Sign in today to find solutions:

Don't have an account? Sign up

RCA RS2664 User Manual

Rca rs2664 stereo systems: user manual.

Tocom: 5645 6830
user manual
manual de usuario
RS2664
EN/E
It is important to read this instruction prior to using your new product for the first time.
Es importante leer este manual antes de usar por vez primera su euipo.
Getting started
Connecting main speakers
Unpacking the system
You should have the following:
Each speaker has a black/red wire and a black/
one main unit (with 2 main speakers)
purple wire. When connecting the speakers,
one remote control
match the red/purple wires to the red/purple
one AM loop antenna
jacks and the black wires to the black jacks on
one user manual
the main unit.
owner registration card
Speaker Wire Connection
Back view
1. Main speaker jacks (high pass)
2. Woofer jacks (low pass)
3. AM loop antenna jack
4. FM pigtail antenna
Push Speaker terminal tab
Release tab to lock wire in
down to insert wire.
the terminal.
NOTE: Make sure the insulation is completely removed from the
ends of the speaker wires at all connection points.
1
4
3
2
Installation
To ensure sufficient ventilation, keep the spacing
shown as below:
Using FM and AM antennas
4"
4"
Before you use your audio system, you'll want to
make sure both the FM and AM antennas are
positioned properly. Uncoil the FM antenna at
the back of the unit, making sure it is fully
4"
2"
4"
extended (you may even want to tape it to the
wall behind the unit if possible, the higher the
better). You'll also need to connect the AM
antenna loop to the back of the unit if you
listen to AM stations. Rotate the AM loop
antenna for better reception.
Front view
Side view
Display
BASS – bass boost activated
SLEEP – sleep mode activated
CD tray status:
REC – recording in progress
Lights when loaded
PROG – program playback
Flashes for the current disc
mode activated
Animates when playing
Source indication
SLEEP
REPEAT
REC PROG
File
1ALL
format
DISCS
ST
Radio
INTRO
bands
Folder
Timer
Playback
activated
navigation
mode
mode
status
FM stereo mode activated
Adjusting display brightness
Press and hold DEMO/DIMMER to adjust the
display brightness.
Showing demonstration
Press DEMO/DIMMER to turn on or off the
demonstration mode. The demonstration scrolls
through all display operations.
Disc and USB playback
Information display
Track/folder selection
In mp3/wma disc mode, press BAND/INFO on the
1. Press
/
to skip to the previous or
main unit repeatedly during playback to show
next track.
the ID3 tag information (e.g. song title, artist,
2. Press and hold
/
to search through
album).
a track while it is playing.
When the mp3/wma disc is fully stopped, press
3. For USB, mp3/wma disc, press
to view the Folders Total (FT) and Track
FOLDER/PRESET
/
(or PREV/NEXT on
Total (TT) on the current disc.
the main unit) to skip to the previous or
next folder.
In USB mode, press BAND/INFO on the main unit
to view used (U) and free (F) memory on the USB
device.
You can use
/
or
FOLDER/PRESET
/
to select a
track when playback is stopped.
When a track is selected (with track
number/name shows on the display), press
within 10 seconds to start the playback.
Radio
Accessing preset stations
Press SOURCE repeatedly to enter the tuner
mode.
Press PREV/NEXT on the main unit or
FOLDER/PRESET
/
on the remote control
Selecting tuner band
to access the previous or next preset station. The
Press BAND/INFO (or BAND/REPEAT on the
PROG icon lights up when a preset station is
remote control) to select between the FM or
selected. The display first shows the preset
AM radio band.
program number and after a few seconds, the
radio frequency will be displayed.
Tuning to a station
Suppressing stereo signal
Press
/
to adjust frequencies. Press and
hold to start auto seaching for the next available
Press FM ST/INTRO on the remote control to
select between the FM mono and stereo modes.
station.
"ST" is displayed in the stereo mode.
Manually setting presets
1. Press
/
to access the desired
frequency.
2. Press PROG/SET once. The most recently
accessed program location will be displayed.
3. If a different program location is preferred,
press
/
on the remote control to
move to the desired preset number (1-32).
4. Press PROG/SET to store the selected
frequency at that preset.
Auto preset programming
(FM only)
Press and hold BAND/INFO (BAND/REPEAT on
the remote control) for 2 seconds to scan
stations in the FM band. The stations will then
be stored as preset channels. A maximum of 32
stations can be stored.
Beware of your preset channels being erased
accidentally because the scanning and storing
process is automatic upon pressing the button.
You can stop the automatic scan by pressing any
button, but the erased stations cannot be
recovered.
