Sign in today to find solutions:

Don't have an account? Sign up

 
DATA PROJECTOR
MODEL
XD300U
XD350U
User Manual
X D300
X D350
EN – 1
Next page ->

Summary of Contents

  • Page 1

    DATA PROJECTOR MODEL XD300U XD350U User Manual X D300 X D350 EN – 1...

  • Page 2

    CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. NOTE: SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET SHALL BE IN- STALLED NEAR THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE. WARNING Use the attached specified power supply cord. If you use another power-supply cord, it may cause interfer- ence with radio and television reception.

  • Page 3: Table Of Contents

    Dimensional drawings ... 29 What’s included in the box ... 29 Replacement part ... 29 Specification of RGB signals in each computer mode of the projector ... 30 Trademark, Registered trademark Macintosh is registered trademark of Apple Computer Inc. DLP, Digital Micromirror Device and DMD are all trademarks of Texas Instruments.

  • Page 4

    Water and moisture Do not use this projector near water or in con- tact with water. Accessories Do not place this projector on an unstable cart, stand, tripod, bracket or table.

  • Page 5

    • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced Radio / TV technician for help. Changes or modifications not expressly approved by Mitsubishi could void the user's authority to operate this equipment. COMPLIANCE NOTICE OF INDUSTRY CANADA This Class B digital apparatus complies with Canadian ICES-003.

  • Page 6: Overview

    Overview Control panel POWER LAMP/TEMP STATUS COMPUTER AUTO POSITION POWER KEYSTONE/ VIDEO Terminal board VIDEO 2 VIDEO 1 S-VIDEO MAIN AC IN VIDEO COMPUTER AUDIO IN AUDIO EN – 6 Air inlet grille (Front) Lens Foot adjustment buttons Air inlet grille (Side) Kensington Security Lock Standard connector Speaker Control panel...

  • Page 7

    • Use of controls or adjustments or procedures other than those specified herein may IEC 60825-1:1993+A1:1997 Rear adjustment feet Lamp cover Front adjustment feet Caution: Do not replace the lamp right after using the projector. The lamp is very hot. Laser aperture Transmission window Indicator POWER button...

  • Page 8: Using The Remote Control, Battery Installation

    The range for operation is about 10 m (33 feet) when the remote control points to the projector. The distance to the screen back to the projector must be less than 6 m (20 feet). Depending on the type of screen, the effective distance may be different.

  • Page 9: Installation

    Installation Orientation of the projector Picture size can be set by changing the distance between the screen and the projector. Front projection Screen (between the screen and the head of the projector) Screen Diagonal size Width (inch) (cm) (inch) (cm) 40 "...

  • Page 10: Basic Connections, Projector + Av Equipment, Projector + Dvd Player Or Hdtv Decoder

    Basic connections This projector can be connected to equipment such as PC, VCRs, video cameras and DVD players. Important: • Make sure that your equipment is turned off before connection. • Plug in firmly and unplug by holding the plug, not by pulling the AC power cord.

  • Page 11: Projector + Personal Computer

    • You may need to install the DDC driver, depending on the computer you use. In this case, you need to download the driver from our Web site. Contact your dealer or Mitsubishi sales office for further information. RGB cable for PC...

  • Page 12: Preparing The Projector For Operation

    2. Connect the power cord to the wall power outlet. 3. Remove the lens cap. Warning: • Do not look directly into the lens when projector is “ON”. • The lens cap is for protecting the lens. If you leave the power on with the cap on, the cap may be warped.

  • Page 13: To Operate Projector Power On

    AUDIO 3 • 7 • 8 1. Turn on the equipment connected to the projector. 2. Put the projector into standby mode by pressing the main power switch. The POWER indicator lights up red. 3. Turn the projector on by pressing the POWER but- ton.

  • Page 14

    It will take another 60 seconds before the STATUS indicator goes off. If you wish to turn on the projector again, wait until the indicator is off then press the POWER button. • The exhaust fan rotates faster when the tempera- ture around the projector rises.

  • Page 15: Menu Operation

    Menu operation IMAGE COLOR MATRIX GAMMA MODE INSTALLATION AUTO POWER ON AUTO POWER OFF IMAGE CAPTURE SPLASH SCREEN IMAGE REVERSE FEATURE MENU POSITION EXPAND MODE CINEMA MODE VIDEO SIGNAL SIGNAL HORIZ.POSITION VERT.POSITION * 1: The item can not be selected when the sRGB is set to ON. * 2: The item can not be selected with certain signals.

  • Page 16

    • The projector will be in the stand-by mode when the lamp is off. Use the remote control to turn on the lamp. AUTO POWER OFF .. Set the time elapsed before the projector enters into the stand-by mode when there is no signal present at the selected source.

