Miele KM 404 Installation Instructions Manual
Miele km404 cooktops: install guide
Hide thumbs
Also See for KM 404:
- Installation instructions manual (40 pages) ,
- Operating instructions manual (20 pages) ,
- Dimension manual (1 page)
Related Manuals for Miele KM 404
Summary of Contents for Miele KM 404
-
Page 1: Installation Instructions
Installation Instructions Gas Cooktop KM 404 KM 406 ® ® To prevent accidents and machine damage, read the operating instructions before installation or use. M.-Nr. 05 060 881... - Page 2 WARNING: If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury or death. – Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
-
Page 3: Table Of Contents
Contents IMPORTANT SAFETY INSTRUCTIONS ....... . . 4 Cooktop dimensions ..........6 KM 404. -
Page 4: Important Safety Instructions
However, under certain circumstances it may be possible for installation in these applications. Please contact a Miele Dealer or Miele’s Technical Service Department with specific requirements. recommended not recommended not allowed... - Page 5 The heat generated by cooktops could damage these appliances. Deep fryers must not be installed next to gas cooktops. Gas flames can ignite splattering oil. A distance of at least 12" (305 mm) should be maintained between these two appliances.
-
Page 6: Cooktop Dimensions
Cooktop dimensions KM 404 a Support brackets b Building in height plus the fixing screws * Please allow an additional 3 (90 mm) depth across the rear of the cooktop for clearance of the gas regulator (see "Gas connection" for illustration). - Page 7 KM 406 a Support bracket b Building in height plus the fixing screws * Please allow an additional 3 (90 mm) depth across the rear of the cooktop for clearance of the gas regulator (see "Gas connection" for illustration). " (3 mm) for "...
-
Page 8: Countertop Cut-Out
Countertop cut-out All Miele combisets have the same length and width. Make sure that there is enough room under the countertop to allow for the depth of the various appliances. Remember to allow clearance for the gas regulator and gas pipe that must be connected to the appliance. -
Page 9: Installation
Laying out the support bars and brackets a Support brackets b Support bars c Slight gap between support bar and countertop d Bracket center line The illustration shows the layout for three combisets and their respective support bars, b, and support brackets, a, required for correct installation. -
Page 10: Securing The Support Brackets
Installation Securing the support bars Wood or Corian countertops ^ Arrange the bars, b, as shown in the illustration. ^ Drill " (1.5 mm) pilot holes through the brackets and secure them using the supplied screws. ^ Fill the gap, c, between the bars and the countertop using the supplied silicon sealant. -
Page 11: Setting The Cooktop Into Place
Any pipe connections must be made using a thread sealant approved for gas connections. Failure to correctly install these items could lead to a gas leak and subsequent explosion. Setting the cooktop into place ^ Screw the gas regulator onto the nipple underneath the cooktop. - Page 12 Installation Important The cooktop must not be permanently sealed into the countertop when installed. The sealing strip under the edge of the cooktop provides a sufficient seal for the countertop. If the cooktop is sealed into position, the countertop or the appliance may be damaged if the cooktop needs to be removed for maintenance or service.
-
Page 13: Electrical Connection
This appliance must be electrically grounded according to local or national codes. All electrical work should be performed by a qualified electrician in accordance with local codes and the: National Electrical Code ANSI / NFPA No. 70 for the USA Canadian Electrical Code Part I for Canada (CSA Standard C 22.1). -
Page 14: Gas Connection
Gas connection Installation and service must be performed by a qualified installer, service agency or the gas supplier. In Massachusetts a licensed plumber/gas fitter is required. This appliance must be installed with its own shut off valve and the included gas pressure regulator. Both the valve and the regulator must be easily accessible to the consumer to turn on or shut off the... -
Page 15: Gas Pressure Regulator
½" NPT c Regulator As shown in the above diagram, the included regulator must be used when connecting the Miele cooktop to your gas supply. This item has been customized by Miele to meet all applicable safety requirements. Make... -
Page 16: Nominal Ratings
Gas connection Nominal ratings KM 404 Front burner BTU/hr Maximum output Minimum output Rear burner Maximum output 10000 Minimum output KM 406 BTU/hr Maximum output 17500 Minimum output 6000 1.75 1000 0.29 2.93 1600 0.47 5.13 0.18... -
Page 17: Converting To Another Type Of Gas
If the appliance is to be connected to a type of gas other than it was originally configured for, both the regulator and burners must be converted. A conversion kit is available as an optional accessory from the Miele Technical Service Department. - Page 20 Alterations rights reserved / 3606 M.-Nr. 05 060 881 / 05 en - USA...