Mitsubishi Electric GOT1000 GT1595-XTBA General Description

GT15 General Description
GT1595-XTBA GT1595-XTBD GT1585V-STBA GT1585V-STBD
GT1585-STBA GT1585-STBD GT1575V-STBA GT1575V-STBD
GT1575-STBA GT1575-STBD GT1575-VTBA GT1575-VTBD
GT1565-VTBA GT1565-VTBD GT1575-VNBA GT1575-VNBD
GT1572-VNBA GT1572-VNBD GT1562-VNBA GT1562-VNBD
GT1555-VTBD GT1555-QTBD GT1555-QSBD GT1550-QLBD
Thank you for purchasing the GOT1000 Series.
Prior to use, please read both this manual and the
detailed manual thoroughly to fully understand the
product.
MODEL GT15-U-GD-E
Model
1D7MP8
code
IB(NA)-0800546ENG-A(1410)MEE
SAFETY PRECAUTIONS
(Always read these precautions before using this equipment.)
Before using this product, please read this manual and the relevant
manuals introduced in this manual carefully and pay full attention to
safety to handle the product correctly.
The precautions given in this manual are concerned with this prod-
uct.
In this manual, the safety precautions are ranked as "WARNING"
and "CAUTION".
Indicates that incorrect handling may cause
WARNING
hazardous conditions, resulting in death or
severe injury.
Indicates that incorrect handling may cause
CAUTION
hazardous conditions, resulting in medium or
slight personal injury or physical damage.
Note that the CAUTION level may lead to a serious accident
according to the circumstances.
Always follow the instructions of both levels because they are impor-
tant to personal safety.
Please save this manual to make it accessible when required and
always forward it to the end user.
[DESIGN PRECAUTIONS]
WARNING
 Some failures of the GOT, communication unit or cable may keep the outputs
on or off.
Some failures of a touch panel may cause malfunction of the input objects
such as a touch switch.
An external monitoring circuit should be provided to check for output signals
which may lead to a serious accident.
Not doing so can cause an accident due to false output or malfunction.
 If a communication fault (including cable disconnection) occurs during
monitoring on the GOT, communication between the GOT and PLC CPU is
suspended and the GOT becomes inoperative.
For bus connection : The CPU becomes faulty and the GOT becomes
inoperative.
For other than bus connection : The GOT becomes inoperative.
A system where the GOT is used should be configured to perform any
significant operation to the system by using the switches of a device other
than the GOT on the assumption that a GOT communication fault will occur.
Not doing so can cause an accident due to false output or malfunction.
 Do not use the GOT as the warning device that may cause a serious
accident.
An independent and redundant hardware or mechanical interlock is required
to configure the device that displays and outputs serious warning.
Failure to observe this instruction may result in an accident due to incorrect
output or malfunction.
Manual
The following shows manuals relevant to this product.
Detailed Manual
Manual number
Manual name
(Model code)
GT15 User's Manual
SH-080528ENG
(Sold separately) (1D7M23)
For detailed manuals, refer to the PDF manuals stored in the DVD-ROM for the
drawing software used.
Relevant Manuals
For relevant manuals, refer to the Help or the PDF manuals stored in the DVD-
ROM for the drawing software used.
The latest manuals are also available from MITSUBISHI ELECTRIC FA Global
Website (http://www.MitsubishiElectric.co.jp/fa/).
© 2014MITSUBISHI ELECTRIC CORPORATION
Before using the GOT
Connect the connector of the GOT to the connector of the battery.
For details on GT15 specifications, installing procedure, EMC Directive, wiring,
maintenance and inspection, or checking method for the version and the
compatible standard, refer to GT15 User's Manual.