Note
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
FCC information
For your safety
This device complies with Part 15 of the FCC
The AC power plug is polarized
Rules. Operation is subject to the following two
(one blade is wider than the
conditions: (1) This device may not cause harmful
other) and only fits into AC power
interference, and (2) this device must accept any
outlets one way. If the plug won't
interference received, including interference
go into the outlet completely, turn
that may cause undesired operation.
the plug over and try to insert it
In accordance with FCC requirements, changes or
the other way. If it still won't fit, contact a
modifications not expressly approved by
qualified electrician to change the outlet, or use
Thomson Inc. could void the user's authority to
a different one. Do not attempt to bypass
operate this product.
this safety feature.
This device generates and uses radio frequency
(RF) energy, and if not installed and used
CAUTION: TO PREVENT ELECTRIC SHOCK,
properly, this equipment may cause interference
MATCH WIDE BLADE OF PLUG TO WIDE SLOT,
to radio and television reception.
FULLY INSERT.
If this equipment does cause interference to
radio or television reception (which you can
determine by turning the equipment off and
CAUTION
RISK OF ELECTRIC SHOCK
on), try to correct the interference by one or
DO NOT OPEN
more of the following measures:
T H E
L I G H T N I N G
CAUTION: TO REDUCE THE
THE EXCLAMATION
Reorient the receiving antenna (that is, the
FLASH AND ARROW-
RISK OF ELECTRIC SHOCK,
POINT WITHIN THE
HEAD WITHIN THE
D O N O T R E M O V E C O V E R
T R I A N G L E I S A
antenna for the radio or television that is
T R I A N G L E I S
A
( O R B A C K ) . N O U S E R -
WARNING
SIGN
W A R N I N G
S I G N
S E RV I C E A B L E PA R T S I N -
ALERTING YOU OF
"receiving" the interference).
ALERTING YOU OF
S I D E . R E F E R S E RV I C I N G
I M P O R T A N T
Move the unit away from the equipment
" D A N G E R O U S
I N S T R U C T I O N S
T O Q U A L I F I E D S E R V I C E
VOLTAGE" INSIDE
PERSONNEL.
A C C O M PA N Y I N G
that is receiving interference.
THE PRODUCT.
T H E
P R O D U C T.
Plug the unit into a different wall outlet so
SEE MARKING ON BOTTOM / BACK OF PRODUCT
that the unit and the equipment receiving
interference are on different branch circuits.
WARNING:
TO PREVENT FIRE OR ELECTRICAL
If these measures do not eliminate the
SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT
TO RAIN OR MOISTURE.
interference, please consult your dealer or an
experienced radio/television technician for
additional suggestions.
Also, the Federal Communications Commission
has prepared a helpful booklet, "How To
Identify and Resolve Radio TV Interference
Problems." This booklet is available from the
This audio system has
earned the ENERGY STAR.
U.S. Government Printing Office, Washington,
DC 20402. Please specify stock number 004-000-
00345-4 when ordering copies.
This product complies with DHHS Rules 21 CFR
Subchapter J. Applicable at the date of
manufacture.
General controls
Main unit
GEFAHR EINES
ELEKTRISCHEN SCHLAGS
BAND/INFO
ON/STANDBY – to turn on or off (standby
in CD mode, to select among the playback
mode) the unit. Remember to unplug the power
cord from the power outlet if you are not going
information.
in USB mode, to show the memory usage.
to use the system for some time.
in mp3/wma disc mode, to show the track
SOURCE – to select among the CD player, Tuner,
play time and ID3 tags information (e.g.
AUX and USB modes.
song title, artist, album) during playback.
in tuner mode, to use as BAND key to
change among the tuner bands. To enter
CD REC – to start and stop recording from CD to
the USB device.
the auto preset programming in the FM
mode when pressed for 2 seconds.
USB jack – to connect the USB device.
Mass Storage Class (MSC) devices are supported.
BASS BOOST – to turn on or off the Bass Boost.
Clock/Timer/Sleep timer
Setting the clock
Sleep mode
1. Press and hold CLOCK on remote control
You can select the time interval in minutes
until the hour flashes on the display.
before the unit turns off automatically.
2. Press
/
to set the hour and then
Press SLEEP to select among OFF, 120, 90, 60, 45,
press CLOCK to shift to the minute digits.
30, 15 and 5 minutes. The SLEEP icon lights on
the display when sleep mode is activated.
3. Press
/
to set the minute.
4. Press CLOCK to save the setting or
to
View remaining sleep time
quit setting without saving.
When sleep mode is activated, press SLEEP once
to view the remaining sleep time.
