Ipr 1600 Specification Sheet - Peavey IPR 1600 Operating Manual

Rated Power (2 x 2 ohms)
Rated Power (2 x 4 ohms)
Rated Power (2 x 8 ohms)
Rated Power (1 x 2 ohms)
Rated Power (1 x 4 ohms)
Rated Power (1 x 8 ohms)
Minimum Load Impedance
Maximum RMS Voltage Swing
Frequency Response
T.H.D. (2 x 2 ohms)
T.H.D. (2 x 4 ohms)
T.H.D. (2 x 8 ohms)
Input CMRR
Voltage Gain
Crossover
Crosstalk
Hum and Noise
Damping Factor (8 ohms)
Phase Response
Slew Rate:
Input Sensitivity
Input Impedance
Current Draw @ 1/8 power
Current Draw @ 1/3 power
Cooling
Controls
Indicator LEDs
Protection
Connectors
Construction
Dimensions
Dimensions Packed
Net Weight*
Gross Weight
Warranty
Rated power readings made with BW: <10 Hz to 22 kHz. All power measurements made at 120 VAC and 240VAC.
2 ohm power is time limited by circuit breaker.
*Net Weight does not include power cord.
™
IPR 1600 Specification Sheet
- 800 watts per channel @ 1 kHz at <0.1% T.H.D. both channels driven.
- 530 watts per channel @ 1 kHz at <0.1% T.H.D. both channels driven.
- 300 watts per channel @ 1 kHz at <0.1% T.H.D. both channels driven.
- 1000 watts @ 1 kHz at <0.1% T.H.D.
- 600 watts @ 1 kHz at <0.1% T.H.D.
- 320 watts @ 1 kHz at <0.1% T.H.D.
- 2 ohms
- 55 volts
- 10 Hz - 50 kHz; +0, -3 dB at 1 watt
- <0.1% @ 600 watts per channel from 20 Hz to 1.5 kHz, decreasing to 500 watts at 20 kHz at <0.25%
- <0.1% @ 470 watts per channel from 20 Hz to 20 kHz
- <0.1% @ 250 watts per channel from 20 Hz to 20 kHz
- > - 60 dB @ 1 kHz
- x 60 (+35 dB)
- 100 Hz switchable 2nd order High pass and 3rd order Low Pass per channel
- > -70 dB @ 1 kHz at 100 watts power @ 4 ohms
- > -105 dB, "A" weighted referenced to rated power @ 4 ohms
- > 170:1 @ 20 Hz - 1 kHz at 8 ohms
- +9 to - 86 degrees from 20 Hz to 20kHz
- > 12V/us
- .775 volts +/- 3% for 1 kHz 4 ohm rated power, .68 volts +/- 3% for 1 kHz. 2 ohm rated power
- 15k ohms, balanced and 7.5k ohms unbalanced.
- 550 watts @ 2 ohms, 390 watts @ 4 ohms, 250 watts @ 8 ohms
-1,160 watts @ 2 ohms, 810 watts @ 4 ohms, 460 watts @ 8 ohms
- Temperature dependent variable speed 80 mm DC fan
- 2 front panel attenuators, crossover select switch for H.P.F, Normal and L.P.F.
- 2 DDT (clip limiting), 2 Signal presence, 2 Active status, 2 Temp and 2 DC protect
- Thermal, DC, subsonic, incorrect loads, under and over voltage
- Inputs: Dual Combi 1/4" XLR, Outputs: Dual 1/4" signal patch, dual Speakon connectors
- 0.062" thick aluminum
- 3.5"x19" x 10.5" behind front panel + 0.6" for handle
- 4.72" x20.8" x 12.44" (120mm x 530mm x 316mm)
- 3.23 kg (7.125 lbs.)
- 4.31 kg (9.5 lbs.)
- 5 years
22