Quoizel Stonington SNN8408K Assembly Instruction Sheet

Please go to www.quoizel.com
Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
Light Source: (1) A19 Medium Base bulb 100W Maximum.
Estimated Assembly Time:
Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are
present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact customer service for replacement
parts.
Fixture can only be mounted in the direction indicated.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
Package Contents
Crossbar
A Assembly
x 1
Outlet Box Screw
C
x 2
Alternate
Mounting
E
Screw
Wire Connector
D
x 2
x 3
-
STEP 1 Install Crossbar Assembly
A. Pass the supply wires through the Crossbar Assembly (A). Attach
the Crossbar Assembly (A) to the Outlet Box with the head of the
Green Ground Screw facing you. Secure it with Outlet Box Screws
(C). Tighten until snug.
Outlet
Box
Figure 1
STEP 2 - Test Fit the Backplate
to the Crossbar Assembly
A. Remove the mounting balls from
the Crossbar Assembly (A).
Place the backplate and Fixture
Body (B) onto the Crossbar
Assembly (A) and secure with
mounting balls. Note: The
backplate and Fixture Body (B)
should be snug against the wall
and held tight with the mounting
balls. If it is not, adjust the length
of the mounting screws on the
Crossbar Assembly (A) by
unscrewing the preassembled
hex nut and lock washer and then screwing the mounting screws in
or out of the crossbar until the correct length is achieved. Once the
backplate and Fixture Body (B) is secure, remove the mounting ball
and Fixture Body (B) and proceed to Step 3.
2018 QuoizelInc.
Assembly Instruction Sheet #IS-SNN8408
For Styles SNN8408K, SNN8408PN and SNN8408W
for product cleaning tips. Go to the
20-30 minutes
B
A
C
Supply Wires
with Ground Wire
Backplate
Mounting
Mounting Ball
Screw
A
Hex Nut and
Lock Washer
Figure 2
visit us on-line at www.quoizel.com
Care + Maintenance selection.
STEP 3 - Wire Connections
A. Wrap bare or green ground wire around green ground screw on the
crossbar, no less than 2 inches from the end of the wire. Tighten the
green ground screw.
B. Use standard wire connectors (D) to make all wire connections.
Twist connectors until wires are tightly joined together. Wrap each
connection with approved electrical tape and carefully stuff all the
connected wires into the Outlet Box.
Fixture Body from outlet box
x 1
Black wire from
outlet box (or Red)
Bare, or Green
Ground wire
from outlet box
STEP 4 - Install the Fixture Body
A. Position the backplate and Fixture Body (B) onto the Crossbar
Assembly (A). Place the holes in the backplate over the mounting
screws. Secure the Fixture Body by using the mounting balls and
hand tighten the mounting balls until snug.
Figure 4
B
STEP 5 - Install the Bulb and Apply Silicone Sealer
A. Insert the bulb onto socket and screw snugly into place.
B. Make sure the exterior wall surface and fixture backplate are free of
dirt before applying caulk. Using exterior grade caulk, caulk over top
1of2
White wire
Green Ground Screw
on the Crossbar
Backplate
A
Mounting Ball
Mounting Screw
White wire
from fixture
Black wire
from fixture
Ground wire
from Fixture
Figure 3
B
ReleasedDate:2018-11-12