When the unit is turned on, you
Adjust sleep time
can press CLOCK to display the
Press SLEEP again when the remaining sleep
current time for about 4 seconds.
time is displayed to change the sleep time.
Sleep mode is automatically de-activated when
the unit is turned off.
Setting the timer
1. Press and hold TIMER on the remote
control until "ON" and the clock hour
flashes on the display (ON - timer on time ).
2. To set the timer on time, press
/
to
set the hour and then press TIMER to shift
to minute digits.
3. Press
/
to set the minute.
4. Press TIMER to change to OFF (timer off
time) with clock time flashing. Repeat steps
2 & 3 for the timer off time setting.
5. Press TIMER to select source. Press
/
to select among TUNER, DISC or USB.
6. Press TIMER to set the volume. Adjust
VOLUME on the main unit or press VOL +/–
or
/
on the remote control to
select the desired volume level.
7. Press TIMER on the remote control to save
and quit the settings. The timer is
automatically activated once timer setting is
saved.
Activating the timer
Press and release TIMER to turn on or off the
timer. The timer icon is displayed when the timer
is activated.
Disc and USB playback
Playback sequence of disc
Check that the mp3/wma disc is created with a single folder structure. Refer to the diagram
below for playback sequence details on multi-level folder structure.
For example, folders and songs from level 2 are played before moving on to play folders and
songs from level 3.
Folder playback sequence is indicated by the letters A to G.
Song playback sequence is indicated by the numbers (1 to 15) in front of the song name.
LEVEL 1
LEVEL 2
LEVEL 3
LEVEL 4
A
D
Folder 1.1
Folder 1
8
Song 1.1.1
9
Song 1.1.2
10
Song 1.1.3
E
G
Folder 1.2
Folder 1.2.1
13
Song 1.2.1.1
14
Song 1.2.1.2
15
Song 1.2.1.3
B
F
Folder 2
Folder 2.1
11
Song 2.1.1
12
Song 2.1.2
3
Song 2.2
Song 2.3
4
Song 2.4
5
C
Folder 3
6
Song 3.1
7
Song 3.2
1
Song 4
2
Song 5
Troubleshooting tips
CD sound skips
System does not turn on
Check power cord for a secure connection.
Clean the disc.
Unplug the unit for a moment, and then
Check disc for warping, scratches, or other
damages.
plug it back in.
Check if something is causing the system to
Check the outlet by plugging in another
device.
vibrate. If so, move the system.
Make sure the speakers are at least 3 feet
away or on a different surface from the
There is no sound
Increase the volume setting.
main unit.
Check connection to speakers.
CD button does not respond, or does not change
Check that you have selected the
discs when you press DISC SKIP
appropriate function: CD, Tuner or Aux.
Make sure mute is off.
Switch to another function (Tuner) and
Make sure headphones are not plugged in.
then back to CD.
Poor radio reception
Remote control does not work
Check antenna connection.
Check that the batteries are properly
installed.
Move antenna.
Replace weak batteries.
Turn off nearby electrical appliances, such
as hair dryer, vacuum cleaner, microwave
Check that the system is plugged into
oven or fluorescent lights.
power source.
Point the remote directly at the system's
CD does not play
front panel.
Check that CD is in the tray.
Move closer to the system.
Remove any obstacles between the remote
Check that CD label is facing up.
and the system.
Check that PAUSE mode is not on.
Check that CD function is selected.
Use CD lens cleaner.
Clean the disc.
Try another CD.
Note
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
PLEASE READ AND SAVE THIS FOR FUTURE REFERENCE
IMPORTANT SAFETY INSTRUCTIONS
Refer all servicing to qualified service
Some of the following information may not
apply to your particular product; however, as
personnel. Servicing is required when the
with any electronic product, precautions should
apparatus has been damaged in any way,
be observed during handling and use.
such as power-supply cord or plug is
Read these instructions.
damaged, liquid has been spilled or objects
Keep these instructions.
have fallen into the apparatus, the
Heed all warnings.
apparatus has been exposed to rain or
moisture, does not operate normally, or has
Follow all instructions.
Do not use this apparatus near water.
been dropped.
Clean only with dry cloth.
ADDITIONAL SAFETY INFORMATION
Do not block any ventilation openings.
Apparatus shall not be exposed to dripping
Install in accordance with the
or splashing and no objects filled with
manufacturer's instructions.
liquids, such as vases, shall be placed on the
Do not install near any heat sources such as
apparatus.
radiators, heat registers, stoves, or other
Always leave sufficient space around the
apparatus (including amplifiers) that
product for ventilation. Do not place
produce heat.
product in or on a bed, rug, in a bookcase
Do not defeat the safety purpose of the
or cabinet that may prevent air flow
polarized or grounding-type plug. A
through vent openings.
polarized plug has two blades with one
Do not place lighted candles, cigarettes,
wider than the other. A grounding type
cigars, etc. on the product.
plug has two blades and a third grounding
Connect power cord only to AC power
prong. The wide blade or the third prong is
source as marked on the product.
provided for your safety. If the provided
Care should be taken so that objects do not
plug does not fit into your outlet, consult
fall into the product.
