Coleman 2000001585 Installation Manual

Before you begin
Read all instructions before set up.
• Select a level site clear of rocks, branches, and other hard or sharp
objects, to install your tent.
WARNING: Keep clear of overhead power lines
• Do not set up your tent under trees because of potential lightning strikes
or falling tree limbs in inclement weather.
• Secure with all stakes and guylines provided to prevent property damage
or personal injury.
• For best results in windy conditions, position narrow end of tent into
the wind.
• Enlist the help of at least one other person to assist you when it is time
to assemble the tent.
Pole Descriptions
Pole
Description Qty. Dia.
Main Poles, long, black 2 11mm
Rainfly Pole, black
w/metal tips 1 11mm
Vertical Door Pole, black,
short w/rubber tips 1 6.3mm
Door Pole, black,
long w/rubber tips 1 6.3mm
Self-Rolling Window Spring Descriptions
Color Code Description Qty.
Green 1
Orange 1
CAUTION: "Springs" may have sharp edges. Handle with care to avoid
injury. Keep out of reach of children.
To Set Up Tent
1. Unfold tent and spread out on a clean, level surface with the door
facing the desired direction. (Fig. 1)
2. Assemble two main tent poles by interlocking the longer, black
shock-corded, poles.
3. Insert both, long, black poles through sleeves in top of tent as
shown. (Fig. 1)
Long, Black,
Shock-corded
Main Poles
Door
Front of Tent
4. Insert one end of each black
pole into pins in front corners of
tent. (Fig. 2)
5. Go to opposite end of each pole and gradually apply pressure to the
pole forming an arch. Insert the pin into the pole end at the corners
of tent. (Fig. 3)
6. Attach frame clips along edges of tent to black main poles.
(Fig. 3A)
ELITE SUNDOME
.
Pole Pole
Repair Kit Replacement Kit
5010000539 5010000549
5010000539 5010000549
501000543 501000545
501000543 501000545
Length Replacement Part No.
550mm 5010000626
670mm 5010000628
Fig. 1
Fig. 2
6 TENT
®
7. Stretch corners and sides of tent until floor is taut then hammer
stakes through loops to secure. (Fig. 3B)
3A
Hinged, Rigid Door
1. Assemble Vertical Door Pole (shorter black pole with plastic tips);
then insert through zippered vertical pole sleeve on hinged side of
door. (Fig. 4)
2. Insert end of Vertical Door Pole into bottom hinge plate, apply
pressure to form a slight bow, then insert other tip of pole into top
hinge. Zip up vertical pole sleeve. (Fig. 5 & 6)
3. Assemble Door Pole (longer black pole with plastic cap tips); then
insert into zippered pole sleeve at top of door. (Fig. 7)
4. Insert end of Door Pole into top hinge plate, apply pressure to form
a bow, then insert other tip of pole into the bottom hinge. (Fig. 8)
5. Zip up pole sleeve to enclose Door Pole. (Fig. 9)
Fig. 4
Vertical Pole
Sleeve
Door Hinge
Fig. 7
Top
Top
Door
Door
Pole Pole
Hinge
Hinge
Sleeve Sleeve
To Attach Rainfly
1. Assemble longer interlocking shock-corded rainfly pole.
2. Unfold rainfly. Locate the sleeve, along front edge, and the hook &
loop fasteners on the underside of Rainfly.
3. Drape Rainfly over tent. Make sure the sleeve is centered over the
door and the hook & loop fasteners, on the seams on underside of
the Rainfly, are
positioned over
the black main
poles.
4. Slide rainfly pole
through sleeve at
front of the Rainfly.
(Fig. 10)
(continued on
other side)
MODEL 2000001585
Fig. 3
Door
3B
Fig. 5 Fig. 6
Fig. 8
Fig. 9
Rainfly
Pole
Rainfly
Sleeve
Door
Fig. 10