Mitsubishi Electric XD300U User Manual page 16

Menu operation (continued)
1 IMAGE
CONTRAST ........ Adjusts the picture contrast. The contrast becomes
higher as the number increases.
BRIGHTNESS .... Adjusts the image brightness. The image becomes
brighter as the number increases.
sRGB ................... Select ON to display an image emphasizing on the color
reproducibility.
• When sRGB is ON, COLOR MATRIX, COLOR
COLOR MATRIX ....... Adjusts the color balance in each color of the image. See page
18.
COLOR TEMP. ... Adjusts the color temperature. See page 18.
COLOR ................ Adjusts the color intensity of the image. (Available only
when VIDEO is selected as the source.)
TINT .................... Adjusts the color balance of the image. The color balance
of the image shifts green as the number increases and
shifts to purple as the number decreases. (Available only
when VIDEO is selected as the source.)
• TINT cannot be adjusted when a TV50 (PAL or
SHARPNESS ...... Adjusts the image sharpness. The image sharpness rises as the number increases.
(Available only when VIDEO is selected as the source.)
GAMMA MODE . Select DYNAMIC for computer sources. Select STANDARD for sport scenes and video
sources. Select THEATER for projecting film sources.
2 INSTALLATION
AUTO POWER ON .... Select ON to boot up the projector automatically by
turning on an externally connected power switch such as
a breaker even when the main power switch of the
projector is off. Use this setting when the projector is
hanging from the ceiling.
• The projector will be in the stand-by mode when the
AUTO POWER OFF .. Set the time elapsed before the projector enters into the
stand-by mode when there is no signal present at the
selected source.
IMAGE CAPTURE .... Capture the screen for Splash screen. See page 23.
SPLASH SCREEN ..... Select ON to display the splash screen when the power is
turned ON.
BACK COLOR .... Select the color of the background to blue or black, this will be displayed when there is no
signal present at the selected source.
MUTE MODE ..... Use to select the background, BLACK or IMAGE, which will be displayed when the MUTE
button is pressed. When the IMAGE is selected, the splash screen will be displayed.
IMAGE REVERSE ..... Use to reverse or invert the projected image. Select MIRROR in rear projection. Select
MIRROR, INVERT in rear projection with the projector hanging from the ceiling.
3 FEATURE
MENU POSITION ..... Use to select the position of the menu on the screen,
UPPER LEFT or LOWER RIGHT.
EXPAND MODE .. Select the mode for enlarging screen. See page 20.
VIDEO MODE .... Use to select the modes of the high quality line doubler.
Select CCS for the Cross Color Suppression mode. Select
CCS+DCDi for the Cross Color Suppression and DCDi
mode. Select DCDi for DCDi mode. Select OFF for
through mode.
• Though square-shaped noise may appear in the
• A playback signal on a deteriorated videotape or a
EN – 16
TEMP or GAMMA MODE can't be adjusted.
SECAM) signal is being displayed.
lamp is off. Use the remote control to turn on the
lamp.
projected image when except OFF is selected, this is
not failure. If it is obtrusive, select OFF. It may take
time to switch from/to OFF. Though the image is not
displayed correctly in this time, it is not a failure.
poor-quality signal may not be projected properly.
When projecting such a signal, change the setting of
the Video mode and check the projection quality.
opt.
TV60
IMAGE
CONTRAST
BRIGHTNESS
sRGB
OFF
OFF
COLOR MATRIX
COLOR TEMP STANDARD
COLOR
TINT
SHARPNESS
GAMMA MODE
DYNAMIC
opt.
TV60
INSTALLATION
AUTO POWER
OFF
ON
AUTO POWER
OFF
OFF
IMAGE
SETUP
CAPTURE
SPLASH
ON
SCREEN
BACK COLOR BLUE
MUTE MODE BLACK
IMAGE
OFF
REVERSE
Opt
TV60
FEATURE
MENU POSITION
UPPER LEFT
A
EXPAND MODE
EXPAND
A
VIDEO MODE
CCS
CINEMA MODE
AUTO
?
VIDEO SIGNAL
AUTO
SCART INPUT OFF
ANAMORPHIC
A Ë
LANGUAGE OK
RESET ALL English
OK
RESET ALL
0
0
0
0
0
ON
OFF