Do not attempt to disassemble the cabinet.
an electrician for replacement of the
obsolete outlet.
This product does not contain customer
Protect the power cord from being walked
serviceable components.
on or pinched particularly at plugs,
IF YOUR PRODUCT OPERATES ON
convenience receptacles, and the point
BATTERIES, adhere to the following
where they exit from the apparatus.
precautions:
Only use attachments/accessories specified
A. Any battery may leak electrolyte if mixed
with a different battery type, if inserted\
by the manufacturer.
Use only with the cart,
incorrectly, or if all batteries are not
stand, tripod, bracket, or
replaced at the same time.
table specified by the
B. Any battery may leak electrolyte or
manufacturer, or sold with
explode if disposed of in fire or an attempt
the apparatus. When a
is made to charge a battery not intended to
cart is used, use caution
be recharged.
when moving the cart/
C. Discard leaky batteries immediately.
apparatus combination to avoid injury from
Leaking batteries can cause skin burns or
tip-over.
other personal injury. When discarding
Unplug this apparatus during lightning
batteries, be sure to dispose of them in the
proper manner, according to your state/
storms or when unused for long periods of
time.
provincial and local regulations.
General controls
DEMO/DIMMER – to activate or deactivate the
PREV/NEXT
display demostration. Press and hold to adjust
in USB or mp3/wma disc mode, to go to the
the display brightness.
previous or next folder.
in tuner mode, to select the previous or
– to open or close the disc tray.
next preset station.
EQ – to select the equalizer presets.
PROG/SET
to enter the program mode for CD, USB
and tuner.
in USB mode, to enter the file rename
operation.
VOLUME – to adjust the volume.
Phone and AUX IN
DISC 1/2/3/4/5 – to enter the CD mode and play
Open the compartment door at the bottom of
the corresponding CD.
the main unit to reveal the jacks inside.
PHONE - Jack for connecting headphones.
– in CD, USB or mp3/wma disc mode, to
AUX IN - Jacks for external sound input.
start and pause the playback.
in CD, USB or mp3/wma disc mode, to stop
the playback.
in mp3/wma disc mode, to return to the
first track of the current disc; to display the
total number of folders and total number
of tracks on the current disc when playback
is completely stopped.
in recording mode, to stop recording to the
USB device.
/
in CD, USB or mp3/wma disc mode, to go to
the previous or next track; press and hold
to search backward or forward within a
track.
in tuner mode, to tune down or up the
radio frequency.
Sound control
Volume control
Adjust VOLUME on the main unit or press
VOL +/– on the remote control to adjust the
volume level. The volume level shows briefly on
the display to show the change in the volume
level.
Muting audio
Press
on the remote control to cut the
sound. Press again to restore the sound.
Bass boost
Press BASS BOOST to turn boosting the bass
frequency on or off . The "Bass" icon lights on
the display when it is activated.
Using preset equalizer curves
Press EQ on the remote control to select among
FLAT, ROCK, POP, JAZZ, CLASSIC and CUSTOM.
The display shows your selection briefly.
Creating a Custom Curve
1. Press EQ on the remote control to select
the CUSTOM mode.
2. While CUSTOM is displayed, press
/
to cycle among the displayed bass- and
treble-range levels.
3. While BAS or TRE is displayed, adjust the
volume to set the associated gain between -
10 - +10.
4. Press EQ to exit.
Intro/Repeat/Random playback
Sampling tracks
Press INTRO on the remote control to play the
• The first 99 tracks of each disc
first 10 seconds of each track on the current disc,
will be shuffled and played once
all discs in the tray, or turn the intro mode off.
before any of them is repeated.
The INTRO icon is displayed when sampling is
Random playback can be activated
activated.
simultaneously with repeat 1 disc
(randomly play tracks from one disc
Repeat
repeatedly) or repeat all discs (randomly
Press BAND/REPEAT on the remote control to
play tracks from all discs repeatedly).
repeat the current track (REPEAT 1), current disc
(REPEAT 1 DISC) , all discs (REPEAT ALL DISCS), or
turn repeat mode off (ALL DISCS).
Random playback
Press
on the remote control to turn on or off
the random playback. The
icon is displayed
when it is activated.
All the tracks on one disc will be shuffled and
played once before shuffling and playing tracks
from the next disc.
Maintenance
CD lens care
Disconnect the audio system from the power
source before performing any maintenance.
When your CD lens gets dirty it can also cause
the system to output poor sound quality. To
Cleaning
clean the lens you will need to purchase a CD
Clean the exterior of the system using a soft
lens cleaner which can maintain the output
dust cloth.
sound quality of your system. For instructions on
cleaning the CD lens, refer to the ones
CD player
accompanying the lens cleaner.
CAUTION! This unit operates with laser and may
Technical specifications
only be opened by qualified technicians to avoid
accidents.
Power supply: 120V~60Hz
Dimensions ( H x W x D mm):
Handling CDs
Main unit - 374 x 310 x 495
Speaker - 374 x 286 x 495
Do not touch the recorded surface. Hold
Main unit weight: 7kg
the CD by the perimeter or by the
Speaker weight: 5.8kg
perimeter and the inner edge.
CD player: Response curve (+/- 2dB): 60Hz to
Do not affix labels or adhesive tapes to the
5kHz
label surfaces.
Rating Plate: Refer to the back of the set.
Do not scratch or damage the label. CDs
rotate at high speeds inside the player.
Do not use damaged (cracked or warped)
CDs
Cleaning CDs
Dirty CDs can cause poor sound quality.
Always keep CDs clean by wiping them
gently with a soft cloth from the inner
edge toward the outer perimeter.
If a CD becomes dirty, wipe it clean gently
with a wet, soft cloth. Then wipe dry with
a dry cloth.
Do not use record cleaning sprays or
antistatic agents on CDs. Also, never clean
CDs with benzene, thinner, or other volatile
solvents which may cause damage to disc
surface.
IMPORTADOR
Comercializadora Thomson de México, S.A. de C.V.
Álvaro Obregón No. 151. Piso 13.
Col. Roma. Delegación Cuauhtémoc
C.P. 06700. México, D.F.
Telefono: 52-55-11-020360
RFC: CTM-980723-KS5
EXPORTER
Thomson Inc.
P.O. Box 1976
Indianapolis, IN 46206 - 1976
©2007 Thomson Inc.
Trademark(s) ® Registered
Marque(s) ® Deposée(s)
Marca(s) ® Registrada(s)
www.rcaaudiovideo.com
Printed in China / Impreso en China
Important information
English
Technical information
Safety precautions
Product: Audio System
Never open the cabinet under any
circumstances. Any repairs or internal
Brand: RCA
adjustments should be made only by a
Model: RS2664
trained technician.
Electrical consumption
Never operate this product with the cabinet
removed.
Power Supply: 120V ~ 60Hz
Do not use your System immediately after
Power Consumption: 240 Watts
transporting it from a cold place to a warm
place, as condensation may cause the system
For your records
to malfunction.
In the event that service should be required, you
Keep your unit away from humid areas and
may need the model number. In the space
abnormally hot places.
below, record the date and place of purchase:
Do not touch the player with wet hands. If
Model No.
any liquid enters the player cabinet, take
Date of Purchase
the player to a trained technician for
Place of Purchase
inspection.
This compact disc player uses a laser to read
Service information
the music on the disc. The laser mechanism
This product should be serviced only by those
corresponds to the cartridge and stylus of a
specially trained in appropriate servicing
record player. Although this product
techniques. For instructions on how to obtain
incorporates a laser pick-up lens, it is
service, refer to the warranty included in this
completely safe when operated according to
Guide.
directions.
Discs rotate at high speed inside the player.
Do not use damaged, warped, or cracked
discs.
Do not touch the pick-up lens which is
located inside the disc compartment. To
keep dust from collecting on the pick-up
lens, do not leave the compartment door
open for an extended period of time. If the
lens becomes dirty, clean it with a soft
brush, or use an air blower brush designed
for camera lenses.
The apparatus shall not be exposed to
dripping and splashing and that no objects
filled with liquids, such as vases, shall be
placed on apparatus.
Main plug is used as the disconnet device, it
shall remain operable and should not be
obstructed during intended use. To be
completely disconnected the apparatus from
supply mains, the main plug of the
apparatus shall be disconnected from the
mains socket outlet completely.
General controls
Remote control
SOURCE – to select among the CD player,
Tuner, AUX and USB modes.
– to mute the audio output.
DEL
DEL
ADD
when reviewing the program, to remove
track / file from the program list.
in USB mode, to remove file from the
connected USB device.
in USB mode, to delete the current alphabet
during file rename.
VOL
ADD – in CD, USB or mp3/wma disc mode, to
add tracks to the program list.