  • Page 17

    • Use optional SCART-Mini D-SUB 15P cable, when connecting with AV device equipped with the SCART terminal. • Some AV devices equipped with the SCART terminal may not be compatible with the projector. • When VIDEO SIGNAL is set to AUTO, the image may not be projected with correct colors. Change the setting of VIDEO SIGNAL depending on the input signal in such cases.

  • Page 18: Picture Adjustment

    Picture adjustment Adjusting the image You can adjust the picture by using the IMAGE menu. opt. TV60 IMAGE CONTRAST BRIGHTNESS sRGB COLOR MATRIX COLOR TEMP STANDARD COLOR TINT SHARPNESS GAMMA MODE DYNAMIC To control the level of white-to-black in the image : Adjust CONTRAST in the IMAGE menu.

  • Page 19

    Adjustment from personal computer This projector should automatically display the full computer image on the projection screen. However, with some computers signals this may not occur, in this case press the AUTO POSITION button. If the images are still not projected correctly, use the MENU display to adjust the projected images.

  • Page 20: Advanced Features, Expand, Picture In Picture (pinp), Still

    Advanced features Expand By pressing the EXPAND button on the remote con- trol, you can magnify the detailed image of the picture. Using the Expand mode 1. Press the EXPAND button. • You can magnify different areas of the active pic- ture by pressing the {, }, $, % button.

  • Page 21: Mouse Remote Control

    MOUSE / RS-232C terminal • Turn off the PC and the projector before connecting to the PCs PS/2 port. If you connect the PS/2 cable when the personal computer is on, the remote control mouse may not work. In that case, turn the projector on, then restart the personal computer.

  • Page 22: Installation Other Device's Remote Commands

    1. Set the SELECT switch of the remote control of this projector to DVD or VIDEO, depending on the device you use. 2. Place the remote control of this projector and that of the other device with their transmission windows 2-5 cm apart.

  • Page 23: How To Change The Image Displayed At The Time Of Startup Or Mute

    8. Select SIZE by pressing the { or } button. 9. Select x1, x2, or FULL by pressing the $ or % button. EXAMPLE : For XD300U Capture the image 10.Select CAPTURE by pressing the { or } button. 11.Press the ENTER button.

  • Page 24: Lamp Replacement

    • Be sure that the projector guide is firmly inserted between the right and left lamp guides. Important: • The projector will not turn on if you do not secure the lamp lid. • You must reset the operation time meter after you replace the lamp.

  • Page 25: Maintenance

    Maintenance Caution: Be sure to turn off the projector and unplug the power cord from the wall outlet before you perform any main- tenance on the projector. Cleaning the air-filter Clean the air-filter frequently (at least once a month). If the filter or ventilation slots become...

  • Page 26: Indicators

    Indicators The projector has two LED Indicators which show the working condition of the projector. The below table offers solutions to possible problems. If a problem persists, turn the projector off and consult your dealer. Normal condition Power STATUS CONDITION...

  • Page 27: Troubleshooting

    The image is clogged with dust or obstructed. turned off. (In this case, the STATUS indicator does not light up.) • The projector is not at a right angle to the screen. The image is distorted. The image is dark.

  • Page 28: Specifications, Kensington Lock

    (performance guarantee) Kensington Lock This projector has a Kensington Security Standard connector for use with a Kensington MicroSaver Security System. Refer to the information that came with the Kensington System for instructions on how to use it to secure the projector. Please contact to Kensington Technology Group as shown below.

  • Page 29: Connectors, Dimensional Drawings, What's Included In The Box, Replacement Part

    1 USB adapter cable 1 Remote control Replacement part (Option / Not included in the box) Spare Mercury lamp (For XD300U) RS-232C input Use to control the projector with the personal computer, or control the personal computer with remote control.

  • Page 30: Specification Of Rgb Signals In Each Computer Mode Of The Projector

    Specifications (continued) Specification of RGB signals in each computer mode of the projector Signal mode resolution (H x V) TV60 – TV50 – 525p – 625p – 1080i – 1080i50 – 1080i50a – 720p – 720p50 – PC98 640 x 400...

  • Page 32

    :projector.info@meuk.mee.com Technical Phone :+44 (870) 606 5008 :+44 (1506) 431927 E-mail :projector.info@meuk.mee.com Russia (Mitsubishi Electric Europe B.V Moscow Representative Office) 52, bldg.5, Kosmodamianskaya Nab, 113054, Moscow, Russian Federation Sales Phone :+7 (095) 721 2070 :+7 (095) 721 2071 Technical Phone...

Comments to this Manuals

Symbols: 0

Latest comments:

×

Select the desired size and copy embed code

Copy your embed code and put on your site: