Page 1
26" LCD HDTV With Built-in DVD Player DTV-265-D OWNER'S MANUAL...
Page 2
IMPORTANT SAFETY PRECAUTIONS • If an outside antenna is connected to the television equipment, be sure the antenna system is grounded so as to provide some protection against voltage surges and built-up static charges. Section 810 of the National Electrical Code provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, Iocation of antenna-discharge unit, connection to grounding electrodes,and requirements for the grounding electrode.
TABLE OF CONTENTS (FOR TV TUNER) IMPORTANT INFORMATION IMPORTANT SAFETY PRECAUTIONS SUPPLIED ACCESSORIES PREPARATION INSERTING BATTERIES INTO THE REMOTE CONTROL ● USING THE REMOTE CONTROL UNIT ● CAUTIONS REGARDING REMOTE CONTROL UNIT ● DISPLAY FRONT VIEW ● REAR VIEW ●...
Page 4
TABLE OF CONTENTS (FOR DVD PLAYER) BASIC OPERATIONS PLAY DISCS ● PAUSE ● ● VOLUME CONTROL ● DVD MENU PLAY ● SELECT WITH NUMBER BUTTONS ● PLAY DISCS IN VARIOUS WAYS AUDIO MODE ● MUTE ● FAST PLAY ● REPEAT PLAY ●...
● Correct the equipment into an outlet on a circuit different from that to which the receiver ● is connected. Consult the dealer or an experienced radio, TV technical for help. ● Only shielded interface cable should be used. ●...
IMPORTANT SAFETY PRECAUTIONS The present set has been designed and manufactured to assure personal safety. Improper use can result in electric shock or fire hazard. The safeguards incorporated in the present unit will protect you if you observe the following procedures in installing, using and servicing. The present unit is fully transistorized and does not contain any element that can be repaired by the user.
17. Water and moisture - Do not use this product near water such as bathtub, washbasin, kitchen sink and laundry tub, swimming pool and in a wet basement. TV set shall not be exposed to dripping or slashing and no objects filled with liquid, such as vases, shall be placed on the TV set.
VIEW MODE VIEW MODE RC-600B Remote control It also include: ①batteries (2) ②Warranty card AV cables Audio cable for PC input page4 Component Video Cable or Y/Pb/Pr cable 26" LCD HDTV With Built-in DVD Player DTV-265-D OWNER'S MANUAL User guide...
TV. Objects between the remote control and the sensor may disrupt operation. Effective range is 20 feet but is dependant on what your ● viewing angle is. Range can also be affected by direct sunlight on the TV's ● sensor. page5...
12) PREV: Use to skip to the previous chapter. 13) NEXT: Use to skip to the next chapter. 14) EJECT BUTTON: Use to eject the disc being played in the disc slot. And the TV set returns to the previous status.
DISPLAY REAR VIEW DV I HDMI AUDIO R S 2 3 2 INPUT INPUT DVI INPUT 1) DVI Input 2) HDMI Input 3) AUDIO (DVI Input) 4) RS-232 Terminal 5) Component Video (Y、P 6) INPUT1(Composite Video, S-Video and Audio Input) 7) Audio Output 8) Antenna In 9) INPUT2 (Composite Video and Audio Input)
4) Number Buttons: Use to set the channel numbers. Dot Button: In Digital TV mode, there can be several TV programs in a channel, use the number buttons and the dot button to enter. Example: press the number button 5, the dot button, and then the number button 2 to enter the TV program 5-2.
18) VIEW MODE: Use to select a viewing mode. 19) OSD: Use to bring up the DVD on screen display. 20) EJECT BUTTON: Use to eject the disc being played in the disc slot. And the TV set returns to the previous status.
CONNECTIONS DV I HDMI AUDIO INPUT INPUT DVI INPUT DVI Audio Cable AUDIO VIDEO R S 2 3 2 S-VIDEO INPUT INPUT 1 page10 VIDEO AUDIO INPUT 2 AUDIO A N T. I N OUTPUT...
DTV-265-D. Use the VIDEO button and the signal source to “HDMI” . g. Using the DVI connector: Connect a PC computer to the DTV-265-D through the DVI socket on DTV-265-D. The Mini-plugged is for audio associated with this type of signal. Use the...
BASIC OPERATIONS TURN ON THE POWER 1. Press POWER button on the front panel to turn on the TV set. The POWER indicator lights up green. 2. If the STANDBY indicator still lights up red, press POWER on the remote control to turn the TV set on.
WATCHING TV TURN ON THE POWER 1. Press POWER button on the front panel to turn on the TV set. The POWER indicator lights up green. 2. If the STANDBY indicator still lights up red, press POWER on the remote control to turn the TV set on.
