Panasonic WV-CP254H Operating Instructions

Color CCTV Cameras
W V
- C P 2
5 4 H
Operating Instructions
WV-CP254H
Model No.
(Lens: Option)
Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.
N0703-1103 3TR001812BAA
NOTE: This equipment has been tested and found
to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules.
CAUTION These limits are designed to provide reasonable
protection against harmful interference when the
RISK OF ELECTRIC
equipment is operated in a commercial environ-
SHOCK DO NOT OPEN
ment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed
and used in accordance with the instruction manu-
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, al, may cause harmful interference to radio com-
munications.
DO NOT REMOVE COVER (OR BACK).
Operation of this equipment in a residential area is
NO USER-SERVICEABLE PARTS INSIDE. REFER SER-
likely to cause harmful interference in which case
VICING TO QUALIFIED SERVICE PERSONNEL.
the user will be required to correct the interference
at his own expense.
FCC Caution: To assure continued compliance,
The lightning flash with arrowhead
(example - use only shielded interface cables when
symbol, within an equilateral trian-
connecting to computer or peripheral devices). Any
gle, is intended to alert the user to
changes or modifications not expressly approved
the presence of uninsulated "dan-
by the party responsible for compliance could void
gerous voltage" within the product's
the user's authority to operate this equipment.
enclosure that may be of sufficient
magnitude to constitute a risk of
SA 1965
electric shock to persons.
The serial number of this product may be found on
the top of the unit.
You should note the serial number of this unit in the
The exclamation point within an
space provided and retain this instruction as a per-
equilateral triangle is intended to
manent record of your purchase to aid identification
alert the user to the presence of
important operating and mainte- in the event of theft.
nance (servicing) instructions in the
Model No. WV-CP254H
literature accompanying the appli-
ance.
SA 1966 Serial No.
WARNING: To prevent fire or electric shock hazard, do not expose this appliance to rain or moisture.
The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such
as vases, shall be placed on the apparatus.
PREFACE
Panasonic's WV-CP254H digital signal processing and digital signal processing LSI's. This model
color CCD camera introduces a new level of high offers cutting-edge technology for advanced video
picture quality and high resolution through the use surveillance.
of a 1/3-inch interline transfer CCD image sensor
having 752 horizontal pixels (picture elements),
FEATURES
1. The following functions are built in. 3. Signal-to-noise ratio of 50 dB (min)
(1) Auto Light Control (ALC)/Electronic Light (at AGC OFF, weight ON)
Control (ELC)
(2) Automatic Gain Control (AGC) and 4. Horizontal resolution of 480 lines
Automatic Tracing White Balance (ATW)
(3) Camera synchronization mode selectable 5. Auto iris lens control selectable between
between internal (INT), Line-locked (LL) video signal and DC power supply.
and Multiplexed Vertical Drive (VD2).
6. Auto black-and-white mode enables the cam-
2. Minimum Illumination of 1.0 lx (0.1 foot-can- era to switch between color and black and
dle) at color mode, 0.15 lx (0.015 foot-candle) white picture in response to light input.
at black and white mode with F1.4 lens.
PRECAUTIONS
1. Do not attempt to disassemble the camera. 3. Do not expose the camera to rain or
To prevent electric shock, do not remove moisture, or try to operate it in wet areas.
screws or covers. Turn the power off immediately and ask a
There are no user serviceable parts inside. qualified service person
Ask a qualified service person for servicing. Moisture can damage the camera and also
create the danger of electric shock.
2. Handle the camera with care.
Do not abuse the camera. Avoid striking, 4. Do not use strong or abrasive detergents
shaking, etc. The camera could be damaged when cleaning the camera body.
by improper handling or storage. Use a dry cloth to clean the camera when
dirty.
In case the dirt is hard to remove, use a mild
detergent and wipe gently. Afterwards, wipe
off the remained part of the detergent in it with
a dry cloth.
5. Clean the CCD faceplate with care. 7. Do not operate the camera beyond the
Do not clean the CCD with strong or abrasive specified temperature, humidity or power
detergents. Use lens tissue or a cotton tipped source ratings.
applicator and ethanol. Use the camera under conditions where tem-
perature is between –10 °C - +50 °C (14 °F -
6. Never face the camera towards the sun. 122 °F), and humidity is below 90 %. The input
Do not aim the camera at bright objects. power source is AC 24 V.
Whether the camera is in use or not, never 8. Do not connect this camera during a
aim it at the sun or other extremely bright lightning storm.
objects. Otherwise, blooming or smear may Otherwise, electric shock may be caused.
be caused.
Caution:
To prevent fire or electric shock hazard,
use a UL listed cable (VW-1, style 1007) for
the AC 24 V Input Cable.
MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS
!7
Printed in Japan !8
For U.S.A
BLC SHARP COLOR
ON AGC VIDEO FIX HI
INT HI ALC ATW1 1MI N
Pull and remove the cap
LL LOW ELC ATW2 5SEC
OFF SOFT DC AUTO LOW
DAY/NIGHT
Day / GND
Night IN
POWER
!6 !5
y i !0 !2 !4
t u o !1 !3
BLC SHARP COLOR
ON VIDEO FIX HI
AGC
INT HI ALC ATW1 1MI N
LL LOW ELC ATW2 5SEC
OFF SOFT DC AUTO LOW
DAY/NIGHT
q Auto Iris Lens Connector i Detail/Aperture Level Selector (SHARP,
Supplies power and control signals to an auto SOFT)
iris lens (not supplied). The detail/aperture level can be selected with
this selector. Set it to the desired position
w Focus Lock Knob
while observing the picture on the monitor.
This knob adjusts the back-focal distance or SHARP: Normal position.
picture focus. SOFT: Select this position when a Quad
e Lens (option)
o Automatic Light Control/Electronic Light
r Mount Adapter
Control Selector (ALC, ELC)
The camera mounting screw hole is for mount- Lets you select the mode according to the
ing the camera onto a mounting bracket. The lens type used.
camera is originally designed to be mounted ALC: Select this mode when an auto iris lens
from the bottom, however, a top-mounting
type is also available. To mount from the top, ELC: Select this mode when a fixed iris lens
remove the mount adapter from the bottom of
the camera by removing two fixing screws.
Attach the mount adapter to the top as shown
!0 Lens Drive Signal Selector (VIDEO, DC)
in the diagram, then mount the camera on the
mounting bracket. Make sure that two original Lets you select the mode according to the
screws are used when mounting the mount type of auto iris lens drive signal to be sup-
adapter; longer type screws may damage plied to the lens from the auto iris lens con-
inner components, too shorter type screws nector.
may cause the camera drop. VIDEO: Select this mode if you are using a
t Synchronization Mode Selector (INT, LL)
Selects the camera synchronization mode as DC: Select this mode if you are using a auto
either internal sync mode (INT) or line-lock
mode (LL).
!1 Auto-Tracing White Balance mode (ATW)
INT: Sets to internal 2:1 interlace.
Selector
LL: Sets to Line-lock mode.
The ATW mode can be selected with this
selector.
y Back Light Compensation Mode Selector
ATW1: Normal picture
(BLC ON, OFF)
ATW2: ATW in sodium lamp mode
Lets you select the mode according to the
position of the object and light conditions on
!2 Day/Night Mode Selector
the screen.
This function switches the condition of pic-
ON: Select this mode when a strong light tures from color to black and white in low light
such as a spotlight is in the background. conditions.
for servicing.
COLOR FIX: Color picture reverts to black-
OFF: Normal picture
The factory default setting is ON.
u AGC Level Selector
AGC level can be selected with this selector.
AGC automatically controls the gain of Image
brightness level.
HI: This setting raises more the gain and
brightness of images under low light con-
ditions.
LOW: Normal position
AUTO: The camera selects black-and-white
mode if the picture is dark, or color mode
if the picture is bright enough.
Notes:
• When using this unit with a video servo
control lens, you may not switch from the
black-and-white mode to the color mode
depending on lens iris.
In such a case, operate the lens adjuster
to open the aperture.
• This function may not be activated auto-
matically when a backlight or a strong
light source causes excessive contrast in
the picture. In such cases, use the
Day/Night input terminals.
!3 Duration Time Selector
This selector is available when the Day/night
switch position is 'AUTO'.
Switching time (5 sec. or 1 minute ) is selec-
table.
!4 BW Level Selector
Selects the luminance level.
This selector is available when the Day/night
switch position is 'AUTO'.
According to the luminance level, this camera
automatically switches the condition of picture
from color to black-and-white, or in reverse.
HI: Color picture switches to black-and-white
pictures at approx. 7 lx with F1.2 lens.
CONNECTIONS
■ Connections
q w e
Caution:
The following connections should be made by qualified service personnel or system installers in
accordance with NEC 725-51.
