Edirol V-4CF Owner's Manual

Cross fader

page of 1

/ 1
Bookmarks

Quick Links

Download this manual

V-4 Cross Fader Owner's Manual

Before using this unit, carefully read the sections entitled: ''USING THE UNIT SAFELY'' and ''IMPORTANT NOTES'' .

These sections provide important information concerning the proper operation of the unit. Additionally, in order to feel

assured that you have gained a good grasp of every feature provided by your new unit, Owner's Manual should be read

in its entirety. The manual should be saved and kept on hand as a convenient reference.

Installing the Cross Fader

1. Switch off the power to the V-4.

2. Using a Phillips screwdriver, remove the screws at the four corners of the video fader (Fig. 1).

3. Turn the video fader upside-down and detach the cable connecting the V-4 to the video fader.

The cable is held in place by a hook on the video fader. Detach the cable from the hook (Fig. 2), then

disconnect the connector on the video fader (Fig. 2).

When reinstalling the video fader, orient the connector as shown in the figure and insert it. After attaching the connector,

secure the cable in place on the hook.

Portions of the connector for the video fader are sharp. When unplugging or inserting the connector, be careful not to get

your hands cut.

4. Orient the connector as shown in the figure and insert it into the cross fader (Fig. 4).

Never use excessive force to insert the connector. If it won't go in properly, pull it out and try again.

5. Attach the cross fader using the screws you removed in step 2 (Fig. 5).

Orient the cross fader by aligning the triangle printed on the cross fader with the triangle printed on the V-4 (Fig. 6).

After you have completed the installation procedure, check again to make sure the device is installed correctly.

When the installation is finished, carry out the procedure described in "Adjusting the V-4" below.

Overtightening the screws may damage the unit's case. Roland assumes no responsibility for any accident or product

damage arising from installation operations.

No Phillips screwdriver is included with this product.

(Fig.1)

(Fig.4)

962a

In the interest of product improvement, the specifications and/or appearance of this unit are subject tochange without

prior notice.

202

Used for instructions intended to alert

the user to the risk of death or severe

injury

should

the

unit

improperly.

Used for instructions intended to alert

the user to the risk of injury or material

damage should the unit be used

improperly.

* Material damage refers to damage or

other adverse effects caused with

respect to the home and all its

furnishings, as well to domestic

animals or pets.

001

• Before using this unit, make sure to read the instruc-

tions below, and the Owner's Manual.

.....................................................................................................................................................................................................................................

002a

• Do not open or perform any internal modifications on

the unit.

002 ex

• Do not open or perform any internal modifications on

the cross fader unit.

003

• Do not attempt to repair the unit, or replace parts

within it (except when this manual provides specific

instructions directing you to do so). Refer all servicing

to your retailer, the nearest Roland Service Center, or

an authorized Roland distributor, as listed on the

"Information" page.

014

• Protect the unit from strong impact.

(Do not drop it!)

022c

• Before installing the cross fader unit, you must first

always turn off the V-4 and unplug its power cord.

106

• Never climb on top of, nor place heavy objects on the

unit.

118a

• Should you remove screw, keep them in a safe place

out of children's reach, so there is no chance of them

being swallowed accidentally.

.......................................... IMPORTANT NOTES ..............................................

291a

• In addition to the items listed under "USING THE UNIT SAFELY" , please read and observe the following:

354a

• Do not expose the unit to direct sunlight, place it near devices

that radiate heat, leave it inside an enclosed vehicle, or

otherwise subject it to temperature extremes. Excessive heat

can deform or discolor the unit..

355b

• When moved from one location to another where the temper-

ature and/or humidity is very different, water droplets

(condensation) may form inside the unit. Damage or

malfunction may result if you attempt to use the unit in this

condition. Therefore, before using the unit, you must allow it

to stand for several hours, until the condensation has

completely evaporated.

401a

• For everyday cleaning wipe the unit with a soft, dry cloth or

one that has been slightly dampened with water. To remove

stubborn dirt, use a cloth impregnated with a mild, non-

abrasive detergent. Afterwards, be sure to wipe the unit

thoroughly with a soft, dry cloth.

402

• Never use benzine, thinners, alcohol or solvents of any kind,

to avoid the possibility of discoloration and/or deformation.

(Fig.2)

(Fig.3)

A A

B B

(Fig.5)

(Fig.6)

03901734

The

symbol alerts the user to important instructions

or warnings.The specific meaning of the symbol is

determined by the design contained within the

used

triangle. In the case of the symbol at left, it is used for

general cautions, warnings, or alerts to danger.

The

symbol alerts the user to items that must never

be carried out (are forbidden). The specific thing that

must not be done is indicated by the design contained

within the circle. In the case of the symbol at left, it

means that the unit must never be disassembled.

●

The

symbol alerts the user to things that must be

carried out. The specific thing that must be done is

indicated by the design contained within the circle. In

the case of the symbol at left, it means that the power-

cord plug must be unplugged from the outlet.

