Wiring - Aiphone JF-2MED Installation & Operation Manual

3

WIRING

Insert wires securely into each terminal as shown.
DOOR 1
Video door station
AIPH ONE
JF-D A
JF-DA
AIPHON
E
JF-DVF
AIPHO
NE
JF-DV
JF-DV JF-DVF
A1 A2
DOOR 2
AIPH ONE
JF-D A
JF-DA
AIPHON E
JF-DVF
AIPHO
NE
JF-DV
JF-DV JF-DVF JF-D
(Audio only)
Setting is required. (Refer to section 7-7)
A1 A2
Optional call extension speaker IER-2
OP
Door release
Door release EL-9S (AC 12 V, 0.35 A) or
equivalent, requires a separate AC transformer.
Run separate cables for audio/video and door
release.
Door release contact: AC/DC 24 V, 0.5 A
(N/O dry closure contact L, L).
Optional selective door release
adaptor RY-3DL
Use RY-3DL when connecting
door release to 2 locations.
AC Transformer
PT
JF-2MED
2
NP
Power supply +, - (DC 18 V)
PS-1810DIN
230V AC
2
NP
IN 230V~ 50/60Hz
NL
1A - +
-
+
18V DC 1 A
2
NP
OP
EL-9S
RY-3DL JF-2MED
EL-9S
Option connector
L1
C1
b1
L1
EL-9S b2
b3
L2
L
C2
D1
L2 Release connector
E
PT
D2
DC 18V
+
–
Master monitor station
#2 #1
P
Release connector
2
- +
DC 18 V
Option connector
PS-1820
N
L
18V DC
100V - 240V -
2 A
50/60 Hz
Control external devices connected with release connector
and option connector.
[1] Door release output
(AC/DC 24 V, 0.5 A N/O dry closure contact)
Connect the brown and red wires from the release
connector to the door release (or to the RY-3DL as shown
in the wiring diagram).
[2] Options output
(AC/DC 24 V, 1.6 A N/O dry closure contact)
[3] Video signal output
(NTSC, 1 Vp-p/75 Ω) Wiring distance: 3 m
2 [4] Door release-linked entrance output
[5] Press-to-talk setting input
[1]
NP
If the blue and white wires are shorted, press-to-talk will
PT
not be operable.
[6] Foot switch input
Connect a commercially-available foot switch to the
purple and white wires (N/O dry closure contact).
[7] External sensor input
OG: Orange
OG(b1) Setting is required. (Refer to section 7-9)
YE: Yellow
YE(b2)
GR: Green
GR(E)
BR: Brown
Input method
RD: Red
BR(L)
Detection confirmation time 100 mS or more
RD(L)
Contact resistance
+
Terminal short current
PS18
–
Voltage between terminals
- 4 -
(BR) L
[1]
(RD) L
#1
(OG) SW
[2]
(YE) SW
(BR) V +
[3]
(RD) V -
(OG) b1
[4]
(YE) b2
#2
(GR) E
(BL) PK
(PR) FS
(GY) KS
[7]
(WH) E
To prevent shorts, be sure to cut unused lead wires
at the bottom and insulate the ends.
Setting is required. (Refer to section 7-8)
N/O dry closure contact
External sensor input
(start signal only detection method)
During dry closure: Less than 700 Ω
Less than 10 mA
Less than DC 20 V
(when open between terminals)
Door release
or
RY-3DL
RY-3DL
[5]
[6]