Coleman ELITE WEATHERMASTER 2000005748 User Manual

Before you begin
Read all instructions before set up.
• Select a level site clear of rocks, branches, and other hard or sharp
objects, to install your tent.
WARNING: Keep clear of overhead power lines.
• Do not set up your tent under trees because of potential lightning strikes or
falling tree limbs in inclement weather.
• Secure with all stakes and guylines provided to prevent property damage
or personal injury.
• For best results in windy conditions, position narrow end of tent into the wind.
• Enlist the help of at least one other person to assist you when it is time to
assemble the tent.
Pole Descriptions
Description Qty.
Long Leg Pole, steel
(w/ red marking) 4
Short Leg Pole, steel 4
Curved Ridge Pole, steel
(w/ red marking) 2
Curved Ridge Pole, steel 2
Awning Pole, black,
fiberglass, metal tips 2
Door Pole, long, thin, black,
fiberglass, rubber tips 1
Vert. Door Pole, short, black,
fiberglass, rubber tips 1
Self-Rolling Window Spring Descriptions
Color Code Description Qty.
Red
Yellow
Green
Orange
CAUTION: "Springs" may have sharp edges. Handle with care to avoid injury.
Keep out of reach of children.
To Set Up Tent
1. Unfold tent and spread out on a clean, level surface with the door facing
the desired direction. Unzip doors. (Fig. 1)
2. Pull four corners of tent taut, then secure by driving
stakes through web loops at an angle for better
anchoring. (Fig. 2)
3. Assemble four, steel, shock-corded, curved
Ridge Poles. Insert Ridge Poles (with red
marking) into center sleeves on top of tent with
the red trim (Fig. 3). Insert the remaining curved
Ridge Poles into the other two sleeves on top of
tent.
4. Assemble eight, steel, shock-corded, Leg Poles.
Push down on steel button on tapered end and
insert into end with four holes.
NOTE: Make sure steel button locks into third
hole on pole as shown. (Fig.4)
5. Insert curved end of Leg Poles
(with red marking) into the
ends of the Ridge Pole (with
red marking). Insert curved
end of remaining short Leg
Poles into the ends of the
remaining Ridge Poles.
(Fig. 5 & 6)
Fig. 5
ELITE WEATHERMASTER
Pole Pole
Repair Kit Replacement Kit
N/A 5010000754
N/A 5010000755
N/A 5010000756
N/A 5010000757
5010000543 5010000545
5010000543 5010000545
5010000543 5010000545
Replacement Part No.
1 5010000624
2 5010000626
1 5010000627
2 5010000628
Fig. 1
Door
Fig. 2
Fig. 3
Ridge Pole
with Red
Marking
Sleeve
with Red
Trim
Button in third hole
Fig. 4
Ridge Pole with
Red Marking
Sleeve
Curved End of
with Red
Long Leg Pole
Trim
Curved Ridge Poles with Red Markings in center sleeves
6. Rotate all eight Leg Poles upright and insert pin on each
web loop at the side locations as shown. (Fig. 7 & 7A)
7. Locate the plastic hooks at sides and
corners of tent, then snap onto Leg Poles to
attach. (Fig. 8)
8. To stretch tent to fi nished size:
• Push in button on Leg Pole while
twisting lower Leg Pole section
counterclockwise (Fig.9);
• Pull up on top Leg Pole section until
tent is taut;
• Twist the lower Leg Pole clockwise
until the button locks into the center or
lowest hole;
• Repeat on remaining Leg Poles.
9. Insert plastic stakes through web straps located on
both sides of tent, then drive in to secure. (Fig. 10)
NOTE: It may be necessary to remove metal stakes
through web straps at side of tent and screen room,
pull tent taut, and drive in stakes to secure.
Hinged, Rigid Door
1. Assemble Vertical Door Pole (shorter black pole with plastic tips); then insert
through zippered vertical pole sleeve on hinged side of door. (Fig. 11)
2. Insert end of Vertical Door Pole into bottom hinge plate, apply pressure to
form a slight bow, then insert other tip of pole into top hinge. Zip up verti-
cal pole sleeve. (Fig. 12 & 13)
3. Assemble Door Pole (longer black pole with plastic cap tips); then insert
into zippered pole sleeve at top of door. (Fig. 14)
4. Insert end of Door Pole into top hinge plate, apply pressure to form a bow,
then insert other tip of pole into the bottom hinge. (Fig. 15)
5. Zip up pole sleeve to enclose Door Pole. (Fig. 16)
Fig. 11
Vertical Pole
Sleeve
Door Hinge
Fig. 14
Top Top
Door Door
Pole
Pole
Hinge
Hinge
Sleeve Sleeve
(continued on other side)
TENT
®
MODEL 2000005748
Fig. 6
7A
Pin
Fig. 7
Fig. 8
Fig. 9
Upper
Leg Pole
Section
Button
Center Hole
Lower Hole
Lower
Leg Pole
Section
Fig. 10
Fig. 12 Fig. 13
Fig. 15
Fig. 16