004

• Never use or store the unit in places that are:

•

Subject to temperature extremes (e.g., direct sunlight in an

enclosed vehicle, near a heating duct, on top of heat-gener-

ating equipment); or are

•

Damp (e.g., baths, washrooms, on wet floors); or are

•

Humid; or are

•

Exposed to rain; or are

•

Dusty; or are

•

Subject to high levels of vibration.

011

• Do not allow any objects (e.g., flammable material,

coins, pins); or liquids of any kind (water, soft drinks,

etc.) to penetrate the unit.

013

• In households with small children, an adult should

provide supervision until the child is capable of

following all the rules essential for the safe operation of

the unit.

105b

• If the unit could become a hazard if it moves, all caster

wheels should be removed once the unit has been

placed at the place of installation, or has been loaded

onto a vehicle.

added

• The subsequent performance of the unit cannot be assured

after the user has subjected the cross fader to any form of

disassembly or modification.

553

• Use a reasonable amount of care when using the unit's sliders

and other controls. Rough handling can lead to malfunctions.

556

• When connecting or disconnecting any cable, grasp the

connector itself---never pull on the cable. That way, you will

avoid causing shorts or damage to the cable's internal

elements.

559c added

• Dispose of the packing carton and padding for this device in

accordance with your local standards for sorting refuse.

added

• The cross fader is a consumable item. Replacement is possible

only in the event of initial failure due to a manufacturing

defect.

added

• Exercise caution to prevent injury to the hands around the

openings through which installations are performed, and on

the edges of circuit boards.

Adjusting the V-4

The V-4 requires adjustment whenever the cross fader is replaced or the stroke is adjusted.

1. Connect the PREVIEW OUT jack on the V-4 to a television monitor (Fig. 1).

2. Turn on the power to the V-4. A light comes on in the gap with the cross fader.

3. Press the MENU button. The Menu screen appears on the television monitor (Figs. 2).

As you carry out the operation described below, view the television monitor connected to the PREVIEW OUT jack.

4. Press the [ ] or [ ] button to move the cursor to "Utility," then press the ENTER button.

5. Press the [ ] or [ ] button to select "Video Fader Calibrate A," then press the ENTER button.

Move the control for the cross fader all the way to A, then press the ENTER button .

6. Press the [ ] or [ ] button to select "Video Fader Calibrate B," then press the ENTER button.

Move the control for the cross fader all the way to B, then press the ENTER button.

7. Press the MENU button twice to quit the Menu screen.

(Fig. 1) PREVIEW OUT jack

Adjustment similar to that just described is also required whenever the video fader is replaced.

Connector

■ Adjusting the Stroke

You can adjust the cross fader to a stroke at any of four stages (10 mm, 23 mm, 35 mm, and 45 mm).

If the cross fader is installed on the V-4 unit, detach it before you carry out the operation described below.

1. Move the control for the cross fader to its central position.

2. Using a Phillips screwdriver, remove the stopper retainer screw (Fig. 1).

Move the stopper to any one of the four holes that you prefer (Fig. 2).The four stopper holes are stamped

"10," "23," "35," and "45." These indicate the stroke obtained when screwed to the respective hole. Use these

stamped indicators as a guide for positioning the stopper.

3. Secure the stopper in place using the stopper retainer screw you removed in step 2 (Fig. 3).

Overtightening the screw may damage the cross fader. Roland assumes no responsibility for any accident or product

damage arising from installation operations.

No Phillips screwdriver is included with this product.

Never remove any screw other than the one specified.

'05-1-1N

Information

When you need repair service, call your nearest EDIROL/Roland Service Center or authorized EDIROL/Roland distributor

in your country as shown below.

EUROPE

EDIROL (Europe) Ltd.

Studio 3.4 114 Power Road

London W4 5PY

U. K.

TEL: +44 (0)20 8747 5949

FAX:+44 (0)20 8747 5948

http://www.edirol.com/europe

ASIA

TAIWAN

ROLAND TAIWAN

ENTERPRISE CO., LTD.

Room 5, 9fl. No. 112 Chung Shan

N.Road Sec.2, Taipei, TAIWAN,

R.O.C.

TEL: (02) 2561 3339

CHINA

Roland Shanghai Electronics Co.,Ltd.

5F. No.1500 Pingliang Road

Shanghai 200090, CHINA

TEL: (021) 5580-0800

Roland Shanghai Electronics Co.,Ltd.

(BEIJING OFFICE)

10F. No.18 Anhuaxili

Chaoyang District, Beijing 100011

CHINA

TEL: (010) 6426-5050

Roland Shanghai Electronics Co.,Ltd.

(GUANGZHOU OFFICE)

2/F., No.30 Si You Nan Er Jie Yi

Xiang, Wu Yang Xin Cheng,

Guangzhou 510600, CHINA

TEL: (020) 8736-0428

AUSTRALIA

Roland Corporation

Australia Pty., Ltd.