Packing List
The GOT product package includes the following:
Model name Product
GOT
Installation fitting
GT1595-X
GT15 General Discription
GT15 本体概要説明書
GT1585V-S
GOT
GT1585-S
GT1575V-S
GT1575-S
Installation fitting
GT1575-V
GT1575-VN
GT1572-VN
GT1565-V
GT15 General Discription
GT1562-VN
GT1555-V
GT1555-Q
GT15 本体概要説明書
GT1550-Q
1. FEATURES
(1) Improved monitoring performance and connectivity to FA devices
• Using of TFT color liquid crystal display (high intensity, wide angle view and
high definition type) provides clear full-color display and displays small
characters clearly. (Displays digital images of BMP and other formats in
*1
65536 colors.)
• Provides multi-language display function based on Unicode2.1 True Type
font and high-speed drawing of beautiful text.
• High speed monitoring through high speed communication at maximum of
115.2kbps.
• High speed display and high speed touch switch response.
(2) More efficient GOT operations including screen design, startup, adjustment,
management and maintenance works
• 9MB user memory is included as standard. (Memory capacity can be
expanded up to 57MB by increasing the option memory)*1
• CF card interface is included as standard.
• Font installation is available to increase the system fonts.
• Combined use of 4 types of alarms (system alarm, user alarm, alarm
history, alarm popup display) realizes more efficient alarm notification.
• Maintenance timing report function is available that measures the backlight
energization time and notifies of maintenance time.
• The USB connector is positioned on the GOT front. This enables the system
startup to be performed more efficiently using FA device startup tool, and
eliminates the necessity of indirect works (opening and closing the control
panel, cable replacement, cable rewiring) in order to improve the working
efficiency.
• The blown backlight bulb can be confirmed even during screen saving, with
the blinked POWER LED at backlight shutoff detection.
(3) Enhanced support of FA device setup tools
• Transferring and monitoring sequence programs with the personal computer
connected to the GOT can be executed when connecting to a PLC CPU
with the direct CPU connection or bus connection. (FA transparent function)
*1: The specifications differ depending on the GOT to be used.
For the specifications, refer to the GT15 User's Manual.
[DESIGN PRECAUTIONS]
1
WARNING
2
 Incorrect operation of the touch switch(s) may lead to a serious accident if the
3
GOT backlight is gone out.
4 When the GOT backlight goes out, the POWER LED flickers (green/orange)
and the display section turns black and causes the monitor screen to appear
5
blank, while the input of the touch switch(s) remains active.
6 This may confuse an operator in thinking that the GOT is in "screensaver"
mode, who then tries to release the GOT from this mode by touching the
7
display section, which may cause a touch switch to operate.
Note that the following occurs on the GOT when the backlight goes out.
8
• The POWER LED flickers (green/orange) and the monitor screen appears
9
blank.
0  The display section of the GT1595-X is an analog-resistive type touch panel.
If you touch the display section simultaneously in 2 points or more, the switch
that is located around the center of the touched point, if any, may operate.
Do not touch the display section in 2 points or more simultaneously.
1
Doing so may cause an accident due to incorrect output or malfunction.
2
 When programs or parameters of the controller (such as a PLC) that is
monitored by the GOT are changed, be sure to reset the GOT or shut off the
3
power of the GOT at the same time.
4
Not doing so can cause an accident due to false output or malfunction.
5
[DESIGN PRECAUTIONS]
6
CAUTION
7
8  Do not bundle the control and communication cables with main-circuit, power
or other wiring.
9
Run the above cables separately from such wiring and keep them a minimum
of 100mm apart.
0
Not doing so noise can cause a malfunction.
 Do not press the GOT display section with a pointed material as a pen or
driver.
Doing so can result in a damage or failure of the display section.
 When the GOT is connected to the Ethernet network, the available IP
address is restricted according to the system configuration.
• When multiple GOTs are connected to the Ethernet network :
Do not set the IP address (192.168.0.18) for the GOTs and the controllers in
the network.
• When a single GOT is connected to the Ethernet network :
Do not set the IP address (192.168.0.18) for the controllers except the GOT
in the network.