WATCHING TV Using number buttons on the remote unit NUMBER BUTTONS Select the channels directly by pressing the number buttons. EXAMPLE: To select a 1-digit channel (e.g. channel 2): Press 2 . ● To select a 2-digit channel (e.g. channel 12): Press 1 ,followed by 2 .
E Displays the start and end times of the selected digital programs. Note: The availability of details depends on the broadcaster. When the TV program being played was forbidden to play for parental control, the EPG button is not available.
This feature is called Multi-channel Television Sound (MTS). The System with MTS can receive mono sound, stereo sound and Secondary Audio Programs (SAP). The SAP feature allows a TV station to broadcast other information, which could be audio in another language or something completely different like weather information.
You can get the satisfied picture by adjusting the following Video menu. Press the VIEDO button to select various signal modes. Press the TV MENU button to enter LCD menu. Press to select "VIDEO MENU", and then press OK or Brightness 1.
2. Press to select a Temperature Mode among: Cool, Normal, Warm, and User. When "User" is selected, the screen shows: 3. Press to select "Temperature (R)", "Temperature (G)", "Temperature (B)", and press adjust. 4. Press TV MENU to exit. page18...
AUDIO MENU Adjust the quality of the sound through the following Audio menu. Press the VIDEO button to select various signal modes. Press the TV MENU button to enter LCD menu. Press to select "AUDIO MENU", and then press OK or Treble 1.
2. Press OK to enter the Horizontal Position menu. 3. Press to adjust the horizontal position of the playback picture. 4. Press OK to return; press TV MENU to exit. Vertical Position 1. Press to select "Vertical Position" in "Screen" menu.
4. Press TV MENU to exit. Example: 1. In analog TV mode, it is need to select Favorite Mode Off by pressing FAVORITE button and then enter into the “channel menu” after searching all the TV program. 2. Press OK or to select “ANALOG”...
Page 26
2. Press OK to enter the "Fine Tune" menu. 3. Press to adjust the current channel clearer as your desired. 4. Press OK to return; press TV MENU to exit. NOTE: "Fine Tune" only works on Analog TV channels. page22...
BASIC ADJUSTMENT SETTINGS SETUP MENU 1. Press the TV MENU button to enter LCD menu. 2. Press to select "SETUP MENU", and then press OK or Language 1. Press to select "Language" in "Setup" menu. 2. Press to select a language.
3. Press TV MENU to exit. Note: a. Only in Digital TV mode, digital CC is available. b. In digital TV mode, the "Analog CC" is preferential. If you want to view "Digital CC", only set "Analog CC" to "OFF" in CLOSED CAPTION MENU.
Page 29
"Font Style" in "Closed Caption" menu. 2. Press to select a font style among: Default, Style1, Style2, Style3, Style4, Style5, Style6 and Style7. 3. Press TV MENU to exit. Foreground Color 1. Press to select "Foreground Color" in "Closed Caption" menu.
BASIC ADJUSTMENT SETTINGS PARENTAL MENU Only in Digital TV, Analog TV, Composite and S-Video mode, there is Parental menu. 1. Press the TV MENU button to enter LCD menu. 2. Press to select "PARENTAL MENU", and then press OK or The password menu displays.
Page 31
"Change Password" in "Parental" menu. 2. Press OK to display the Change Password menu. 3. Enter your new password with numbers, then input it again and press OK to confirm. 4. Press TV MENU to exit. MPAA (Movie Rating) 1. Press to select "MPAA"...
Page 32
2. Press OK to display the TV Guidelines menu. 3. Press to select desired US-TV position and press OK to confirm. When setting an individual content-based rating items, do as follows: to access block content items from the currently selected age-based rating item.
WINDOW ADJUSTMENT In PC mode you have to set the Windows system firstly as below. SVGA WXGA NOTE: If the PC resolution is set higher than what is listed on the chart, the monitor will display a black screen. The effect will be optimum when the freguency you selected is 60Hz. Setup your PC software…...
WINDOW ADJUSTMENT 2. Click on "Control panel", the control panel screen appears. 3. Double click on "Display" and a display dialog box displays. 4. Navigate to the "Setting " tab on the display dialog box .Set the "Screen resolution" to "1024×768 pixel".
Reception. If so, change the mode to Mono. - Check if the batteries in the Remote control die. Remote control does - Check if any object between IR sensor of the TV and the Remote not work. control does not obstruct.
VIEWING ANGLE (H/V) CONTRAST RATIO BRIGHTNESS (cd/m2) EFFECTIVE PIXEL RATE WITHOUT STAND DIMENSION WITH STAND WITHOUT ST WEIGHT WITH STAND TV STANDARD TUNING SYSTEM TV-FUNCTION FREQUENCY RANGE CATV DIGITAL TERRESTRIAL BROADCAST (8VSB) DIGITAL CABLE(64/256QAM) ANALOG TERRESTRIAL INPUT POWER SOUND OUTPUT...
