McCall LBR-2D-LT Specifications

LBS-4D-LT
McCall Refrigeration specification sheets are available
online @ www.mccallrefrigeration.com
Stainless Steel Equipment Top - One-piece, heavy
reinforced, sanitary stainless steel top with integral drip-
proof 1/4" high "V" edge (4) sides to protect against
spills. Front to extend beyond drawers and hardware.
Sub-Top - Heavy gauge galvanized sub-top.
Interior Lining - The interior shall be all aluminum, cove-
corner construction, with all joints completely closed and
sealed. Interior top and bottom shall be one-piece, die-
stamped, with 3/8" radius bends and coved corners.
Refrigerated Drawers - Drawers are specially designed
for storage of food products. They are to be self-closing,
full-access, lift-out type of ball bearing and tracks.
Drawer fronts to be stainless steel with stainless steel,
heavy-duty, recessed pull handles and self-adjusting, full
perimeter magnetic gaskets for a positive seal. Gaskets
removable for ease of cleaning. Drawer fronts to be
insulated with "one-shot," high-pressure, poured-in-
place polyurethane. Each drawer to accommodate two
12" x 20" x 4" deep stainless steel cafeteria pans. (Pans
supplied by others) Positioning of full size pans in the
drawer is side to side. Interior pan frame supports to be
stainless steel.
Phone (731) 847-5570 / Fax (731) 847-9012 / 1-888-REACH-IN (1-888-732-2446) / www.mccallrefrigeration.com
CLASSIFIED TO
NSF (STD-7-1999)

SPECIFICATIONS

Drawer Openings - Drawer openings to have full-
perimeter, non conductive, hi-impact structural, double-
wall, safety-bevel, breaker strips to prevent heat transfer
between the metal interior liner and the outer cabinet.
There shall be no metal-to-metal contact between the
inner liner and the outside cabinet. They shall have no
exposed screws or fasteners and shall have a smooth,
sanitary, finished surface. Openings to have full-
perimeter, minimum-wattage, anti-condensate heaters
located behind the stainless steel front fascia of the
cabinet to retard condensation. The heaters shall be
indexed within the double-wall breaker for positive
location and maximum efficiency.
Legs - Sturdy 6" high threaded single stud quick mount
sanitary adjustable "non-mar" legs are furnished as
standard, (6) legs on two drawer models and (8) legs on
four and (10) legs on six drawer models. Heavy-duty
swivel casters with locking feature optional at extra cost.
Condensate evaporator - Sanitary, removable, automatic
electrical condensate evaporator mounted in machine
compartment for easy access. No plumbing connections
or floor drains required.
McCall Refrigeration / 81 West Holly Street / Parsons, TN 38363
January 2007 / Printed in U.S.A.
ITEM #
MODEL #
PROJECT NAME
L B
OW OY
LBS-2D-LT, LBS-4D-LT, LBS-6D-LT
Sub-top, flat (galvanized)
Models: Remote
LBR-2D-ST, LBR-4D-ST, LBR-6D-ST
Stainless steel top with "V" edge
LBR-2D-LT, LBR-4D-LT, LBR-6D-LT
Sub-top, flat (galvanized)

Standard Features

• "One-shot" high pressure foamed-in-place polyurethane insulation
• Automatic defrost system
• Stainless steel fronts, drawers and exterior ends
• Full pan accessibility and capacity with 20" drawers
• Rugged, self-closing insulated drawers on heavy-duty ball roller ball
bearing tracks
• Self-closing drawers with safety stops and stay open features
• High humidity mullion diffusers
• One-piece removable magnetic gasket
Approval :
Evaporator coil - Four and six drawer models equipped
with vertical, forced air, evaporator coil located behind
mullion(s) for maximum circulation. One evaporator in
four drawer cabinets, two in six drawer cabinets. Two
drawer model has space saver evaporator blower.
Refrigeration System - Self Contained Models -
Hermetic system with R-134a refrigerant. Capillary
metering device, automatic adjustable thermostat system
and cabinet designed to maintain an average
temperature of 38°F average internal air temperature.
Condensing Unit - Air-cooled, hermetic condensing unit
installed in machine compartment can slide-out for ease
of cleaning and maintenance. Cabinet designed to allow
placement against rear wall.
Refrigeration System - Remote Models -- All remote
cabinets are those having the condensing unit located
beyond the confines of the cabinet (field installation).
The cabinet is furnished with a evaporator blower
assembly, thermostat, expansion valve (R-134a) and
solenoid, valve only. The condensing unit, receiver,
controls, tubing and installation are not included. Sizes
of condensing unit shall be by others in accordance with
McCall recommendations.
AIA #
SIS #
C S
HEF TANDS