Doing so can cause the IP address duplication. The duplication can
negatively affect the communication of the device with the IP address
(192.168.0.18).
The operation at the IP address duplication depends on the devices and the
system.
 Turn on the controllers and the network devices to be ready for
communication before they communicate with the GOT.
Failure to do so can cause a communication error on the GOT.
[MOUNTING PRECAUTIONS]
WARNING
 Be sure to shut off all phases of the external power supply used by the
system before mounting or removing the GOT main unit to/from the panel.
Not doing so can cause the unit to fail or malfunction.
 Be sure to shut off all phases of the external power supply used by the
system before mounting or removing the communication unit, printer unit,
option function board or multi-color display board onto/from the GOT.
Not doing so can cause the unit to fail or malfunction.
 When installing the option function board or multi-color display board, wear
an earth band etc. to avoid the static electricity.
Not doing so can cause a unit corruption.
CAUTION
 Use the GOT in the environment that satisfies the general specifications
described in this manual.
Not doing so can cause an electric shock, fire, malfunction or product
damage or deterioration.
 When mounting the GOT to the control panel, tighten the mounting screws in
the specified torque range (0.36 to 0.48 N•m) with a Phillips-head screwdriver
No.2.
Undertightening can cause the GOT to drop, short circuit or malfunction.
Overtightening can cause a drop, short circuit or malfunction due to the
damage of the screws or the GOT.
 When loading the communication unit or printer unit to the GOT, fit it to the
connection interface of the GOT and tighten the mounting screws in the
specified torque range (0.36 to 0.48 N•m) with a Phillips-head screwdriver
No.2.
Under tightening can cause the GOT to drop, short circuit or malfunction.
Overtightening can cause a drop, failure or malfunction due to the damage of
the screws or unit.
 When mounting the multi-color display board onto the GOT, tighten the
mounting screws within the specified torque range (0.25 to 0.35 N•m) with a
Phillips-head screwdriver No.1.
Loose tightening may cause the unit and/or GOT to malfunction due to poor
contact.
Overtightening may damage the screws, unit and/or GOT; they might
malfunction.
 Push the option function board onto the corresponding connector until it
clicks, so that it will be secured firmly.
 Push the multi-color display board onto the corresponding connector so that it
will be secured firmly.
 When inserting a CF card into the GOT, push it into the insertion slot until the
CF card eject button will pop out.
If not properly inserted, a bad connection may cause a malfunction.
2. Part Names and Settings
Part Names and Settings of the GT15
Example)
GT1595
16)
2),3)
1)
4)
14) 14)
5)
6)
No. Name
Lit in green : Power is correctly supplied , Lit in orange :
Screen saving
1) POWER LED
Blinks in orange/green : Blown back light bulb , Not lit :
Power is not supplied
2) Display screen Displays the Utility and the user creation screen
For operating touch switches in the Utility and the user
3) Touch key
creation screen
For connecting a personal computer (Connector type: Mini-
4) USB interface
B)
For communicating with a controller or connecting a
5) RS-232 interface
personal computer(Connector type: D sub 9-pin)
Quantity 6) Power terminal Power input terminal, LG terminal*7, FG terminal
7) Extension interface For installing an extension unit
1
8) CF card interface For installing a CF card
8
9) CF card access Lit : CF card accessed , Not lit : CF card not accessed
1
Used for accepting or stopping the access to the CF card
1
before removing the CF card from the GOT
10) CF card access switch
ON :CF card being accessed (CF card removal prohibited)
1 OFF :CF card not accessed (CF card removal possible)
Optional function
11) For installing the optional function board
board
Multi-color display
4
12) For installing the multi-color display board
board interface*1*3*8
Hardware reset switch(Inoperative in the bus connection or
13) Reset switch
with the bus connection unit installed)
1
Hole for unit
14) Hole for inserting the unit installation fitting
installation fitting
15) Battery holderVideo Houses the battery
1
16) Human sensor*4 Sensor that detects human movement
17) Installation switch*5 Used for OS installations at the GOT startup
For installing the video input unit, RGB input unit, video/
18) Video/RGB interface*2
RGB input unit, or RGB output unit
Functional ground
19) For earthing
terminal*6
*1: For the multi-color display board, refer to the GT15 User's Manual.