CP254H
WV-
Note: For the WV-CP254H Color CCTV Camera, do not use a transformer larger than 10VA.
r
Power Cable
BNC Plug
Mount adapter Video Output Cable
WV - CP 25 CP 25
4H 4H
WV C P 25 - C P 25
4H 4H
• Power supply connection
Recommended wire gauge sizes for 24 V AC line.
System is connected to this camera.
Copper wire #24 #22 #20
size (AWG) (0.22mm ) (0.33mm ) (0.52mm
2 2
(m) 20 30 45
Length
of cable
(Approx.)
(ft) 65 100 160
Cautions:
(ALC lens) is used with this camera.
1. Shrinking the cable-entry seal is a one-time
procedure. Do not shrink the cable-entry
or manual iris lens is used with this cam-
seal until it has been ascertained that the
era.
unit is functioning.
2. CONNECT THIS TO 24 V AC CLASS 2
POWER SUPPLY ONLY. Be sure to connect
the grounding lead to the GND terminal.
3. To prevent fire or electric shock hazard,
use a UL listed cable (VW-1, style 1007) for
the Input Terminal.
4. The connections should comply
auto iris lens that requires a video drive
National electrical Code (NEC).
signal.
iris lens that requires a DC drive signal.
Video Cable
1. It is recommended to use a monitor whose
resolution is at least equal to that of the
camera.
2. The maximum extensible coaxial cable
length between the camera and the monitor
is shown below.
Type of RG-59/U RG-6/U RG-11/U RG-15/U
coaxial cable (3C-2V) (5C-2V) (7C-2V)
Recommended (m) 250 500 600
and-white picture when an external
maximum
day/night switching signal is received cable length (ft) 825 1 650 1 980
(refer to Day/Night connections).
Note: When using this unit with infrared
rays or lighting of which color tem-
Installation of Auto Iris Lens
perature is 3 000 K or less, select
this mode without fail, and short-cir- Connector
cuit the Day/Night input terminals if
Install the lens connector (YFE4191J100) when
you select the black-and-white pic-
using a video drive ALC lens.
ture.
The installation should be made by qualified
(The AUTO mode may cause hunt-
service personnel or system installers.
ing.)
LOW: Color picture switches to black-and- Caution for Mounting the Lens
white pictures at approx. 5 lx with F1.2
lens. The lens mount should be a C-mount or CS-mount
The factory default setting is HI. (1"-32UN) and the lens weight should be less than
450 g (0.99 lbs). If the lens is heavier, both the lens
!5 Power Indicator (POWER)
and camera should be secured by using the sup-
porter.
!6 Day/Night Input Terminal
The protrusion at the rear of the lens should be as
(DAY/NIGHT IN/GND)
shown below.
This terminal is used for connecting the cam-
era to an external day/night detecting sensor.
Terminals opened: color picture
Terminals shortened: black-and-white picture
!7 Video Output Cable with BNC Connector
Connects the VIDEO IN connector of the mon-
itor.
!8 Power Cable
Cautions:
1. CONNECT THIS TO 24 V AC CLASS 2
POWER SUPPLY ONLY. Be sure to connect
FOCUS OR FLANGE-BACK ADJUSTMENT
the grounding lead to the GND terminal.
2. To prevent fire or electric shock hazard,
use a UL listed cable (VW-1, style 1007) for
1. Loosen the focus lock knob.
the Input Terminal.
3. The connections should comply with
2. Adjust the focus lock knob to obtain a focused
National Electrical Code (NEC).
point while watching the monitor screen.
3. Tighten the focus lock knob.
Caution: Tightening the knob by force will
cause damage to the knob or deviation
of focus.
Note: The object may be out of focus when
using a source of near-infrared light than
using the visible light.
Black (Live)
24 V AC, 60 Hz
White (Neutral)
(19.5 V-28 V)
(CLASS 2 SUPPLY ONLY) SPECIFICATIONS
Green/Yellow (Ground)
BNC Plug Pick-up device:
Scanning area:
Synchronization:
Scanning system:
Scanning:
To Video IN
Horizontal:
(CAMERA IN)
Vertical:
Horizontal resolution:
Video output:
BNC Plug
Signal-to-noise ratio:
Electronic light control:
Minimum illumination:
Aperture:
Lens mount:
Ambient operating temperature:
Cut the iris control cable at the edge of the lens
Ambient operating humidity:
connector to remove the existing lens connector
Power source and
and then remove the outer cable cover of the sup-
plied connector as shown in the diagram. power consumption:
#18
) (0.83mm )
2 2 The pin assignment of the lens connector is as fol-
Dimensions (without lens):
lows:
75
Pin 1: Power source; +9 V DC, 50 mA max.
Weights (without lens):
260 Pin 2: Not used
Day/Night
Pin 3: Video signal; 0.7 V[p-p]/40 kΩ
Pin 4: Shield, ground
Weights and dimensions indicated are approximate.
Specifications are subject to change without notice.
Rib
Pin 3
Pin 1
Pin 4
Pin 2 STANDARD ACCESSORIES
Solder the lens cable to the pins of the sup-
Operating Instructions (this document) ............................................. 1 pc.
plied connector.
The following parts are for installation:
with Body cap ........................................................................................... 1 pc.
ALC lens connector (YFE4191J100) .................................................. 1 pc.
Mounting the Lens
C-mount Adapter ............................................................................... 1 pc.
Caution:
Before you mount the lens, loosen the focus
lock knob, and rotate it clockwise until it
OPTIONAL ACCESSORIES
stops. If the ring is not at the end, the inner
lens or CCD image sensor may be damaged.
Lenses:
q Mount the lens by turning it clockwise on the
lens mount of the camera.
Note: When mounting the C-mount lens on
the camera, mount the C-mount adapter
by rotating it clockwise in advance.
w Connect the lens cable to the auto iris lens
(10C-2V)
connector on the side of the camera.
800
Lens mount
2 640
C-mount adapter
Panasonic Digital Communications & Security Company
WV CP 25 - CP 25
4H 4H
Unit of Matsushita Electric Corporation of America
w
Security Systems Group
www.panasonic.com/cctv
Executive Office: One Panasonic Way 3E-7, Secaucus, New Jersey 07094
Zone Office
Focus lock
Eastern: One Panasonic Way, Secaucus, NJ 07094 (201) 348-7303
knob
Central: 1707 N.Randal Road, Elgin, IL 60123 (847) 468-5205
Western: 6550 Katella Ave., Cypress, CA 90630 (714) 373-7840
2003 © Matsushita Electric Industrial Co., Ltd. All rights reserved.
Day/Night Connections
Connect an optical sensor to the Day/Night Input
terminals.
• Day/Night Input terminals with a capacity of
5 V DC pull-up input, 0.2 mA or more.
OFF: break contacts: color picture
ON: make contacts: black-and-white picture
Note: To activate the Day/Night function, set
Day/Night Mode Selector to COLOR FIX.
C-mount: Less than 13 mm (1/2")
CS-mount: Less than 8 mm (5/16")
WV - C P2 C P2
54 H 54 H
Loosen
Tighten
Focus lock
knob
752 (H) x 582 (V) pixels, interline transfer CCD
5.59 (H) x 4.68 (V) mm (equivalent to scanning area of 1/3 in.
pick-up tube)
internal, line-locked or multiplexed vertical drive (VD2),
selectable
2 : 1 interlace
525 lines / 60 fields / 30 frames
15.734 kHz
59.94 Hz
480 lines
1.0 V [P-P] NTSC composite 75 Ω / BNC connector
50 dB (min) (at AGC Off, weight On)
equivalent to continuous variable shutter speed between 1/50 s
and 1/15 000 s
1.0 lx (0.1 foot-candle) at color mode, 0.15 lx (0.015 foot-candle) at
black and white mode with F1.4 lens
SHARP or SOFT, selectable
CS-mount
−10 °C - +50 °C (14 °F - 122 °F)
less than 90 %
24 V AC 60Hz, 3.3 W
67 mm (W) x 65 mm (H) x 72.5 mm (D)
2-5/8" (W) x 2-9/16" (H) x 2-7/8" (D)
0.33 kg (0.7 lbs)
selectable COLOR FIX (→ external terminal active) or AUTO
WV-LA2R8C3B, WV-LA4R5C3B, WV-LA9C3B, WV-LA210C3, WV-LA408C3,
WV-LA908C3, WV-LZ61/10, WV-LZ62/2, WV-LZ62/8, WV-LF4R5C3A, WV-LF9C3A,
WV-LZ61/15, WV-LZA61/2, WV-LZF61/2
PANASONIC CANADA INC.
5770 Ambler Drive, Mississauga,
Ontario, L4W 2T3 Canada (905)624-5010
PANASONIC SALES COMPANY
DIVISION OF MATSUSHITA ELECTRIC OF PUERTO RICO INC.
San Gabriel Industrial Park 65th Infantry Ave. KM. 9.5 Carolina,
P.R. 00985 (809)750-4300