– to turn the power on or off (STANDBY
mode).
VOL
EQ – to select the equalizer presets.
PROG/SET
STOP
B.BOOST – to turn on or off the Bass Boost.
BAND/REPEAT
DISC SKIP – to skip to the next disc in CD mode.
CLOCK
SLEEP
/
in CD, USB or mp3/wma disc mode, to go to
FOLDER
CD REC
the previous or next track; press and hold to
/PRESET
search backward or forward within a track.
in tuner mode, to tune down or up the
radio frequency.
The remote control must be
– in CD, USB or mp3/wma disc mode, to
inserted with 2 "AAA" or "UM-4"
start and pause the playback.
or "R03" batteries prior to use.
VOL +/– – to increase or decrease the volume
level.
Disc and USB playback
Important CD and mp3/wma
information
Notes on mp3/wma Disc:
• Use .mp3 as the extension
This unit is compatible with CD-RW/
when converting audio files
CD-R / RW
into mp3 for saving onto CD-R/
CD-R discs for playback.
RW, e.g. Abc08.mp3. Do not use any
other extension e.g. .doc, .pdf.
Do not use the .mp3 extension for
other text or non-audio data files as
Notes on CD-R/RW Disc:
this may result in serious malfunction
• Do not affix any type of labels
and harmful noise interference.
to either side (recordable or
For better quality in mp3/wma disc
labeled side) of a CD-R/ RW disc as this
playback, the CD quality should be
may result in malfunction.
recorded 128kbps or above.
To avoid damages to the CD-R/RW
Disc data size > 650MB is not
disc, do not open the disc
recommended.
compartment door while the disc is
Total files and folders in the disc
being read.
should not exceed 512, it also
Do not load an unrecorded CD-R/RW
depends on the length of the file/
disc into the unit. It may take a longer
folder names.
time to read the disc.
For mixed mode discs, only one
Playback capability for CD-RW discs
mode will be selected for playback
may vary due to variations in the
depending on the recording format.
quality of the CD-RW disc and the
To ensure good performance, wait
recorder used to create the disc.
until the disc changer completely
reads the disc before proceeding.
mp3 files in CD ROM EXTRA format
disc cannot be recognized.
Program playback
Setting up a program list
Playing a program list
If you are not currently in the program mode,
1. While playback is stopped for an audio CD,
mp3/wma disc or USB device, press
/
press PROG/SET and then
to start the
program playback.
to select the tracks to be added to the
program list.
Displaying the program list
2. Press ADD to save the selected track into
the next available program location.
1. While playback is stopped, press PROG/SET
3. Repeat steps 1 to 2 to store more tracks
to enter the program mode.
into program memory.
2. Press
/
to view each track
assignment in the program list.
You can create a program of
Deleting from program list
up to 32 tracks.
1. While in the program mode, press
/
Only the first 99 tracks from
to select the track assignment to
each disc can be programmed.
delete.
2. Press DEL.
3. Press
/
to select "Y" to delete or
"N" to cancel the deletion.
4. Press DEL to confirm the selection.
Deleting the entire program
list
1. While in the program mode, press and hold
DEL.
2. Press
/
to select "Y" to delete or
"N" to cancel the deletion.
3. Press DEL to confirm the selection.
Warranty
Limited warranty (United
Installation and related adjustments.
States)
Signal reception problems not caused by
your unit.
What your warranty covers:
Damage from misuse or neglect.
Defects in materials or workmanship.
Cleaning of audio heads.
Batteries.
For how long after your purchase:
A unit that has been modified or
One year from date of purchase for labor
incorporated into other products or is used
and parts
for institutional or other commercial
Warranty period for rental units begins
purposes.
with the first rental or 45 days from date
A unit purchased or serviced outside the
of shipment to the rental firm, whichever
U.S.A.
comes first.
Acts of nature, such as but not limited to
lightning damage.
What we will do:
Pay any Authorized RCA Audio Service
Product Registration:
Center the labor charges to repair your
Please complete and mail the Product
unit.
Registration Card packed with your product.
Pay any Authorized RCA Audio Service
It will make it easier to contact you should
Center for the new or, at our option,
it ever be necessary. The return of the card
refurbished replacement parts required to
is not required for warranty coverage.
repair your unit.
Limitation of Warranty:
How you get service:
THE WARRANTY STATED ABOVE IS THE
Take your unit to any Authorized RCA
ONLY WARRANTY APPLICABLE TO THIS
Audio Service Center. To identify your
PRODUCT. ALL OTHER WARRANTIES,
nearest Authorized RCA Audio Service
EXPRESS OR IMPLIED (INCLUDING ALL
Center, ask your dealer, look in the Yellow
IMPLIED WARRANTIES OF
Pages, or call 1-800-336-1900.
MERCHANTABILITY OR FITNESS FOR A
Show the Authorized Service Center
PARTICULAR PURPOSE) ARE HEREBY
Representative your evidence of purchase
DISCLAIMED. NO VERBAL OR WRITTEN
date or first rental.
INFORMATION GIVEN BY THOMSON INC.,
Pick up your unit when repairs are
ITS AGENTS OR EMPLOYEES SHALL CREATE
completed.
A GUARANTY OR IN ANY WAY INCREASE
Proof of purchase in the form of a bill of
THE SCOPE OF THIS WARRANTY.
sale or receipted invoice which is evidence
REPAIR OR REPLACEMENT AS PROVIDED
that the product is within the warranty
UNDER THIS WARRANTY IS THE EXCLUSIVE
period must be presented to obtain
REMEDY OF THE CONSUMER. THOMSON
warranty service. For rental firms, proof of
INC. SHALL NOT BE LIABLE FOR INCIDENTAL
first rental is also required.
OR CONSEQUENTIAL DAMAGES RESULTING
FROM THE USE OF THIS PRODUCT OR
What your warranty does not cover:
ARISING OUT OF ANY BREACH OF ANY
Customer instruction. (Your Owner's
EXPRESS OR IMPLIED WARRANTY ON THIS
Manual describes how to install, adjust, and
PRODUCT. THIS DISCLAIMER OF
operate your unit. Any additional
WARRANTIES AND LIMITED WARRANTY ARE
information should be obtained from your
GOVERNED BY THE LAWS OF THE STATE OF
dealer.)
Important information
Important battery
Don't infringe
information
This product should only be used for the
Remove the batteries to avoid leakage if
purposes for which it is sold, that is,
you do not use your remote control for-
entertainment, violating no copyright law. Any
more than one month.
attempts to use this product for which it is not
intended is unlawful and therefore not
Discard leaky batteries immediately as
leaking batteries may cause skin burns or
condoned by Thomson.
other personal injuries. Dispose of batteries
in the proper manner, according to
Portions based upon Microsoft Windows Media
provincial and local regulations.
Technologies. Copyright © 1999 Microsoft
Any battery may leak electrolyte under the
Corporation. All Rights Reserved. Microsoft,
following circumstances:
Windows Media, and the Windows Logo are
trademarks or registered trademarks of
-
if mixed with a different battery type,
-
if inserted incorrectly,
Microsoft Corporation in the United States and/
-
if all batteries are not replaced at the
or other countries.
same time,
The descriptions and characteristics given in this
-
if disposed of in fire, or
-
if an attempt is made to charge a battery
document are given as a general indication and
not intended to be recharged.
not as a guarantee. In order to provide the
highest quality product possible, we reserve the
Headset safety
right to make any improvement or modification
without prior notice. The English version serves
Have a Blast-Just Not in your
as the final reference on all products and
eardrums!
operational details should any discrepancies
Make sure you turn down the
arise in other languages.
volume on the unit before you
put on headphones. Increase
the volume to the desired level only
after headphone are in place.
Do not play your headset at high volume.
Hearing experts warn against extended
high-volume play.
If you experience ringing in your ears,
reduce volume or discontinue use.
You should use with extreme caution or
temporarily discontinue use in potentially
hazardous situations.
Even if your headset is an open-air
designed to let you to hear outside sounds,
do not turn up the volume so high that
you are unable to hear what is around you.
General controls
PROG/SET
CLOCK – to enter the clock setting mode; to
to enter the program mode for CD, USB
show the clock time.
and tuner.
in USB mode, to enter the file rename
TIMER – to enter the timer setting mode; to turn
operation.
on or off the timer.
STOP
SLEEP – to select the time interval in minutes
in CD, USB or mp3/wma disc mode, to stop
before the unit turns off automatically.
the playback.
in USB or mp3/wma disc mode, to return to
FOLDER/PRESET
/
the first track of the current disc in stop
in USB or mp3/wma disc mode, to select the
mode; to display the total number of tracks
previous or next folder.
on the current disc when playback is
in tuner mode, to select the previous or
completely stopped.
next preset stations.
in recording mode, to stop recording to the
USB device.
CD REC – to start and stop recording to the USB
device.
BAND/REPEAT
in tuner mode, to change between the FM
and AM radio bands; to enter the auto
preset programming in FM mode when
pressed for 2 seconds.
in CD mode, to repeat a track, a CD or all
CDs.
in USB or mp3/wma disc mode, to select the
repeat one file or repeat all files mode.