*2: GT1585V-S and GT1575V-S only
*3: The GT155 has no multi-color display board.
*4: GT1595 and GT1585 only
*5:GT1595 only
*6:GT155 only
*7:The GT155 has no LG terminal.
*8:The GT1575-VN, GT1572-VN, and GT1562-VN do not support the 65536-color
display even if the multi-color display board is mounted.
3. Specifications
3.1 General Specifications
Item
Display
section
Operating
Zone
ambient
d'affichage
temperature
*1 Other than
Température the display
ambiante de section
fonctionnem Autre que la
*1
ent
zone
d'affichage
Storage ambient
temperature
Operating ambient
10 to 90% RH, non-condensing
*6
humidity
Storage ambient
10 to 90% RH, non-condensing
*6
humidity
Frequency
Compliant 5 to 8.4Hz
Under
with JIS B
*2 intermittent
Vibration resistance
3502 and
8.4 to150Hz
vibration
IEC 61131-
2
Under 5 to 8.4Hz
continuous
8.4 to 150Hz
vibration
[MOUNTING PRECAUTIONS]
 When inserting/removing a CF card into/from the GOT, turn the CF card
access switch off in advance.
Failure to do so may corrupt data within the CF card.ue to poor contact.
 When removing a CF card from the GOT, make sure to support the CF card
by hand, as it may pop out.
Failure to do so may cause the CF card to drop from the GOT and break.
 Operate and store the GOT in environments without direct sunlight, high
temperature, dust, humidity, and vibrations.
 When using the GOT in the environment of oil or chemicals, use the
protective cover for oil.
Failure to do so may cause failure or malfunction due to the oil or chemical
entering into the GOT.
[WIRING PRECAUTIONS]
 Be sure to shut off all phases of the external power supply used by the
system before wiring.
Failure to do so may result in an electric shock, product damage or
malfunctions.
 Always ground the FG terminal, LG terminal, and Functional ground terminal
of the GOT power to the functional ground conductors dedicated to the GOT.
Not doing so may cause an electric shock or malfunction.
 When tightening the terminal screws, use a Phillips-head screwdriver No.2.
 Terminal screws which are not to be used must be tightened always at torque
0.5 to 0.8 N•m.
Otherwise there will be a danger of short circuit against the solderless
terminals.
 Use applicable solderless terminals and tighten them with the specified
torque.
If any solderless spade terminal is used, it may be disconnected when the
terminal screw comes loose, resulting in failure.
 Correctly wire the GOT power supply section after confirming the rated
voltage and terminal arrangement of the product.
Not doing so can cause a fire or failure.
 Tighten the terminal screws of the GOT power supply section in the specified
torque range (0.5 to 0.8 N•m). Undertightening can cause a short circuit or
malfunction.
Overtightening can cause a short circuit or malfunction due to the damage of
the screws or the GOT.
 Exercise care to avoid foreign matter such as chips and wire offcuts entering
the GOT.
Not doing so can cause a fire, failure or malfunction.
 The module has an ingress prevention label on its top to prevent foreign
matter, such as wire offcuts, from entering the module during wiring.
Do not peel this label during wiring.
Before starting system operation, be sure to peel this label because of heat
dissipation.
 Plug the communication cable into the connector of the connected unit and
tighten the mounting and terminal screws in the specified torque range.
Undertightening can cause a short circuit or malfunction.
Overtightening can cause a short circuit or malfunction due to the damage of
the screws or unit.
 Plug the QnA/ACPU/Motion controller (A series) bus connection cable by
inserting it into the connector of the connected unit until it "clicks".
After plugging, check that it has been inserted snugly.
