Advertisement
4. TO CHANGE THE UNIT CODE (NUMBER CODE):
a. Press the "OFF-1" button, the Remote will set to Unit Code "1".
b. For each repeated press of the "OFF-1" button, the unit code will be set to the next incremental number code. (i.e., 1 push = "1",
2 total pushes = "2", 3 total pushes = "3", ... 16 total pushes = "16"
5. TO COMPLETE PROGRAMMING:
Press the "OFF-2" or "ON-2" button. The LED will stop flashing and the new code will be entered into memory.
NOTE: When the Unit (number) Code for button "1" in entered as "16", then button "2" will be assigned Unit (number) Code "1".
An alternate method of programming is available (if desired) to match the code of an existing device when its code is not known.
Programming is as follows:
1. Place unit in programming mode per directions.
2. TO FIND THE HOUSE CODE (LETTER CODE):
a. Determine what device (transceiver, dimmer, or switch) you want to control from the Remote. Verify that the device is set so the load is
OFF.
b. Press the "ON-1" button. The Remote will set to House Code "A" and send an "ALL 'A' ON" command. Note whether the intended
device (transceiver, dimmer, or switch) responds by turning its load ON.
c. If the device does not turn ON, continue to press the "ON-1" button. This will increase the letter code one letter for each push. When
the selected House (letter) Code matches the House Code of the intended device (transceiver, dimmer, or switch), it will turn ON its
load.
3. TO FIND THE UNIT CODE (NUMBER CODE):
a. While still in the program mode, use the device previously set for the proper House (letter) Code.
b. Press the "OFF-1" button. The remote will set to Unit Code "1" and send an "X1-OFF" command with "X" being the House (letter) Code
determined in the above step. Note whether the intended device (transceiver, dimmer, or switch) responds by turning its load OFF.
c. If the device does not turn OFF, continue to press the "OFF-1" button. This will increase the Unit (number) Code one number for each
push. When the selected Unit (number) code matches the unit code of the intended device (transceiver, dimmer, or switch), it will turn
OFF its load.
d. Complete programming by pressing button "OFF-2" or "ON-2".
NOTE: When a new code is set, it will remain in memory until either it's reset to A1 or another code is selected.
1. Using a small screwdriver, gently pry apart the 2 halves of the key chain housing (refer to Figure 3).
2. The battery is found in the holder in the back housing.
3. Carefully remove the battery from the holder.
4. Replace with a fresh battery observing proper polarity. USE ONLY A CR2032 LITHIUM BATTERY.
5. Assemble key chain remote by aligning the 2 housing halves together. Squeeze until the housings snap together.
• Lights and loads do not respond; LED does not flash when buttons are pushed
- Battery weak or exhausted – replace battery.
- Battery installed incorrectly – check battery for proper polarity.
• Lights and loads do not respond and LED flashes when buttons are pushed
- Out of range – Units range is limited to 75 feet. Move closer to transceiver location.
- Codes not properly set on key chain transmitter, transceiver, or other DHC devices – properly set code of key chain and/or transceiver,
to match devices.
• Some lights and loads do not respond and LED flashes when buttons are pushed
- Codes not properly set on key chain transmitter, transceiver, or other DHC devices – properly set code of key chain and/or transceiver,
to match devices.
CHANGING BATTERY
TROUBLESHOOTING
Figure 1 - Remote Functions
"2" ON
"2" OFF
Figure 2 - Remote w/Keychain
Figure 3 - Battery Replacement
Battery
Gently pry up
with small
screwdriver
"1" ON
"1" OFF
DI-000-HCCKR-00A
Advertisement