4. The unit begins to read the disc. 5. Press (PLAY) to play the disc. AFTER STEP 4 IS FINISHED: If playing a DVD, the TV screen shows DVD menu or ● title menu. If playing a CD, press (PLAY), and the unit plays ●...
Page 38
BASIC OPERATIONS (FOR DVD PLAYER) Remember, you can only access the Display when you're playing a disc. Also, the Display features are only available if the disc was created with that particular feature (i.e., if you select the Subtitle icon, you won't be able to change the subtitle language unless the author of the disc created the disc with subtitles).
Page 39
BASIC OPERATIONS (FOR DVD PLAYER) 1. When the disc is playing, press OSD on the remote to bring up the Display. 2. Press the buttons to highlight the Subtitle icon. 3. Press the buttons to scroll through the subtitle languages that are available on the disc until the subtitle language you want to use appears in the text box.
Repeat options until the Repeat option you want is displayed in the text box. 4. The selected repeat option will loop repeatedly until you turn Repeat off. Volume Control Press VOLUME on the TV or amplifier to adjust the ● volume. Press VOLUME on the remote control. ●...
BASIC OPERATIONS Select with Number Buttons Load a disc. Press number buttons to select tracks after the unit finishes reading the disc. 1. If the track number isn't over 10, just push buttons 1-10. Example: push 8 to select track 8. The screen shows: TRACK08/20 00:00...
PLAY DISCS IN VARIOUS WAYS Fast Play When playing a disc, you can play it in fast-forward or fast-reverse mode to find what you want to view. DVD OR CD 1. While disc is playing, press to play in fast-forward mode.
PLAY DISCS IN VARIOUS WAYS REPEAT 2. To repeat a disc: Press REPEAT , the screen shows " The unit plays all the tracks on the disc. REPEAT 3. To remove "REPEAT" function: Press REPEAT till " ALL" disappears. Zoom Play This function can be used to watch a motion or motionless picture.
PLAY DISCS IN VARIOUS WAYS Program Play PREV NEXT ZOOM AUDIO PLAY MODE SUBTITLE PLAY MODE RC-600B To use the program playback feature, you must enter the order in which you want the titles (and chapters) on the DVD or the tracks on the CD to play by creating a program.
PLAY DISCS IN VARIOUS WAYS Shuffle (Random) Play The unit can play DVD chapters or audio tracks in random order. The order is different each time. 1. Press PLAY MODE to select shuffle or random play mode when a disc is playing. PLAY MODE The screen shows: SHUFFLE...
MENU SETTING According to the recorded information and external equipment, set the following functions for the player to obtain the best playing status. TITLE PREV NEXT ZOOM SETUP AUDIO REPEAT PLAY MODE SUBTITLE EJECT VIEW MODE VIEW MODE RC-600B 1.Press SETUP to set options in the main menu. SETUP The main menu appears on the screen, with icons across the top of the screen, illustrating General Setup, Audio...
Wide-screen images are shown on the screen, but with some parts cut automatically. 2. NORMAL/LB This is selected when the unit is connected to a normal TV. Wide-screen images are shown on the screen with black bars on the top and bottom of the screen. 3. WIDE This is selected when the unit is connected to a wide-screen TV.
SCREEN SAVER The screen saver image appears when the unit stops or the image is frozen for a few minutes. The screen saver prevents damage to the TV screen. ON: Start the screen saver. ● OFF: Remove the screen saver.
MENU SETTING ■ 3D PROCESSING The setting structure is: - - 3D Processing Page - - V SURR Reverb Mode Concert Living Room Hall Bathroom Cave Arena Church Audio Setup V SURR ● Use to turn the above function off. REVERB MODE ●...
MENU SETTING Preferences The setting structure is : - - Preference Page - - Audio English French Spanish Chinese Japanese Subtitle English French Spanish Chinese Japanese Disc Menu English French Spanish Chinese Japanese Parental 1 KID 3 PG 4 PG 13 5 PGR 7 NC17 8 ADULT...
If you experience the following problems while using the unit, this troubleshooting guide can help you. No sound Check if the unit is connected securely. ● Make sure the TV or amplifier is working properly. ● Make sure the amplifier is set to receive DVD signal ●...
TECHNICAL SPECIFICATIONS Laser Video system Frequency response Signal/noise ratio Audio distortion + noise Channel separation Dynamic range Audio out (analog audio) Output Video out Power supply Power Consumption This manual is only for your reference, any change to the design and specifications will not be advised. Wavelength 650nm NTSC 20Hz ~ 20KHz±2.5dB...