Not doing so can cause a malfunction due to a contact fault.
[TEST OPERATION PRECAUTIONS]
 Before performing the test operations of the user creation monitor screen
(such as turning ON or OFF bit device, changing the word device current
value, changing the settings or current values of the timer or counter, and
changing the buffer memory current value), read through the manual
carefully and make yourself familiar with the operation method.
During test operation, never change the data of the devices which are used to
perform significant operation for the system.
False output or malfunction can cause an accident.
[STARTUP/MAINTENANCE PRECAUTIONS]
 When power is on, do not touch the terminals.
Doing so can cause an electric shock or malfunction.
 Correctly connect the battery connector.
Do not perform the following actions to the battery.
• Charging, disassembling, heating, short-circuiting, or soldering the battery,
or throwing it into the fire
Doing so will cause the battery to produce heat, explode, or ignite, resulting in
injury and fire.
 Before starting cleaning or terminal screw retightening, always switch off the
power externally in all phases.
Not switching the power off in all phases can cause a unit failure or
malfunction.
Undertightening can cause a short circuit or malfunction.
Overtightening can cause a short circuit or malfunction due to the damage of
the screws or unit.
Item
Shock resistance
Operating atmosphere
GOT Rear face 7) 13) 17)
Operating altitude *3
Installation location
8)
*4
Overvoltage category
15)
Pollution degree *5
9) Cooling method
Grounding
10)
*1: When mounting MELSECNET/H communication unit (GT15-J71LP23-25,
GT15-J71BR13) or CC-Link communication unit (GT15-J61BT13), the
operating ambient temperature must be reduced 5°C against the maximum
12)
11)
values described in general specifications.
19) 18)
Lors du montage du module de communication MELSECNET/H (GT15-
J71LP23-25, GT15-J71BR13) ou du module de communication CC-Link
(GT15-J61BT13), la température ambiante de fonctionnement doit être réduite
de 5°C par rapport aux valeurs maximales décrites dans les spécifications
Description
générales.
*2: When using the MELSECNET/10 communication unit (GT15-75J71LP23-Z,
GT15-75J71BR13-Z) or CC-Link communication unit (GT15-75J61BT13-Z),
refer to the manual of the communication unit you use. (Differs with the
specification of GOT.)
*3: Do not use or store the GOT under pressure higher than the atmospheric
pressure of altitude 0m (0ft.). Failure to observe this instruction may cause a
malfunction.
When an air purge is made inside the control panel by adding pressure, there
may be a clearance between the surface sheet and the screen making it difficult
to use the touch panel, or the sheet may come off.
*4: This indicates the section of the power supply to which the equipment is
assumed to be connected between the public electrical power distribution
network and the machinery within the premises. Category II applies to
equipment for which electrical power is supplied from fixed facilities.
The surge voltage withstand level for up to the raged voltage of 300 V is 2500 V.
*5: This index indicates the degree to which conductive material is generated in the
environment where the equipment is used.
In pollution degree 2, only non-conductive pollution occurs but temporary
conductivity may be produced due to condensation.
*6: For the STN LCD model, the wet-bulb temperature must be 39°C or less.
Point
Refer to GT15 User's Manual for details of the performance specifications of each GOT.
3.2 Power Supply Specifications
The following indicates the power supply specifications for GT15
Note
Operation at momentary failure
• If an instantaneous power failure occurs in the power supply and continues for more
than the permissible period, the GOT will be reset.
• Make sure to power on the unit more than 5 seconds after power-off.
3.2.1 For GOTs powered from the 100 to 240VAC
power supply
Item
Input power supply voltage
Input frequency
Input max. apparent power
Power consumption
At backlight off
Inrush current
Specifications
Allowable momentary power
failure time
0 to 50
0 à 50 Noise immunity
Dielectric withstand voltage
Insulation resistance
0 to 55
0 à 55
Applicable wire size
Applicable solderless terminal
-20 to 60 Applicable tightening torque
(Terminal block terminal screw)
Half- Sweep
Acceleration
amplitude count
- 3.5mm 10 times
each in X,
2 Y and Z
9.8m/s -
directions
- 1.75mm
-
2
4.9m/s -
[STARTUP/MAINTENANCE PRECAUTIONS]
CAUTION
 Do not disassemble or modify the unit.