FM ST/INTRO
to select between the stereo and mono
sound in the FM tuner mode.
to turn the intro mode on or off to play
the first 10 seconds of each track in CD, USB
or mp3/wma disc mode.
– to turn on or off random listening in CD,
USB or mp3/wma disc mode.
Disc and USB playback
Discs playback
USB playback
1. Press SOURCE repeatedly to select the CD
1. Insert the USB device's plug into the main
mode.
unit's USB jack.
2. Press
to open the disc compartment.
2. Press SOURCE repeatedly to select the USB
3. Insert up to 5 discs with the label facing up.
mode.
4. Press
again to close the disc
3. Press
when playback is stopped to
compartment.
begin playback. Press
during playback
The occupied disc tray icons light up on the
to pause the playback. Press again to
display and the current disc icon flashes.
resume the playback.
If the disc is a mp3/wma CD, the respective
4. Press
to stop the playback.
mp3 and wma icon lights on the display.
5. Unplug the device to disconnect.
5. Press
when the disc is stopped to
begin playback. Press
during playback
to pause the disc. Press again to resume the
playback.
6. During playback, press
to stop the
• Be sure to remove all discs from
playback.
the disc compartment before
moving or transporting the unit!
Play and load simultaneously
Do not push to force closing of the tray
during CD playback or tray opening.
1. Press
to open the disc tray while a CD is
Press DISC 1/ DISC 2 / DISC 3 / DISC 4
playing.
or DISC 5 to directly play the entire
2. Load/change discs for available trays.
single CD. To play all discs in the unit,
3. Press
again to close the tray.
press
in the CD mode.
Selecting discs
Press DISC 1 / DISC 2 / DISC 3 / DISC 4 or
DISC 5 on the main unit to select a disc.
Press DISC SKIP on the remote control to skip
discs.
Recording
Recording CD to USB device
Deleting a file from USB
device
1. Connect the USB device to the main unit.
2. When the CD is paused or stopped, press
1. In the USB mode, select the file to delete
CD REC to start the CD playback and
using
/
.
recording will begin automatically. This is
2. Press DEL on the remote control.
indicated by the REC icon on the display.
3. Press
/
on the main unit to select
3. Press CD REC or
to stop the recording.
"Y" to delete or "N" to cancel the deletion.
4. Press DEL to confirm the selection.
Example
To record only the selected tracks from a CD:
Deleting all files from USB
1. Create a CD program (Refer to "Setting Up
device
a Program List").
In the USB mode, press and hold DEL on the
2. From normal playback mode, press PROG.
remote control to delete all the files on the USB
3. Press CD REC, playback and recording will
device. Repeat steps 3-4 of the above to delete
begin automatically. This is indicated by the
all the files.
PROG and REC icon on the display.
4. Press CD REC or
to stop recording.
Renaming files
You can rename files in the USB device.
1. In the USB mode, press PROG/SET to enter
the rename mode.
• If CD playback is already
started or paused, recording will
2. Adjust VOLUME on the main unit or press
start instantly from the time point
VOL + / – to select alphabets.
3. Press NEXT on the main unit or
which is playing or paused when
CD REC is pressed.
FOLDER/PRESET
on the remote control
Recording stops automatically when the
to confirm the current alphabet and move
CD stops (e.g. end of disc is reached).
to the next alphabet.
The encoding bitrate for CD is 128 kbps.
Press DEL to delete the current alphabet.
Make sure "write protect" is turned off
Press PREV or FOLDER/PRESET
to edit
in the USB device during recording.
the previous alphabet.
4. Press PROG/SET to confirm and store the
new file name after editing the last
alphabet.
Warranty
INDIANA. EXCEPT TO THE EXTENT
PROHIBITED BY APPLICABLE LAW, ANY
IMPLIED WARRANTY OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE
ON THIS PRODUCT IS LIMITED TO THE
APPLICABLE WARRANTY PERIOD SET FORTH
ABOVE.
How State Law relates to warranty:
Some states do not allow the exclusion nor
limitation of incidental or consequential
damages, or limitations on how long an
implied warranty lasts, so the above
limitations or exclusions may not apply to
you.
This warranty gives you specific legal rights,
and you also may have other rights that
vary from state to state.
If you purchased your unit outside the
United States:
This warranty does not apply. Contact your
dealer for warranty information. Service
calls which do not involve defective
materials or workmanship are not covered
by this warranty. Costs of such service calls
are the sole responsibility of the purchaser.

Comments to this Manuals

Symbols: 0

Latest comments:

×

Select the desired size and copy embed code

Copy your embed code and put on your site: