For assistance, please call: 1 - 888 - View - PTV (843 - 9788) or send e - mail to: consumerproducts@panasonic.com or visit us at www.panasonic.com For assistance, please call: 787 - 750 - 4300 or visit us at http://panasonic.net Before operating this product, please read these instructions carefully and save this manual for future use.
We hope it will help you to get the most out of your new product, and that you will be pleased with your Panasonic LCD projector.The serial number of your product may be found on its bottom. You should note it in the space provided below and retain this booklet in case service is required.
Page 3
Panasonic North America Address: One Panasonic Way 4B - 9 Secaucus, New Jersey 07094 Telephone number: 1 - 888 - View - PTV (843 - 9788) This device complies with Part 15 of the FCC Rules, Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Projection method ... 15 Front leg adjuster and throwing angle... 15 Lens shift and positioning... 16 Connections ... 18 Before connection to the projector ... 18 Connecting with AV devices... 18 Connecting with HDMI/PC ... 18 Basic Operation Switching the projector on/off ... 19 Power cord ...
Page 5
TEMP and LAMP Indicators ... 36 Controlling alerts ... 36 Care and Replacement ... 37 Before cleaning ... 37 Cleaning your projector ... 37 Before replacing the Lamp unit ... 38 When to replace the Lamp unit ... 38 Replacing the lamp unit... 39 Troubleshooting...
Do not place the projector on top of surfaces which are unstable. If the projector is placed on top of a surface which is sloped or unstable, it may fall down or tip over, and injury or damage could result.
Page 7
Strong light is emitted from the projector’s lens. If you place directly into this light, it can hurt or damage your skin. Do not look into the lens while the projector is being used. Strong light is emitted from the projector’s lens. If you look directly into this light, it can hurt and damage your eyes.
It is a good idea to clean the inside of the projector before the season for humid weather arrives. Ask your nearest Authorized Service Center to clean the projector when required.
Do not subject the projector to excessive vibration or shocks. The projector lens need to be handled with care. Cover the lens with the lens cover when transporting the projector. Cautions when installing Avoid setting up in places which are subject to vibration or shocks.
Do not project the same image for long periods of time, as this may remain as an afterimage on the liquid crystal panel. The liquid crystal panel of the projector is built with very high precision technology to provide fine picture details. Occasionally, a few stuck pixels may appear on the screen as fixed points of blue, green or red.
About Your Projector Remote control Front, back and top view POWER Turn the POWER on/off. (page 19) PICTURE MODE THEATER ROOM Switch to the best setting for a darker room. LIVING ROOM Switch to the best setting for a bright room.
Do not cover the ventilation openings or place anything within 10 cm (4") of them as this may cause damage or injury. While the projector is not in use, attach the Lens cover to protect the lens. 12 - E...
Page 13
Do not cover the ventilation openings or place anything within 10 cm (4") of the vents as this may cause damage or injury. This projector should only be used with the attached Power cord to ensure optimum performance and avoid damage to the projector.
* The results above are approximate and may differ slightly from the actual measurements. NOTE: Do not use the projector at a raised or a horizontally tilted position as it may cause malfunction of the projector. Make sure the projector lens surface is parallel with the screen. You can tilt the projector body approximately ±...
Projection method You can use the projector with any of the following 4 projection methods. To set the desired method in the projector, see “INSTALLATION” on page 35. Setting on a desk/floor and projecting from front INSTALLATION: FRONT/DESK Mounting in the ceiling and...
Setting up Lens shift and positioning If the projector is not positioned right in front of the center of the screen, you can adjust the projected image position by moving the Shift lever within the shift range of the lens.
Page 17
NOTE: When the projector is located right in front of the screen and the Shift lever is centerd, you will get the best quality of the projection image. When the Shift lever is at the vertical limit of the shift range, you cannot move the lever to the horizontal limit, likewise when the Shift lever is at the horizontal limit of the shift range, you cannot move the lever to the horizontal limit.
Connections Before connection to the projector Read and follow the operating and connecting instructions of each peripheral device. The peripheral devices must be turned off. Use cables that match each peripheral device to be connected. Confirm the type of video signals. See “List of compatible signals” on page 41.
ORANGE Flashing NOTE: While the projector is cooling the lamp, do not switch the MAIN POWER off or unplug the Power cord. Disconnecting 1. Make sure the MAIN POWER is switched off and unplug the Power cord from the wall socket.
See page 34 about switching on/off the STARTUP LOGO. Some small rattling or tinkling sound may be heard when starting up, but this is normal and does not affect the performance of the projector. Switching off the projector 1. Press the POWER button.
2. Adjust the projected image with the Shift lever. See "Lens shift and positioning" on page 16. Unlock 3. Adjust the angle of the projector. Screw down the Front leg adjuster and adjust the angle vertically. NOTE: Do not touch the Air exhaust port as this may cause burns or injury.
Remote control operation Operating range You can operate the projector with the Remote control within the remote range 7 m. Facing to the projector Ensure the Remote control emitter is facing to the Remote control signal receptor on front of the projector and press the required buttons to operate.
Remote control operation Adjusting the image You can display one of the PICTURE or ADVANCED menu items by pressing the PICTURE ADJUSTMENT button. Press the button to switch between PICTURE and ADVANCED menu. Press F G to select the required menu item and I H to adjust.
Page 25
Adjust the vividness of the color. COLOR Setting range: -30 to +30 Default: 0 Adjust the color tone. TINT Setting range: -30 to +30 Default: 0 Adjust the brightness of the color. BRIGHTNES Setting range: -20 to +20 Default: 0 4.
Menu Navigation The menu system allows you to access functions which do not have their own dedicated buttons on the Remote control. The menu options are structured and categorized. You can navigate through the menu with F G I H buttons. Navigating through the MENU Displaying the Main menu...
Sub-menu Sub-menu items vary by the selected input signal. PICTURE menu See “PICTURE Menu” on page 28. Sub-menu items PICTURE MODE CONTRAST BRIGHTNESS COLOR TINT SHARPNESS COLOR TEMPERATURE DYNAMIC IRIS LIGHT HARMONIZER ADVANCED MENU FAVOURITE SAVE FAVOURITE LOAD SIGNAL MODE 1.
PICTURE Menu See “Navigating through the MENU” on page 26. PICTURE MODE Depending on the projection environment, you can use these preset parameter settings to optimise image projection. Press I H to cycle through the options. For a bright room Setting for a general image, such as NORMAL sports or games...
TINT You can adjust the skin tone in the projected image. More More greenish reddish Setting range: -32 to +32 When PC is connected, this function is available with 1 125 (1 080)/60i, 1 125 (1 080)/50i, 1 125 (1 080)/60p and 1 125 (1 080)/50p signals only.
PICTURE Menu NR (Noise Reduction) You can switch the automatic noise reduction system on/off. Press I H to select the required setting. • ON: Automatic noise reduction • OFF: No noise reduction NOTE: Applying noise reduction may affect image quality. MPEG NR You can switch the automatic noise reduction system for MPEG format images on/off.
POSITION Menu See “Navigating through the MENU” on page 26. H - POSITION You can move the projected image horizontally for fine adjustment. Move Move left right V - POSITION You can move the projected image vertically for fine adjustment. Move Move down...
POSITION Menu ASPECT You can switch the aspect ratio manually when needed. Aspect ratio options and projection example If you apply the aspect ratio options to the projected image, the result will be as follows. The result may differ due to the input signals. See “Switching the aspect ratio” on page 23. VIDEO/S-VIDEO/COMPONENT Not available with 1 125 (1 080)/50i, 1 125 (1 080)/60i, 1 125 (1 080)/50p, 1 125 (1 080)/60p, 1 125 (1 080)/24p, 750 (720)/50p and 750 (720)/60p signals.
Setting range: 0 to +10 OVER SCAN is not available with PC signals. POSITION Menu KEYSTONE If the projector is aligned non-perpendicularly to the screen, or if the projection screen has an angled surface, you can vertically correct keystone. Image...
LEFT BACK COLOR You can choose a BLUE or BLACK screen for when the projector is idle. Press I H to select an option. STARTUP LOGO You can switch on/off the logo that is displayed when starting up. Press I H to select an option.
Press I H to cycle through the options. See “Switching off the projector automatically” on page 23. ALTITUDE If you use the projector at high elevations, set the fan speed to HIGH. Press I H to select HIGH or LOW. NOTE: At 1 400 m (4593 ft) above sea level, the setting must be HIGH.
TEMP and LAMP Indicators Controlling alerts If a problem should occur with the projector, the TEMP and/or LAMP indicators will alert you. Respond to the alert as follows. 1. Confirm the POWER indicator status and turn off the projector in the proper way.
Cleaning the Air filter If the Air filter is excessively dirty, the internal temperature of the projector increases and may cause malfunction. Clean the Air filter regularly every 100 hours of usage. 1. Turn the projector upside down and place it gently on a soft cloth.
The Lamp unit is consumable and the brightness decreases by duration of usage. The LAMP indicator will alert you of the replacement timing at 1 800 hours, and at 2 000 hours, the projector will be turned off. 1 800 or 2 000 hours is a rough guidance and might be shortened by the usage conditions, characteristics of the lamp unit, environmental conditions, and so on.
If the lamp usage time has passed 2 000 hours (when LAMP POWER has been set to NORMAL), the projector will switch to standby mode after approximately 10 minutes of operation. The resetting procedure should thus be completed within 10 minutes.
The SHUTTER function may be in use. The lens cover may still be attached to the lens. The lens focus may not have been set correctly. The projector may not be at the correct distance from the screen. The lens may be dirty.
Serial terminal The serial connector which is on the connector panel of the projector conforms to the RS-232C interface specification, so that the projector can be controlled by a personal computer which is connected to this connecter. Connection Serial terminal adapter...
3 bytes (02h) The projector can not receive any command for 10 seconds after the lamp is switched on. Wait 10 seconds before sending the command. If sending multiple commands, check that a response has been received from the projector for one command before sending the next command.
Power condition Input signal Picture mode Shutter function Freeze function SLEEP function Cable specifications (When connected to a a personal computer) Projector 44 - E NGLISH Parameter 000 = OFF VID = VIDEO IN RG1 = PC IN Parameter: NAT=NATURAL...
Menu structure PICTURE Menu ... 28 H PICTURE MODE ... 28 H CONTRAST... 28 H BRIGHTNESS ... 28 H COLOR... 28 H TINT... 29 H SHARPNESS ... 29 H COLOR TEMPERATURE... 29 H DYNAMIC IRIS ... 29 H LIGHT HARMONIZER... 29 H ADVANCED MENU ...
Specifications Power supply Power consumption Amps Panel size (diagonal) Aspect ratio LCD panel Display method Drive method Pixels Lens Lamp Luminosity Horizontal scanning frequency Scanning frequency Vertical scanning (for RGB signal) frequency Dot clock frequency COMPONENT (YP ) signals Color system Projection size Throw distance Screen aspect ratio...
Page 47
S-VIDEO IN VIDEO IN PC IN Connectors COMPONENT IN HDMI IN SERIAL Cabinet Dimensions Weight Operating environment Certifications Power supply Operating range Weight Remote control Dimensions Ceiling bracket Options Projection screen Serial adapter Specifications Single - line, Mini DIN 4p Y: 1.0 V [p-p], C: 0.286 V [p-p], 75 Single - line, RCA pin jack 1.0 V [p-p], 75...
Trademark acknowledgements VGA and XGA are trademarks of International Business Machines Corporation. S-VGA is a registered trademark of the Video Electronics Standards Association. HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC. The font used in the on-screen displays is a Ricoh bitmap font, which is manufactured and sold by Ricoh Company, Ltd.
H- POSITION HDMI ... 18 Connecting ... 34 SIGNAL LEVEL ... 13 Terminal INPUT ... 12 Button on the projector ... 34 INPUT GUIDE ... 11 Remote control button ... 21, 22 Selecting signal ... 35 INSTALLATION ... 15 Projection method ...
Page 51
MAIN POWER ...19 On/Off ...13 Switch MENU ...12 Button on the projector ...26 Main menu ...26 Opening the menu ...11 Remote control button ...30 MPEG NR ...30 NR (Noise Reduction) OPTION ...34 Operation ...27 Sub-menu ...34 OSD DESIGN ...34 OSD POSITION ...33...