 Do not touch the conductive and electronic parts of the unit directly.
 The cables connected to the unit must be run in ducts or clamped.
 When unplugging the cable connected to the unit, do not hold and pull the
 Do not drop the module or subject it to strong shock. A module damage may
 Do not drop or give an impact to the battery mounted to the unit.
WARNING
 Before touching the unit, always touch grounded metals, etc. to discharge
 Replace battery with GT15-BAT by Mitsubishi electric Co. only.
CAUTION
 Dispose of used battery promptly.
[TOUCH PANEL PRECAUTIONS]
 For the analog-resistive film type touch panels, normally the adjustment is not
 When any difference between a touched position and the object position
[BACKLIGHT CHANGING PRECAUTIONS]
 Before changing the backlight, always switch off the GOT power externally in
 When replacing the backlight, use the gloves.
 Start changing the backlight more than 5 minutes after switching the GOT
[DISPOSAL PRECAUTIONS]
 When disposing of the product, handle it as industrial waste.
WARNING
[TRANSPORTATION PRECAUTIONS]
 When transporting lithium batteries, make sure to treat them based on the
 Make sure to transport the GOT main unit and/or relevant unit(s) in the
WARNING
 When fumigants that contain halogen materials such as fluorine, chlorine,
3.2.2 For GOTs powered from the 24VDC power
Specifications
2
Compliant with JIS B 3502 and IEC 61131-2 147 m/s (15G),
3 times each in X, Y and Z directions
No greasy fumes, corrosive gas, flammable gas, excessive
conductive dust, and direct sunlight (Same as storage
atmosphere)
2000 m (6562 ft) max.
Inside control panel
II or less
2 or less
Self-cooling
Grounding with a resistance of 100Ω or less
Input power
supply voltage
Power
consumption
Inrush current
Allowable
momentary power
failure time
Noise immunity
Dielectric
withstand voltage
Insulation
resistance
Applicable wire
size
Applicable
solderless
terminal
Applicable
tightening torque
(Terminal block
terminal screw)
3.3 External Dimensions
.
Specifications
GT1575V-STBA,
GT1575-STBA,
GT1575-VTBA,
GT1585V-STBA,
GT1595-XTBA GT1575-VNBA,
GT1585-STBA
GT1572-VNBA,
GT1565-VTBA,
GT1562-VNBA
100 to 240VAC (+10%, -15%)
50/60Hz±5%
110VA (maximum load)
56W or less 41W or less 39W or less
30W or less 28W or less
50A or less 45A or less
40A or less (4ms)
(4ms) (4ms)
(maximum load)
(maximum load) (maximum load)
20ms or less (100VAC or more)
1,500Vp-p noise voltage, 1 s noise width (when
measuring with a noise simulator under 25 to 60Hz
noise frequency)
1500VAC for 1 minute across power terminals and earth
10M or more across power terminals and earth by a
500VDC insulation resistance tester
2
0.75 to 2 [mm ]
Solderless terminal for M3 screw RAV1.25-3, V2-S3.3,
V2-N3A, FV2-N3A
0.5 to 0.8 [N•m]
CAUTION
Doing so can cause a failure, malfunction, injury or fire.
Doing so can cause a unit malfunction or failure.
Not doing so can cause the unit or cable to be damaged due to the dangling,
motion or accidental pulling of the cables or can cause a malfunction due to a
cable connection fault.
cable portion.
Doing so can cause the unit or cable to be damaged or can cause a
malfunction due to a cable connection fault.
result.
Doing so may damage the battery, causing the battery fluid to leak inside the
battery.
If the battery is dropped or given an impact, dispose of it without using.
static electricity from human body, etc.
Not doing so can cause the unit to fail or malfunction.
Use of another battery may present a risk of fire or explosion.
Keep away from children. Do not disassemble and do not dispose of in fire.
CAUTION
required. However, the difference between a touched position and the object
position may occur as the period of use elapses.
When any difference between a touched position and the object position
occurs, execute the touch panel calibration.
occurs, other object may be activated. This may cause an unexpected
operation due to incorrect output or malfunction.
WARNING
all phases (when the GOT is connected to the bus, the PLC CPU power must
also be switched off externally in all phases) and remove the GOT from the
control panel.
Not switching the power off in all phases may cause an electric shock.
Not removing the unit from the control panel can cause injury due to a drop.
CAUTION
Otherwise, it may cause you to be injured.
power off.
Not doing so can cause a burn due to the heat of the backlight.
CAUTION
When disposing of the battery, dispose of it separately based on the law in
each region.
(Refer to the User's Manual for the GOT you are using for details of the
battery regulations in the EU member countries.)
CAUTION
transport regulations.
(Refer to the User's Manual for the GOT you are using for details of the
regulated models.)
manner they will not be exposed to the impact exceeding the impact
resistance described in the general specifications of the User's Manual, as
they are precision devices.
Failure to do so may cause the unit to fail.
Check if the unit operates correctly after transportation.
bromine, and iodine are used for disinfecting and protecting wooden
packaging from insects, they cause malfunction when entering our products.
Please take necessary precautions to ensure that remaining materials from
fumigant do not enter our products, or treat packaging with methods other
than fumigation (heat method).
Additionally, disinfect and protect wood from insects before packing products.
supply
Specifications
GT1575V-
STBD,
GT1575-
STBD,
GT1575-
GT1585
VTBD,
Item GT1595- V-STBD, GT1555- GT1555- GT1555- GT1550-
GT1575-
XTBD GT1585- VNBD, V QTBD QSBD QLBD
STBD GT1572-
VNBD,
GT1565-
VTBD,
GT1562-
VNBD
24VDC (+25%, -20%)
15W or
57W or 43W or 41W or 19W or 18W or 17W or
less
less less less less less less
(620mA
(2380mA (1790mA (1710mA (790mA/ (750mA/ (710mA/
/
/24VDC) /24VDC) /24VDC) 24VDC) 24VDC) 24VDC)
24VDC)
32W or 14W or
less 30W or less less
At backlight
13W or less (540mA/24VDC)
off
(1330mA (1250mA/24VDC) (580mA/
/24VDC) 24VDC)
67A or
100A or
less
less
115A or less (1ms) (1ms) 60A or less (1ms) (maximum
(4ms)
(maximum load) (maxi- load)
(maximu
mum
m load)
load)
10 ms or less
500Vp-p noise voltage, 1 s noise width (when measuring with a noise simulator
under 25 to 60Hz noise frequency)
500VDC for 1 minute across power terminals and earth
10M or more across power terminals and earth by a 500V DC insulation
resistance tester
2
0.75 to 2 [mm ]
Solderess terminal for M3 screw RAV1.25-3, V2-S3.3, V2-N3A, FV2-N3A
0.5 to 0.8 [N•m]
GT1595 GT1585
397(15.6) 316(12.44)
320(12.6) 263(10.35)
320(12.6)
250(9.84)
382(15.0)
301(11.85)
Unit : mm(inch)
Unit: mm (inch)
GT157 GT156
303 (11.93) 241 (9.49)
252 (9.92)
175.5 (6.91)
222 (8.74)
175.5 (6.91)
288 (11.34)
226 (8.90)
Unit: mm (inch)
Unit : mm(inch)
GT155
167 (6.58)
110 (4.33)
110 (4.33)
152 (5.99)
Unit : mm(inch)