38 Campbell Avenue

Dee Why West. NSW 2099

AUSTRALIA

TEL: (02) 9982 8266

(Fig. 2) MENU button, [ ] and [ ] buttons,

and ENTER button

Stopper retainer screw

Stopper

(Fig.1)

(Fig.2)

U. S. A. / CANADA

EDIROL Corporation

Deutschland

North America

TEL: 0700 33 47 65 20

425 Sequoia Drive, Suite 114

France

Bellingham, WA 98226

TEL: 0810 000 371

U. S. A.

Italia

TEL: (360) 594-4273

TEL: 02 93778329

FAX: (360) 594-4271

http://www.edirol.com/

CZECH REP.

CENTRAL/LATIN

K-AUDIO

AMERICA

Kardasovska 626.

CZ-198 00 Praha 9,

CZECH REP.

BRAZIL

TEL: (2) 666 10529

Roland Brasil Ltda

Rua San Jose, 780 Sala B

DENMARK

Parque Industrial San Jose

Roland Scandinavia A/S

Cotia - Sao Paulo - SP, BRAZIL

Nordhavnsvej 7, Postbox 880,

TEL: (011) 4615 5666

DK-2100 Copenhagen

DENMARK

OTHERS incl. MEXICO

TEL: 3916 6200

Roland Audio Development

Corp.

FINLAND

14830 Desman Rd.

Roland Scandinavia As,

La Mirada, CA 90638

Filial Finland

U.S.A.

Elannontie 5

Tel: 1-714-521-8000

FIN-01510 Vantaa, FINLAND

email : sales@rolandaudio.com

TEL: (0)9 68 24 020

GERMANY

EUROPE

Roland Elektronische

Musikinstrumente HmbH.

AUSTRIA

Oststrasse 96, 22844 Norderstedt,

GERMANY

Roland Elektronische

TEL: (040) 52 60090

Musikinstrumente HmbH.

Austrian Office

GREECE

Eduard-Bodem-Gasse 8,

STOLLAS S.A.

A-6020 Innsbruck, AUSTRIA

Music Sound Light

TEL: (0512) 26 44 260

155, New National Road

Patras 26442, GREECE

BELGIUM/FRANCE/

TEL: 2610 435400

HOLLAND/

HUNGARY

LUXEMBOURG

Roland Central Europe N.V.

Roland East Europe Ltd.

Houtstraat 3, B-2260, Oevel

Warehouse Area 'DEPO' Pf.83

(Westerlo) BELGIUM

H-2046 Torokbalint, HUNGARY

TEL: (014) 575811

TEL: (23) 511011

(Fig. 3) Video Fader Calibrate

Stopper retainer sc

(Fig.3)

IRELAND

RUSSIA

Roland Ireland

MuTek

G2 Calmount Park, Calmount

3-Bogatyrskaya Str. 1.k.l

Avenue, Dublin 12

107 564 Moscow, RUSSIA

Republic of IRELAND

TEL: (095) 169 5043

TEL: (01) 4294444

SPAIN

ITALY

Roland Iberia, S.L.

Roland Italy S. p. A.

Paseo García Faria, 33-35

Viale delle Industrie 8,

08005 Barcelona SPAIN

20020 Arese, Milano, ITALY

TEL: 93 308 10 00

TEL: (02) 937-78300

SWEDEN

NORWAY

Roland Scandinavia A/S

Roland Scandinavia Avd.

SWEDISH SALES OFFICE

Kontor Norge

Danvik Center 28, 2 tr.

Lilleakerveien 2 Postboks 95

S-131 30 Nacka SWEDEN

Lilleaker N-0216 Oslo

TEL: (0)8 702 00 20

NORWAY

TEL: 2273 0074

SWITZERLAND

Roland (Switzerland) AG

POLAND

Landstrasse 5, Postfach,

MX MUSIC SP.Z.O.O.

CH-4452 Itingen,

UL. Gibraltarska 4.

SWITZERLAND

PL-03664 Warszawa POLAND

TEL: (061) 927-8383

TEL: (022) 679 44 19

UKRAINE

PORTUGAL

TIC-TAC

Roland Iberia, S.L.

Mira Str. 19/108

Portugal Office

P.O. Box 180

Cais das Pedras, 8/9-1 Dto

295400 Munkachevo, UKRAINE

4050-465, Porto, PORTUGAL

TEL: (03131) 414-40

TEL: 22 608 00 60

UNITED KINGDOM

ROMANIA

Roland (U.K.) Ltd.

FBS LINES

Atlantic Close, Swansea

Piata Libertatii 1,

Enterprise Park, SWANSEA

SA7 9FJ,

535500 Gheorgheni, ROMANIA

UNITED KINGDOM

TEL: (266) 364 609

TEL: (01792) 702701

As of August 20, 2004

(EDIROL-2)

This manual is also suitable for:

V-4

Edirol V-4CF Owner's Manual

Quick Links

.......................................... IMPORTANT NOTES ..............................................

Related Manuals for Edirol V-4CF

Related Products for Edirol V-4CF

This manual is also suitable for: