor with the OSD adjustment locking feature. MagicBright™ Menu Push the MagicBright button to circle through available preconfigured MagicBright™...
Page 67 Brightness Menu Brightness When OSD is not on the screen, push the button to adjust brightness. Brightness Contrast Picture MagicColor Color Tone Color Coarse Fine Image Language H-Position Setup Image Reset Color Reset Information Picture Description Color Control Gamma Sharpness H-Position V-Position Transparency...
Page 68 Menu Description Play/Stop You can use the on-screen menus to change the brightness according to personal preference. Brightness Direct Access Feature : When OSD is not on the screen, push the button to adjust brightness. You can use the on-screen menus to change the contrast Contrast according to personal preference.
Page 69 Menu MagicColor is a new technology that Samsung has exclusively developed to improve digital image and to display natural color more clearly without disturbing image quality. 1) Off - Returns to the original mode. 2) Demo - The screen before applying MagicColor appears on the right and the screen after applying MagicColor appears on the left.
Page 70 Menu Description Play/Stop Removes noise such as vertical stripes. Coarse adjustment may move the screen image area. You may Coarse relocate it to the center using the horizontal control menu. (Available in analog mode only) Removes noise such as horizontal stripes. If the noise persists even after fine tuning, repeat it after adjusting the Fine frequency (clock speed).
Page 71 Menu Description Play/Stop You can choose one of 9 languages. Language Note:The language chosen affects only the language of the OSD. It has no effect on any software running on the computer. You can change the horizontal position where the OSD H-Position menu appears on your monitor.
Page 72 Menu Image parameters are replaced with the factory default Image Reset values. Color parameters are replaced with the factory default Color Reset values. Information Menu Shows a video source, display mode on the OSD screen. Information Description Description Play/Stop...
Page 73 SyncMaster 940Fn 1. [ ]Opens the on-screen menu and exits from the menu or closes the adjustment menu. 2. [ ]This button allows you to adjust items in the menu. 3. [ ]Press this button to Activates a highlighted menu item. 4.
Page 74 Menu Description When the 'AUTO' button is pressed, the Auto Adjustment screen appears as shown in the animated screen on the center. Auto adjustment allows the monitor to self-adjust to the incoming video signal. The values of fine, coarse and position are adjusted automatically. (Available in analog mode only) To make the automatic adjustment function sharper, execute the 'AUTO' AUTO...
Page 75 Menu After pushing the "MENU" button more than 5 seconds, OSD function is locked (unlocked). Locked You can also adjust the brightness and contrast of the monitor with the OSD adjustment locking feature. MagicBright™ Menu Push the MagicBright button to circle through available preconfigured MagicBright™...
Page 76 Brightness Menu Brightness When OSD is not on the screen, push the button to adjust brightness. SOURCE Menu Selects the video signal while the OSD is off. SOURCE Description Description...
Page 77 Brightness Contrast Picture Color MagicColor Color Tone Image Coarse Fine Language H-Position Setup Auto Source Image Reset Information Picture Menu You can use the on-screen menus to change the brightness according to personal preference. Brightness Direct Access Feature : When OSD is not on the screen, push the button to adjust brightness.
Page 78 Menu MagicColor is a new technology that Samsung has exclusively developed to improve digital image and to display natural color more clearly without disturbing image quality. 1) Off - Returns to the original mode. 2) Demo - The screen before applying MagicColor appears on the right and the screen after applying MagicColor appears on the left.
Page 79 : This function is to adjust the vertical size of the MagicZone. The tone of the color can be changed and one of four modes can be selected - Cool, Normal, Warm and Color Tone Custom. (Not available in MagicColor mode of Full and Adjusts individual R,G,B color balance.
Page 80 display. V-Position (Available in analog mode only) Menu You can choose one of eight languages. Language Note:The language chosen affects only the language of the OSD. It has no effect on any software running on the computer. You can change the horizontal position where the OSD H-Position menu appears on your monitor.
Page 81 Menu Description Play/Stop Select Auto Source for the monitor to automatically select Auto Source the signal source. Image parameters are replaced with the factory default Image Reset values. Color parameters are replaced with the factory default Color Reset values. This is a source-switch function according to the priority Priority that the user has set for the source.
Page 82 Menu Description Shows a video source, display mode on the OSD screen. Information...
Page 83 SyncMaster 540B / 740T / 940T / 940Be 1. [ ]Opens the on-screen menu and exits from the menu or closes the adjustment menu. 2. [ ]This button allows you to adjust items in the menu. 3. [ ]Press this button to Activates a highlighted menu item. 4.
Page 84 Menu Description When the 'AUTO' button is pressed, the Auto Adjustment screen appears as shown in the animated screen on the center. Auto adjustment allows the monitor to self-adjust to the incoming video signal. The values of fine, coarse and position are adjusted automatically. (Available in analog mode only) To make the automatic adjustment function sharper, execute the 'AUTO' AUTO...
Page 85 Menu After pushing the "MENU" button more than 5 seconds, OSD function is locked (unlocked). Locked You can also adjust the brightness and contrast of the monitor with the OSD adjustment locking feature. MagicBright™ Menu Push the MagicBright button to circle through available preconfigured MagicBright™...
Page 86 Brightness Menu Brightness When OSD is not on the screen, push the button to adjust brightness. SOURCE Menu Selects the video signal while the OSD is off. SOURCE Description Description...
Page 87 Brightness Contrast Picture Color MagicColor Color Tone Image Coarse Fine Language H-Position Setup Auto Source Image Reset Information Picture Menu You can use the on-screen menus to change the brightness according to personal preference. Brightness Direct Access Feature : When OSD is not on the screen, push the button to adjust brightness.
Page 88 Menu MagicColor is a new technology that Samsung has exclusively developed to improve digital image and to display natural color more clearly without disturbing image quality. 1) Off - Returns to the original mode. 2) Demo - The screen before applying MagicColor appears on the right and the screen after applying MagicColor appears on the left.
Page 89 : This function is to adjust the vertical size of the MagicZone. The tone of the color can be changed and one of four modes can be selected - Cool, Normal, Warm and Color Tone Custom. (Not available in MagicColor mode of Full and Adjusts individual R,G,B color balance.
Page 90 display. V-Position (Available in analog mode only) Menu You can choose one of eight languages. Language Note:The language chosen affects only the language of the OSD. It has no effect on any software running on the computer. You can change the horizontal position where the OSD H-Position menu appears on your monitor.
Page 91 Menu Description Play/Stop Select Auto Source for the monitor to automatically select Auto Source the signal source. Image parameters are replaced with the factory default Image Reset values. Color parameters are replaced with the factory default Color Reset values. Information...
Page 92 Menu Description Information Shows a video source, display mode on the OSD screen.
Page 93 SyncMaster 540N 1. [ ]Opens the on-screen menu and exits from the menu or closes the adjustment menu. 2. [ ]This button allows you to adjust items in the menu. 3. [ ]Press this button to Activates a highlighted menu item. 4.
Page 94 Menu Description When the 'AUTO' button is pressed, the Auto Adjustment screen appears as shown in the animated screen on the center. Auto adjustment allows the monitor to self-adjust to the incoming video signal. The values of fine, coarse and position are adjusted automatically. (Available in analog mode only) To make the automatic adjustment function sharper, execute the 'AUTO' AUTO...
Page 95 Menu After pushing the "MENU" button more than 5 seconds, OSD function is locked (unlocked). Locked You can also adjust the brightness and contrast of the monitor with the OSD adjustment locking feature. MagicBright™ Menu Push the MagicBright button to circle through available preconfigured MagicBright™...
Page 96 Brightness Menu Brightness When OSD is not on the screen, push the button to adjust brightness. Brightness Contrast Picture MagicColor Color Tone Color Coarse Fine Image Language H-Position Setup Image Reset Color Reset Information Picture Description Color Control Gamma Sharpness H-Position V-Position Transparency...
Page 97 Menu Description Play/Stop You can use the on-screen menus to change the brightness according to personal preference. Brightness Direct Access Feature : When OSD is not on the screen, push the button to adjust brightness. You can use the on-screen menus to change the contrast Contrast according to personal preference.
Page 98 Menu MagicColor is a new technology that Samsung has exclusively developed to improve digital image and to display natural color more clearly without disturbing image quality. 1) Off - Returns to the original mode. 2) Demo - The screen before applying MagicColor appears on the right and the screen after applying MagicColor appears on the left.
Page 99 Menu Description Play/Stop Removes noise such as vertical stripes. Coarse adjustment may move the screen image area. You may Coarse relocate it to the center using the horizontal control menu. (Available in analog mode only) Removes noise such as horizontal stripes. If the noise persists even after fine tuning, repeat it after adjusting the Fine frequency (clock speed).
Page 100 Menu Description Play/Stop You can choose one of 8 languages. Language Note:The language chosen affects only the language of the OSD. It has no effect on any software running on the computer. You can change the horizontal position where the OSD H-Position menu appears on your monitor.
Page 101 Menu Image parameters are replaced with the factory default Image Reset values. Color parameters are replaced with the factory default Color Reset values. Information Menu Shows a video source, display mode on the OSD screen. Information Description Description Play/Stop...
Page 102 Overview Installation Overview What is MagicTune™ ? Monitor performance can vary due to the graphics card, host computer lighting conditions and other environmental factors. In order to get the best image on a monitor requires you to adjust it for your unique setting.
Page 103 The OSD mode allows easy adjustment of monitor settings without taking pre-defined steps. You can access the desired menu item to set with ease.
Page 104: System Requirements
Overview Installation Installation 1. Insert the installation CD into the CD-ROM drive. 2. Click the MagicTune™ installation file. 3. Select installation Language, Click "Next". 4. When the Installation Shield Wizard window appears, click "Next." 5. Select "I agree to the terms of the license agreement" to accept the terms of use. 6.
Page 105 Windows™ 2000 Windows™ XP Home Edition Windows™ XP Professional Hardware 32 MB Memory above 60 MB Hard disk space above * For more information, visit the MagicTune™ It is recommended using MagicTune™ in Windows™ 2000 or later. website...
Page 106 Overview Installation MagicTune™ allows for quick accurate tuning of the display with the ability to easily save and use monitor configurations that are best suited for you. OSD mode may appear inconsistent with the explanation in guidance book depending on specification of each monitor. When Pivot is functioning, part of MagicTune™...
Page 107 Picture Tab Definition Allows the user to adjust the screen settings to the desired values. Makes the entire screen brighter or darker. The detailed data of the images in the dark Brightness areas can be lost if the brightness is not adjusted to the proper level. Adjust the brightness for best viewing conditions.
Page 108 - including web images and ones produced by a digital camera or scanner. MagicColor is a new technology that Samsung has exclusively developed to improve digital image and to display natural color more clearly without disturbing image quality.
Page 109 MagicColor Color Innovation function provides optimized color for personal favor to view effectively with WCG-CCFL which was applied to Samsung Electronics for the first time. Color Innovation Brilliant : If you select "Brilliant", you can view a more clear and vibrant image.
Page 110 Hue - To adjust the color tone. Reset - To reset the monitor settings to the factory defaults. Image Tab Definition Adjusts the Fine , Coarse and Position values. Fine : Removes noise such as horizontal stripes. If the noise persists even after Fine tuning, repeat it after adjusting the frequency (clock speed).
Page 111 Custom - Partial Color Blindness Test Reset - To reset the monitor settings to the factory defaults. When external A/V devices such as VCRs or DVDs are connected to the monitor, PIP allows you to watch video from those devices in a small window super-imposed on the PC Video signal.
Page 112 you can use the server to control the Client monitor. (Server program should be installed to use this program as Client) When selecting the Customize checkbox at the bottom you can enter your personal information. Asset ID User Name User ID Server IP Department Location...
Page 113: Color Calibration
Overview Installation Color Calibration 1. Color Calibration Color Calibration guides you to get optimal color condition for your monitor. Proceed following 5steps for getting optimal monitor color condition . 1. Control "Brightness control bar" for matching the brightness of control patch and the brightness of background pattern 2.
Page 114 The above picture will be shown. 1. Press "View Calibrated" button to see the calibration effect which you adjusted. 2. Press "View Uncalibrated" button to see the original image.
Page 115 Overview Installation Uninstall The MagicTune™ program can be removed only by using the "Add or Remove Programs" option of the Windows™ Control Panel. Perform the following steps remove MagicTune™ . 1. Go to [Task Tray] ' [Start] ' [Settings] and select [Control Panel] in the menu. If the program runs on Windows™...
Page 116: Troubleshooting
Products from other manufacturers may cause errors. Only Samsung products are able to support this feature. An error may occur even when your monitor is manufactured by Samsung but is out of date. Check if your monitor is able to support MagicTune™ .
Page 117 Hardware > Device Manager > Monitor is selected, the current "Plug-and-play monitor" is removed and new hardware is searched for but the system couldn't find any "Plug-and-play monitor". Please visit our homepage to see the Troubleshooting section. An error occurs when replacing the monitor with a new one when the system power is off but the system has not been restarted.
Page 118 As the Highlight program uses the communication lines, please exit the Highlight program before you can access MagicTune™ . Some of Samsung CDT monitors support the Highlight feature. When using both the Highlight feature and MagicTune™ simultaneously, conflicts occur, which cause errors.
Page 119 website Visit the MagicTune™ for technical support for MagicTune™ , FAQs (questions and answers) and software upgrades. website Visit the MagicTune™ and download the installation software for MagicTune™ MAC. program is already installed, remove it, reboot the computer, and then install the program again.
Page 120 This greatly improves the user's productivity allowing him the flexibility to switch between landscape and portrait modes. The MagicRotation Software from Samsung Electronics, Inc. provides the user with a rotation feature (0, 90, 180, 270 orientation) that facilitates the optimum utilization of computer display screen, better viewing and improved user productivity.
Page 121 Overview Installation Interface Uninstall Troubleshooting Installation 1. Insert the installation CD into the CD-ROM drive. 2. Click the MagicRotation installation file. 3. Select installation Language, Click "Next". 4. When the InstallShield Wizard window appears, click "Next." 5. Select "I accept the terms of the license agreement" to accept the terms of use.
Page 122 6. Choose a folder to install the MagicRotation program. 7. Click "Install." 8. The "Setup Status" window appears.
Page 123: Installation Problems
9. Click "Finish." Have to reboot the system in order for the MagicRotation to work properly. 10. When the installation is complete, the MagicRotation executable icon appears on your desktop. Installation Problems The installation of MagicRotation can be affected by the factors such as video card, motherboard and the network environment.
Page 124 movie files properly in 90, 180 and 270 orientations then do the following : Close the application. Select the Orientation (90, 180, 270) you want to view the application. Relaunch the application. In most cases this should fix the problem. 3.
Page 125 Overview Installation Interface When Rotation is functioning, portion of MagicTune™ program may not operate normally. AutoRotation : The screens display will automatically rotate when the monitor is rotated. To execute Auto Rotation, it should be done as below. Please install both MagicRotation and MagicTune™ 3.6 programs in your computer.
Page 126 Rotate to 90 : Display will be rotated 90 degrees from the current angle. Rotate to 180 : Display will be rotated 180 degrees from the current angle.
Page 127 Rotate to 270 : Display will be rotated 270 degrees from the current angle. Hot key : Hot Keys are available by default and can be changed by user. It can be assigned by user directly with keyboard after changing the existing HotKey .
Page 129 Overview Installation Interface Uninstall The MagicRotation program can be removed only by using the "Add/Remove Programs" option of the Windows Control Panel. Perform the following steps to remove MagicRotation. 1. Go to [Task Tray] ' [Start] ' [Settings] and select [Control Panel] in the menu. If the program runs on Windows™...
Page 130 Overview Installation Interface Troubleshooting Before You Call Technical Support MagicRotation Software works with the installed "Display Driver" supplied by your Graphic Card Vendor to provide screen rotation capabilities. If the installed "Display Driver" is working incorrectly or has bugs in it, then these bugs would still exist even after MagicRotation Software is installed.
Page 131: Check List
SyncMaster 740B / 940B / 540B / 740T / 940T / 940Be Check List Before calling for assistance, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call Information section or contact your Symptom Check List...
Page 132 There is no image on the screen. Is the power indicator on the monitor blinking at 1 second intervals? Connected using the DVI cable? I cannot see the On Have you locked the On Screen Display. Screen Display (OSD) Menu to prevent changes? The screen shows Is the screen displaying strange colors or just...
Page 133 When you have a problem with the graphic card, visit our website to check the compatible graphic card list provided. http://www.samsung.com/monitor/magictune Download the latest program. The program can be downloaded http://www.samsung.com/monitor/magictune. contact an authorized service center.
Page 134 Q & A Question How can I change the frequency? How can I adjust the resolution? How can I set the Power Saving function? How can I clean the outer case/LCD Panel? Self-Test Feature Check Self-Test Feature Check Warning Messages Your monitor provides a self test feature that allows you to check whether your monitor is functioning properly.
Page 135 Environment The location and the position of the monitor may influence the quality and other features of the monitor. 1. if there are any sub woofer speakers near the monitor, unplug and relocate the woofer to another room. 2. Remove all electronic devices such as radios, fans, clocks and telephones that are within 3 feet (one meter) of the monitor.
Page 136 Check List Before calling for assistance, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call Information section or contact your Symptom Check List No images on the Is the power cord screen.
Page 137 There is no image on the screen. Is the power indicator on the monitor blinking at 1 second intervals? The screen shows Is the screen displaying strange colors or just only one color as if looking black and white. at the screen through a cellophane paper? Have the screen colors become strange after...
Page 138 When you have a problem with the graphic card, visit our website to check the compatible graphic card list provided. http://www.samsung.com/monitor/magictune Download the latest program. The program can be downloaded http://www.samsung.com/monitor/magictune. contact an authorized service Answer The frequency can be changed by reconfiguring the video card.
Page 139 Self-Test Feature Check Self-Test Feature Check Warning Messages Your monitor provides a self test feature that allows you to check whether your monitor is functioning properly. Self-Test Feature Check 1. Turn off both your computer and the monitor. 2. Unplug the video cable from the back of the computer. 3.
Page 140 1024 60 Hz" message comes up, disconnect the cable from the computer while the monitor is still powered on. If there is a message coming up on the screen or if the screen goes white, this means the monitor is in working condition. In this case, check the computer for trouble.
Page 141 Check List Before calling for assistance, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call Information section or contact your Symptom Check List No images on the Is the power cord screen.
Page 142 There is no image on the screen. Is the power indicator on the monitor blinking at 1 second intervals? Connected using the DVI cable? I cannot see the On Have you locked the On Screen Display. Screen Display (OSD) Menu to prevent changes? The screen shows Is the screen displaying strange colors or just...
Page 143 When you have a problem with the graphic card, visit our website to check the compatible graphic card list provided. http://www.samsung.com/monitor/magictune Download the latest program. The program can be downloaded http://www.samsung.com/monitor/magictune. contact an authorized service center.
Page 144 Q & A Question How can I change the frequency? How can I adjust the resolution? How can I set the Power Saving function? How can I clean the outer case/LCD Panel? Self-Test Feature Check Self-Test Feature Check Warning Messages Your monitor provides a self test feature that allows you to check whether your monitor is functioning properly.
Page 145 Environment The location and the position of the monitor may influence the quality and other features of the monitor. 1. if there are any sub woofer speakers near the monitor, unplug and relocate the woofer to another room. 2. Remove all electronic devices such as radios, fans, clocks and telephones that are within 3 feet (one meter) of the monitor.
Page 146 General General Model Name SyncMaster 740B LCD Panel Size 17 " Diagonal (43 cm) Display area 337.92 mm (H) x 270.336 mm (V) Pixel Pitch 0.264 mm (H) x 0.264 mm (V) Synchronization Horizontal 30 ~ 81 k Hz Vertical 56 ~ 75 Hz Display Color 16.2 M Colors...
Page 147 Dimensions (WxHxD)/ Weight (Pivot Stand) 366.0 x 391.2 x 200.0 mm / 14.4 x 15.4 x 7.9 inch (with Basic Stand) / 4.7 kg Dimensions (WxHxD)/ Weight (Sliding Stand) 366.0 x 391.2 x 200.0 mm / 14.4 x 15.4 x 7.9 inch (with Basic Stand) / 4.7 kg Dimensions (WxHxD)/ Weight (Lowest HAS Stand) 366.0 x 351.4 x 200.0 mm / 14.4 x 13.8 x 7.9 inch (with Basic Stand) / 4.8 kg VESA Mounting Interface...
Page 148 Horizontal Cycle is called the Horizontal Frequency. Unit: kHz Vertical Frequency Like a fluorescent lamp, the screen has to repeat the same image ® compliant and ENERGY2000 ® Partner, SAMSUNG has determined that this ® guidelines for energy efficiency. Vertical Pixel Clock Frequency (MHz) (Hz) 70.086...
Page 149 many times per second to display an image to the user. The frequency of this repetition is called the Vertical Frequency or Refresh Rate. Unit: Hz...
Page 150 General General Model Name SyncMaster 940B LCD Panel Size 19 " Diagonal (48 cm) Display area 376.32 mm (H) x 301.056 mm (V) Pixel Pitch 0.294 mm (H) x 0.294 mm (V) Synchronization Horizontal 30 ~ 81 k Hz Vertical 56 ~ 75 Hz Display Color 16.7 M Colors...
Page 151 Dimensions (WxHxD)/ Weight (Pivot Stand) 407.6 x 408.0 x 200.0mm / 16.0 x 16.1 x 7.9 inch (with Basic Stand) / 5.55 kg Dimensions (WxHxD)/ Weight (Sliding Stand) 407.6 x 408.0 x 200.0mm / 16.0 x 16.1 x 7.9 inch (with Basic Stand) / 5.7 kg Dimensions (WxHxD)/ Weight (Lowest HAS Stand) 407.6 x 368.2 x 200.0 mm / 16.0 x 14.5 x 7.9 inch (with Basic Stand) / 5.8 kg VESA Mounting Interface...
Page 152 Horizontal Cycle is called the Horizontal Frequency. Unit: kHz Vertical Frequency Like a fluorescent lamp, the screen has to repeat the same image ® compliant and ENERGY2000 ® Partner, SAMSUNG has determined that this ® guidelines for energy efficiency. Vertical Pixel Clock Frequency (MHz) (Hz) 70.086...
Page 153 many times per second to display an image to the user. The frequency of this repetition is called the Vertical Frequency or Refresh Rate. Unit: Hz...
Page 154 General General Model Name SyncMaster 740N LCD Panel Size 17 " Diagonal (43 cm) Display area 337.92 mm (H) x 270.336 mm (V) Pixel Pitch 0.264 mm (H) x 0.264 mm (V) Synchronization Horizontal 30 ~ 81 k Hz Vertical 56 ~ 75 Hz Display Color 16.2 M Colors...
Page 155 366.0 x 391.2 x 200.0 mm / 14.4 x 15.4 x 7.9 inch (with Basic Stand) / 4.7 kg Dimensions (WxHxD)/ Weight (Sliding Stand) 366.0 x 391.2 x 200.0 mm / 14.4 x 15.4 x 7.9 inch (with Basic Stand) / 4.7 kg Dimensions (WxHxD)/ Weight (Lowest HAS Stand) 366.0 x 351.4 x 200.0 mm / 14.4 x 13.8 x 7.9 inch (with Basic Stand) / 4.8 kg VESA Mounting Interface...
Page 156 Horizontal Cycle is called the Horizontal Frequency. Unit: kHz Vertical Frequency Like a fluorescent lamp, the screen has to repeat the same image ® Partner, SAMSUNG has determined that this ® guidelines for energy efficiency. Vertical Pixel Clock...
Page 157 many times per second to display an image to the user. The frequency of this repetition is called the Vertical Frequency or Refresh Rate. Unit: Hz...
Page 158 General General Model Name SyncMaster 940Fn LCD Panel Size 19 " Diagonal (48 cm) Display area 376.32 mm (H) x 301.056 mm (V) Pixel Pitch 0.294 mm (H) x 0.294 mm (V) Synchronization Horizontal 30 ~ 81 k Hz Vertical 56 ~ 75 Hz Display Color 16.7 M Colors...
Page 159 VESA Mounting Interface 75 mm x 75 mm (for use with Specialty(Arm) Mounting hardware.) Environmental considerations Operating Storage Plug and Play Capability This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor installation will proceed automatically, unless the user wishes to select alternate settings.
Page 160 Table 1. Preset Timing Modes Horizontal Display Mode Frequency (kHz) IBM, 640 x 350 31.469 IBM, 640 x 480 31.469 IBM, 720 x 400 31.469 MAC, 640 x 480 35.000 MAC, 832 x 624 49.726 MAC, 1152 x 870 68.681 VESA, 640 x 480 37.500 VESA, 640 x 480...
Page 161 General General Model Name SyncMaster 540B LCD Panel Size 15 " Diagonal (38 cm) Display area 304.1 mm (H) x 228.1 mm (V) Pixel Pitch 0.297 mm (H) x 0.297 mm (V) Synchronization Horizontal 30 ~ 61 k Hz Vertical 56 ~ 75 Hz Display Color 16.2 M Colors...
Page 162 EPA/ENERGY mode (Power button) Blue, Blinking Less than 1 W Less than 1 W (Off-mode) (120 Vac / 220 Vac) ® Partner, SAMSUNG has determined that this ® Power off 2000 (Power Switch) Black Black Less than 0 W ®...
Page 163 Preset Timing Modes If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows. Table 1.
Page 164 General General Model Name SyncMaster 540N LCD Panel Size 15 " Diagonal (38 cm) Display area 304.1 mm (H) x 228.1 mm (V) Pixel Pitch 0.297 mm (H) x 0.297 mm (V) Synchronization Horizontal 30 ~ 61 k Hz Vertical 56 ~ 75 Hz Display Color 16.2 M Colors...
Page 165 EPA/ENERGY mode (Power button) Blue, Blinking Less than 1 W Less than 1 W (Off-mode) (120 Vac / 220 Vac) ® Partner, SAMSUNG has determined that this ® Power off 2000 (Power Switch) Black Black Less than 0 W ®...
Page 166 Preset Timing Modes If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows. Table 1.
Page 167 General General Model Name SyncMaster 740T LCD Panel Size 17 " Diagonal (43 cm) Display area 337.92 mm (H) x 270.336 mm (V) Pixel Pitch 0.264 mm (H) x 0.264 mm (V) Synchronization Horizontal 30 ~ 81 k Hz Vertical 56 ~ 75 Hz Display Color 16.2 M Colors...
Page 168 (Power button) Blue, Blinking Less than 1 W Less than 1 W (Off-mode) (120 Vac / 220 Vac) ® Partner, SAMSUNG has determined that this Power off 2000 (Power Switch) Black Black Less than 0 W ® compliant and ENERGY2000...
Page 169 product meets the ENERGY STAR Preset Timing Modes If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on.
Page 170 many times per second to display an image to the user. The frequency of this repetition is called the Vertical Frequency or Refresh Rate. Unit: Hz...
Page 171 General General Model Name SyncMaster 940T LCD Panel Size 19 " Diagonal (48 cm) Display area 376.32 mm (H) x 301.056 mm (V) Pixel Pitch 0.294 mm (H) x 0.294 mm (V) Synchronization Horizontal 30 ~ 81 k Hz Vertical 56 ~ 75 Hz Display Color 16.7 M Colors...
Page 172 (Power button) Blue, Blinking Less than 1 W Less than 1 W (Off-mode) (120 Vac / 220 Vac) ® Partner, SAMSUNG has determined that this Power off 2000 (Power Switch) Black Black Less than 0 W ® compliant and ENERGY2000...
Page 173 product meets the ENERGY STAR Preset Timing Modes If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on.
Page 174 many times per second to display an image to the user. The frequency of this repetition is called the Vertical Frequency or Refresh Rate. Unit: Hz...
Page 175 General General Model Name SyncMaster 940N LCD Panel Size 19 " Diagonal (48 cm) Display area 376.32 mm (H) x 301.056 mm (V) Pixel Pitch 0.294 mm (H) x 0.294 mm (V) Synchronization Horizontal 30 ~ 81 k Hz Vertical 56 ~ 75 Hz Display Color 16.7M Colors...
Page 176 407.6 x 408.0 x 200.0mm / 16.0 x 16.1 x 7.9 inch (with Basic Stand) / 5.55 kg Dimensions (WxHxD)/ Weight (Sliding Stand) 407.6 x 408.0 x 200.0mm / 16.0 x 16.1 x 7.9 inch (with Basic Stand) / 5.7 kg Dimensions (WxHxD)/ Weight (Lowest HAS Stand) 407.6 x 368.2 x 200.0 mm / 16.0 x 14.5 x 7.9 inch (with Basic Stand) / 5.8 kg VESA Mounting Interface...
Page 177 Horizontal Cycle is called the Horizontal Frequency. Unit: kHz Vertical Frequency Like a fluorescent lamp, the screen has to repeat the same image ® Partner, SAMSUNG has determined that this ® guidelines for energy efficiency. Vertical Pixel Clock...
Page 178 many times per second to display an image to the user. The frequency of this repetition is called the Vertical Frequency or Refresh Rate. Unit: Hz...
Page 179 General General Model Name SyncMaster 940Be LCD Panel Size 19 " Diagonal (48 cm) Display area 376.32 mm (H) x 301.056 mm (V) Pixel Pitch 0.294 mm (H) x 0.294 mm (V) Synchronization Horizontal 30 ~ 81 k Hz Vertical 56 ~ 75 Hz Display Color 16.7 M Colors...
Page 180 EPA/ENERGY mode (Power button) Blue, Blinking Less than 1 W Less than 1 W (Off-mode) (120 Vac / 220 Vac) ® Partner, SAMSUNG has determined that this ® Power off 2000 (Power Switch) Black Black Less than 0 W ®...
Page 181 Preset Timing Modes If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows. Table 1.
Page 182 Contact SAMSUNG WORLDWIDE If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center. U.S.A 1-800-SAMSUNG (7267864) CANADA 1-800-SAMSUNG (7267864) MEXICO 01-800-SAMSUNG (7267864) ARGENTINE 0800-333-3733 BRAZIL 4004-0000 CHILE 800-726-7864 (SAMSUNG) COLOMBIA 01-8000112112 COSTA RICA...
Page 183 09 693 79 554 FRANCE 08 25 3260 (€ 0,15/min) GERMANY 01805 - 121213 (€ 0,14/Min) HUNGARY 06-80-SAMSUNG (7267864) ITALIA 800 SAMSUNG (7267864) LUXEMBURG 02 261 03 710 NETHERLANDS 0900 20 200 88 (€ 0,10/Min) NORWAY 231 627 22 POLAND...
Page 184 THAILAND 1800-29-3232, 02-689-3232 TAIWAN 0800-329-999 VIETNAM 1 800 588 889 SOUTH AFRICA 0860 7267864 (SAMSUNG) 800SAMSUNG (7267864) U.A.E 8000-4726 Terms Dot Pitch The image on a monitor is composed of red, green and blue dots. The closer the dots, the higher the resolution.
Page 185 Reproduction in any manner whatsoever without the written permission of Samsung Electronics Co., Ltd. is strictly forbidden. Samsung Electronics Co., Ltd. shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.
Page 186 MÉXICO IMPORTADO POR: SAMSUNG ELECTRONICS MÉXICO. S.A. de C.V. Vía Lopez Portillo No. 6, Col. San Fco. Chilpan Tultitlán, Estado de México, C.P. 54940 Tel: 01-55-5747-5100 / 01-800-726-7864 EXPORTADO POR: Samsung Electronics CO.,LTD. 416, Mae tan-3dong, Yeongtong - gu, Suwon City, Gyeonggi-do Korea...
Page 187 PRODUCT INFORMATION (Image Retention Free) LCD Monitors and TVs may have image retention when switching from one image to another especially after displaying a stationary image for a long time. This guide is to demonstrate correct usage of LCD products in order to protect them from Image retention.
Page 188 The best way to protect your monitor from Image retention is to set your PC or System to operate a Screen Saver program when you are not using it. Image retention may not occur when a LCD panel is operated under normal conditions. Normal conditions are defined as continuously changing video patterns.
Page 189 Correct Disposal of This Product (Waste Electrical & Electronic Equipment) - Europe only (Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life.

This manual is also suitable for:

Syncmaster 540b Syncmaster 740b Syncmaster 740n Syncmaster 740t 910t Syncmaster 940b ... Show all

Samsung SyncMaster 540N User Manual

Quick Links

Related Manuals for Samsung SyncMaster 540N

Summary of Contents for Samsung SyncMaster 540N

Page 37: Connecting The Monitor

Page 38: Using The Stand

Page 104: System Requirements

Page 113: Color Calibration

Page 116: Troubleshooting

Page 123: Installation Problems

Page 131: Check List

This manual is also suitable for:

Table of Contents