Page of 4
Download Bookmark Comment

Pioneer DEH-P4300 Operation Manual

Pioneer deh-p4300: install guide.
Hide thumbs
   
Connecting the Units
<ENGLISH>
Note:
• This unit is for vehicles with a 12-volt battery and
• When an external power amp is being used with
Front output
negative grounding. Before installing it in a recre-
this system, be sure not to connect the blue/white
15 cm
Power amp
ational vehicle, truck or bus, check the battery
lead to the amp's power terminal. Likewise, do not
(sold separately)
voltage.
connect the blue/white lead to the power terminal
This Product
Connecting cords with RCA pin plugs
• To avoid shorts in the electrical system, be sure to
of the auto-antenna. Such connection could cause
(sold separately)
disconnect the ≠ battery cable before beginning
excessive current drain and malfunction.
Power amp
installation.
• To avoid short-circuiting, cover the disconnected
(sold separately)
Rear or Subwoofer output
• Refer to the owner's manual for details on con-
lead with insulating tape. Especially, insulate the
necting the power amp and other units, then make
unused speaker leads without fail. There is a possi-
connections correctly.
bility of short-circuiting if the leads are not insulat-
Blue/white
Fuse
DEH-P4300
• Secure the wiring with cable clamps or adhesive
ed.
To system control terminal of the power amp or
tape. To protect the wiring, wrap adhesive tape
• To prevent incorrect connection, the input side of
Auto-antenna relay control terminal (max. 300mA
Antenna jack
around them where they lie against metal parts.
the IP-BUS connector is blue, and the output side
12 V DC).
• Route and secure all wiring so it cannot touch any
is black. Connect the connectors of the same colors
System remote control
moving parts, such as the gear shift, handbrake and
correctly.
Multi-CD player
seat rails. Do not route wiring in places that get
• If this unit is installed in a vehicle that does not
DEH-P43
IP-BUS input (Blue)
(sold separately)
hot, such as near the heater outlet. If the insulation
have an ACC (accessory) position on the ignition
of the wiring melts or gets torn, there is a danger of
switch, the red lead of the unit should be connected
the wiring short-circuiting to the vehicle body.
to a terminal coupled with ignition switch ON/OFF
• Don't pass the yellow lead through a hole into the
operations. If this is not done, the vehicle battery
Front speaker
Front speaker
engine compartment to connect to the battery. This
may be drained when you are away from the vehi-
IP-BUS cable
will damage the lead insulation and cause a very
cle for several hours. (Fig. 1)
dangerous short.
• Do not shorten any leads. If you do, the protection
circuit may fail to work when it should.
• Never feed power to other equipment by cutting
Yellow
the insulation of the power supply lead of the unit
To terminal always supplied
White
Gray
and tapping into the lead. The current capacity of
with power regardless of
Front speaker
Front speaker
the lead will be exceeded, causing overheating.
ignition switch position.
• When replacing fuse, be sure to use only fuse of
White/black
Gray/black
the rating prescribed on this unit.
ACC position
No ACC position
• Since a unique BPTL circuit is employed, never
Red
Left
Right
wire so the speaker leads are directly grounded or
Fig. 1
To electric terminal controlled
the left and right ≠ speaker leads are common.
Green
Violet
by ignition switch (12 V DC)
• Speakers connected to this unit must be high-
ON/OFF.
Rear Speaker
Rear Speaker
power types with minimum rating of 50 W and
• The black lead is ground. Please ground this lead
or Subwoofer
or Subwoofer
separately from the ground of high-current prod-
impedance of 4 to 8 ohms. Connecting speakers
Green/black
Violet/black
ucts such as power amps.
with output and/or impedance values other than
This product conforms to CEMA cord colors.
If you ground the products together and the ground
those noted here may result in the speakers catch-
Orange/white
Le code de couleur des câbles utilisé pour ce produit est
ing fire, emitting smoke, or becoming damaged.
becomes detached, there is a risk of damage to the
To lighting switch terminal.
• When this product's source is switched ON, a con-
products or fire.
conforme à CEMA.
trol signal is output through the blue/white lead.
Rear Speaker
Rear Speaker
• Cords for this product and those for other prod-
Connect to an external power amp's system remote
Black (ground)
or Subwoofer
or Subwoofer
ucts may be different colors even if they have the
control or the car's Auto-antenna relay control ter-
With a 2 speaker system, do not connect
To vehicle (metal) body.
same function. When connecting this product to
minal (max. 300 mA 12 V DC). If the car features
anything to the speaker leads that are not
another product, refer to the supplied Installation
a glass antenna, connect to the antenna booster
connected to speakers.
manuals of both products and connect cords that
power supply terminal.
have the same function.
Note:
When a subwoofer is connected to this unit instead of a rear speaker,
change the rear output setting in the Initial Setting. (Refer to the
Perform these connections when using a
Operation Manual.) The subwoofer output of this unit is monaural.
different amp (sold separately).
Fig. 2
Printed in
Thailand
Imprimé
en Thaïlande
<CRD3311-A/JS> UC
<KMMUU/00I00000>

   Also See for Pioneer DEH-P4300

   Related Manuals for Pioneer DEH-P4300

   Summary of Contents for Pioneer DEH-P4300

  • Page 1

    • Refer to the owner’s manual for details on con- necting the power amp and other units, then make connections correctly. DEH-P4300 • Secure the wiring with cable clamps or adhesive tape. To protect the wiring, wrap adhesive tape around them where they lie against metal parts.

  • Page 2

    Installation Note: Removing the Unit (Fig. 5) (Fig. 6) • Before finally installing the unit, connect the • If installation angle exceeds 60° from horizontal, wiring temporarily, making sure it is all connected the unit might not give its optimum performance. up properly, and the unit and the system work (Fig.

  • Page 3

    Raccordements des appareils Remarque: • Cet appareil est destiné aux véhicules avec une bat- • Quand la source de ce produit est positionnée sur terie de 12 V, avec pôle négatif à la masse. Avant de ON, un signal de commande est sorti par le fil l’installer dans un véhicule de loisir, un camion ou bleu/blanc.

  • Page 4

    Installation Remarque: Dépose de l’unite (Fig. 5) (Fig. 6) • Avant de finaliser l’installation de l’appareil, con- • L’angle de l’installation, ne doit pas dépasser 60° necter temporairement le câblage en s’assurant que par rapport à l’horizontale, faute de quoi l’unité ne tout est correctement connecté...

This manual also for:

Deh-p43

Comments to this Manuals

Symbols: 0
Latest comments: